Densities, Viscosities of Pure 1-(2-Hydroxyethyl) Pyrrolidine, 3-Amino-1-Propanol, Water, and Their Mixtures at 293.15 to 363.15 K and Atmospheric Pressure
Ontology highlight
ABSTRACT:
SUBMITTER:
PROVIDER: S-EPMC10009753 | biostudies-literature | 2023 Feb
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Aqueous amine solvents are used to capture CO2 from various flue gas sources. In this work, the chemical stability of a blend of 3-amino-1-propanol (3A1P) and 1-(2-hydroxyethyl)pyrrolidine [1-(2HE)PRLD] was studied. The chemical stability tests were conducted both in batch and cycled systems using various oxygen and NOx concentrations, additives (iron), and temperatures. In the thermal degradation experiments with CO2 present, the blend was more stable than the primary amines [(3A1P or monoethanolamine (MEA)] but less stable than the tertiary amine 1-(2HE)PRLD alone. Similar stability was observed between MEA, 3A1P, and the blend in the batch experiments at medium oxygen concentration (21% O2) and no iron present. 1-(2HE)PRLD was more stable. However, the presence of high oxygen concentration (96% O2) and iron reduced the stability of 1-(2HE)PRLD significantly. Furthermore, in the case of the blend, the chemical stability increased with increasing promoter concentration in batch experiments. During the cyclic experiment, the amine loss for the blend was similar to what was previously observed for MEA (30 wt %) under the same conditions. A thorough mapping of degradation compounds in the solvent and condensate samples resulted in the identification and quantification of 30 degradation compounds. The major components in batch and cycled experiments varied somewhat, as expected. In the cyclic experiments, the major components were ammonia, 3-(methylamino)-1-propanol (methyl-AP), N,N'-bis(3-hydroxypropyl)-urea (AP-urea), pyrrolidine, formic acid (formate), and N-(3-hydroxypropyl)-glycine (HPGly). Finally, in this paper, formation pathways for the eight degradation compounds (1,3-oxazinan-2-one, AP-urea, 3-[(3-aminopropyl)amino]-1-propanol, tetrahydro-1-(3-hydroxypropyl)-2(1H)-pyrimidinone, methyl-AP, N-(3-hydroxypropyl)-formamide, N-(3-hydroxypropyl)-β-alanine, and HPGly) are suggested.
| S-EPMC9838088 | biostudies-literature
Project description:The solubility of warfarin sodium isopropanol solvate (WS·IPA), a widely used anticoagulant, was determined at temperatures ranging from 278.15 to 333.15 K in four pure solvents (acetone, ethanol, IPA, and water), five binary solvent mixtures (IPA + acetone, IPA + ethanol, IPA + water, IPA + heptane, and IPA + hexane), and five ternary solvent mixtures (IPA + acetone + heptane, IPA + acetone + hexane, IPA + ethanol + heptane, IPA + ethanol + hexane, and IPA + water + heptane) using the polythermal method. It was demonstrated that the solubility of WS·IPA increases with increasing temperature in the pure solvents and at constant solvent composition in the solvent mixtures. In addition, the solubility of WS·IPA in IPA increases with increasing content of acetone, ethanol, and water, which act as cosolvents, and decreases with increasing content of heptane and hexane, which act as antisolvents. The experimental solubility data of WS·IPA in pure solvents and binary and ternary solvent mixtures were correlated using the modified Apelblat and λh model equations. The correlated solubility data agree with the experimental data based on the relative deviation and the average relative deviation (ARD %) values. Thus, the correlated and experimentally derived solubility data of WS·IPA provide a pathway to engineer advanced pharmaceutical crystallization processes for WS·IPA.
| S-EPMC7291792 | biostudies-literature
Project description:In this paper we demonstrate the application of pressure perturbation calorimetry (PPC) to the characterization of 2-propanol/water mixtures. PPC of different 2-propanol/water mixtures provides two useful measurements: (i) the change in heat (ΔQ); and (ii) the [Formula: see text] value. The results demonstrate that the ΔQ values of the mixtures deviate from that expected for a random mixture, with a maximum at ~20-25 mol% 2-propanol. This coincides with the concentration at which molecular dynamics (MD) simulations show a maximum deviation from random distribution, and also the point at which alcohol-alcohol hydrogen bonds become dominant over alcohol-water hydrogen bonds. Furthermore, the [Formula: see text] value showed transitions at 2.5 mol% 2-propanol and at approximately 14 mol% 2-propanol. Below 2.5 mol% 2-propanol the values of [Formula: see text] are negative; this is indicative of the presence of isolated 2-propanol molecules surrounded by water molecules. Above 2.5 mol% 2-propanol [Formula: see text] rises, reaching a maximum at ~14 mol% corresponding to a point where mixed alcohol-water networks are thought to dominate. The values and trends identified by PPC show excellent agreement not only with those obtained from MD simulations but also with results in the literature derived using viscometry, THz spectroscopy, NMR and neutron diffraction.
| S-EPMC5241351 | biostudies-literature
Project description:The OH-initiated degradation of 2-amino-2-methyl-1-propanol [CH3C(NH2)(CH3)CH2OH, AMP] was investigated in a large atmospheric simulation chamber, employing time-resolved online high-resolution proton-transfer reaction-time-of-flight mass spectrometry (PTR-ToF-MS) and chemical analysis of aerosol online PTR-ToF-MS (CHARON-PTR-ToF-MS) instrumentation, and by theoretical calculations based on M06-2X/aug-cc-pVTZ quantum chemistry results and master equation modeling of the pivotal reaction steps. The quantum chemistry calculations reproduce the experimental rate coefficient of the AMP + OH reaction, aligning k(T) = 5.2 × 10-12 × exp (505/T) cm3 molecule-1 s-1 to the experimental value kexp,300K = 2.8 × 10-11 cm3 molecule-1 s-1. The theoretical calculations predict that the AMP + OH reaction proceeds via hydrogen abstraction from the -CH3 groups (5-10%), -CH2- group, (>70%) and -NH2 group (5-20%), whereas hydrogen abstraction from the -OH group can be disregarded under atmospheric conditions. A detailed mechanism for atmospheric AMP degradation was obtained as part of the theoretical study. The photo-oxidation experiments show 2-amino-2-methylpropanal [CH3C(NH2)(CH3)CHO] as the major gas-phase product and propan-2-imine [(CH3)2C═NH], 2-iminopropanol [(CH3)(CH2OH)C═NH], acetamide [CH3C(O)NH2], formaldehyde (CH2O), and nitramine 2-methyl-2-(nitroamino)-1-propanol [AMPNO2, CH3C(CH3)(NHNO2)CH2OH] as minor primary products; there is no experimental evidence of nitrosamine formation. The branching in the initial H abstraction by OH radicals was derived in analyses of the temporal gas-phase product profiles to be BCH3/BCH2/BNH2 = 6:70:24. Secondary photo-oxidation products and products resulting from particle and surface processing of the primary gas-phase products were also observed and quantified. All the photo-oxidation experiments were accompanied by extensive particle formation that was initiated by the reaction of AMP with nitric acid and that mainly consisted of this salt. Minor amounts of the gas-phase photo-oxidation products, including AMPNO2, were detected in the particles by CHARON-PTR-ToF-MS and GC×GC-NCD. Volatility measurements of laboratory-generated AMP nitrate nanoparticles gave ΔvapH = 80 ± 16 kJ mol-1 and an estimated vapor pressure of (1.3 ± 0.3) × 10-5 Pa at 298 K. The atmospheric chemistry of AMP is evaluated and a validated chemistry model for implementation in dispersion models is presented.
| S-EPMC8419843 | biostudies-literature
Project description:In order to evaluate the impact of the alkyl side chain length and symmetry of the cation on the thermophysical properties of water-saturated ionic liquids (ILs), densities and viscosities as a function of temperature were measured at atmospheric pressure and in the (298.15 to 363.15) K temperature range, for systems containing two series of bis(trifluoromethylsulfonyl)imide-based compounds: the symmetric [C n C n im][NTf2] (with n = 1-8 and 10) and asymmetric [C n C1im][NTf2] (with n = 2-5, 7, 9 and 11) ILs. For water-saturated ILs, the density decreases with the increase of the alkyl side chain length while the viscosity increases with the size of the aliphatic tails. The saturation water solubility in each IL was further estimated with a reasonable agreement based on the densities of water-saturated ILs, further confirming that for the ILs investigated the volumetric mixing properties of ILs and water follow a near ideal behaviour. The water-saturated symmetric ILs generally present lower densities and viscosities than their asymmetric counterparts. From the experimental data, the isobaric thermal expansion coefficient and energy barrier were also estimated. A close correlation between the difference in the energy barrier values between the water-saturated and pure ILs and the water content in each IL was found, supporting that the decrease in the viscosity of ILs in presence of water is directly related with the decrease of the energy barrier.
| S-EPMC5024754 | biostudies-literature
Project description:Synthetic esters are used as lubricants for applications at high temperatures, but their development can be a trial and error process. In this context, molecular dynamics simulations could be used as a tool to investigate the properties of new lubricants, in particular viscosity. We employ nonequilibrium molecular dynamics (NEMD) simulations to predict bulk Newtonian viscosities of a set of mixtures of two esters, di(2-ethylhexyl) sebacate (DEHS) and di(2-ethylhexyl) adipate (DEHA) at 293 and 343 K as well as equilibrium molecular dynamics (EMD) and NEMD at 393 K and compare these to experimental measurements. The simulations predict mixture densities within 5% of the experimental values, and we are able to retrieve between 99% and 75% of the experimental viscosities for all ranges of temperature. Experimental viscosities show a linear trend which we are able to capture using NEMD at low temperature and EMD at high temperature. Our work shows that, using EMD and NEMD simulations, and the workflows we developed, we can obtain reliable estimates of the viscosities of mixtures of industrially relevant ester-based lubricants at different temperatures.
| S-EPMC10041636 | biostudies-literature
Project description: Not available
| S-EPMC11317982 | biostudies-literature
Project description:Physical properties of the binary solutions, toluene with 2-propanol and 2-methyl-1-propanol, were measured at T = 293.15, 298.15, 303.15, 308.15, and 313.15 K and P = 100 kPa. The experimental density values were tested with the Emmerling et al. and Gonzalez-Olmos-Iglesias equations. The results indicate that the equation by Emmerling et al. is the best to correlate the density for toluene + 2-methyl-1-propanol system, while for toluene + 2-propanol, both proposed equations are proper to correlate the density with composition and temperature. The viscosity results were verified with different models containing two adjustable parameters. The values of viscosity deviation (∆η), excess molar volume (VE), excess Gibbs energy (ΔG*E), partial molar volumes (V1¯ and V2¯), and apparent molar volume (Vφ,1 and Vφ,2) were calculated. The values of the excess molar volume were positive for both systems, while negative values were obtained for the viscosity deviation and the excess Gibbs energy. The excess properties of the mixtures were adjusted to the Redlich-Kister equation. The values of thermodynamic functions of activation of viscous flow were computed and analyzed. Additionally, the Prigogine-Flory-Patterson (PFP) theory was applied to calculate VE and then compared with experimental values. The values of the percentage absolute average deviation obtained suggest the validity of this theory. The Fourier transform infrared spectroscopy (FTIR) spectra of the binary solutions studied in this work allowed for the understanding of the interactions between the molecules of these systems.
| S-EPMC11477799 | biostudies-literature
Project description:Ionic-liquid-based aqueous biphasic systems (IL-based ABS) have been largely investigated as promising extraction and purification routes. In this context, the determination of their phase diagrams and the physical properties of the coexisting phases are of high relevance when envisaging their large-scale applications. Low viscosities improve the mass transfer and reduce energy consumptions, while the knowledge on their densities is important for the equipment design. In this work, novel phase diagrams for aqueous solutions of imidazolium-based ILs combined with acetate-based salts, namely KCH3CO2 or NaCH3CO2, are reported and discussed. The ability of the acetate-based salts to induce the phase separation not only depends on the ions hydration energy, but also on the concentration of "free" ions in solution. The tie-lines, tie-line lengths and critical points are also addressed. Experimental measurements of density and viscosity of the coexisting phases, for the different systems and at several compositions and temperatures, are additionally presented. The Othmer-Tobias and Bancroft equations are also applied to ascertain on the tie-lines coherence. It is here shown that low-viscous IL-based ABS, with a high difference in the densities of the coexisting phases, can be formed with organic and biodegradable salts thus offering enhanced features over conventional polymer-based systems.
| S-EPMC5332031 | biostudies-literature
Project description:Non-targeted analysis (NTA) is a rapidly evolving analytical technique with numerous opportunities to improve and expand instrumental and data analysis methods. In this work, NTA was performed on eight synthetic mixtures containing 1264 unique chemical substances from the U.S. Environmental Protection Agency's Non-Targeted Analysis Collaborative Trial (ENTACT). These mixtures were analyzed by atmospheric pressure chemical ionization (APCI) and electrospray ionization (ESI) using both positive and negative polarities for a total of four modes. Out of the 1264 ENTACT chemical substances, 1116 were detected in at least one ionization mode, 185 chemicals were detected using all four ionization modes, whereas 148 were not detected. Forty-four chemicals were detected only by APCI, and 181 were detected only by ESI. Molecular descriptors and physicochemical properties were used to assess which ionization type was preferred for a given compound. One ToxPrint substructure (naphthalene group) was found to be enriched in compounds only detected using APCI, and eight ToxPrints (e.g., several alcohol moieties) were enriched in compounds only detected using ESI. Examination of physicochemical parameters for ENTACT chemicals suggests that those with higher aqueous solubility preferentially ionized by ESI-. While ESI typically detects a larger number of compounds, APCI offers chromatograms with less background, fewer co-elutions, and additional chemical space coverage, suggesting both should be considered for broader coverage in future NTA research. Graphical abstract.
| S-EPMC7477815 | biostudies-literature