Feasibility study of juxta-articular-type volar distal radius plate (ARIX Wrist System) for surgically treating marginal distal radius fractures
Ontology highlight
ABSTRACT: Purpose
We evaluated the feasibility of a juxta-articular-type volar distal radius plate for the surgical treatment of marginal distal radius fractures. Materials and methods
Twenty marginal distal radius fractures, defined by the location of the fracture line within 10 mm of the joint line of the lunate fossa, were retrospectively reviewed between July 2020 and July 2022. The fractures were fixed using a juxta-articular-type volar plate (ARIX Wrist System). The characteristics of the implant and surgical technique, radiologic, and clinical outcomes, and related complications were evaluated. Results
Bony union was achieved in all patients within six months. Acceptable radiological alignment was achieved with no significant differences between the fractured and the normal sides. The clinical outcomes were favorable, with satisfactory functional outcomes. There was one case of post-traumatic arthritis and two cases of carpal tunnel syndrome. No implant-related complications including flexor tendon problems were observed. Conclusion
The juxta-articular distal radius plate of the Arix Wrist system is feasible for treating marginal distal radius fractures and achieves favorable clinical outcomes without implant-related complications in East Asian patients.
SUBMITTER: Lee B
PROVIDER: S-EPMC10121617 | biostudies-literature | 2023 Mar
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:BackgroundA volar locking plate (VLP) is the most frequently used form of implant used for open reduction and internal fixation of distal radius fractures. They are known to have a complication rate of up to 27%. We hypothesized that plate design could influence complication rates.MethodsWe performed a review of patients undergoing VLP fixation for distal radius fracture. A total of 228 patients underwent fixation with the Distal Volar Radial Anatomical (DVR) plate; 388 patients underwent fixation with the VariAx plate. Independent observers performed blinded case note and radiographic review, to assess for the quality of reduction, and complications for the inserted VLP.ResultsMean time to surgery was 6.0 days; mean follow-up was 17.5 weeks. Mean age was 56.5 years. The quality of reduction was classified as anatomical (46%), good (36.3%), moderate (13.0%), or poor (3.9%). Complications were identified in 109 patients (17%). Plate prominence was seen in 133 patients (21%). The DVR plate was less prominent ( P < .001) and had better overall radiographic appearances ( P = .025). Flexor tendon complications were related to plate prominence ( P = .005). Inferior reduction was associated with increased time to surgery ( P = .020).ConclusionsThis study highlights the importance of prompt surgery, effective fracture reduction, and careful plate positioning to avoid volar prominence.
| S-EPMC6081777 | biostudies-literature
Project description:IntroductionThe aim of this systematic review and meta-analysis was to evaluate whether volar locking plate (VLP) fixation leads to better clinical and radiological outcomes than those of closed reduction and cast immobilization for the treatment of distal radius fractures (DRFs).Materials and methodsA comprehensive literature search was performed in PubMed, Web of Science, and Cochrane databases up to January 2022. Inclusion criteria included randomized controlled trial (RCT) studies comparing VLP fixation with cast immobilization for DRFs. Investigated parameters were Patient-Rated Wrist Evaluation questionnaire, Disabilities of the Harm, Shoulder, and Hand score (DASH), range of motion (ROM), grip strength, quality of life (QoL), radiological outcome, and complication and reoperation rate, both at short- and mid-/long-term follow-up. Assessment of risk of bias and quality of evidence was performed with Downs and Black's 'Checklist for Measuring Quality'.ResultsA total of 12 RCTs (1368 patients) were included. No difference was found for ROM, grip strength, QoL, and reoperation, while the DASH at 3 months was statistically better in the VLP group (P < 0.05). No clinical differences were confirmed at longer follow-up. From a radiological perspective, only radial inclination (4°) and ulnar variance (mean difference 1.1 mm) at >3 months reached statistical significance in favor of the VLP group (both P < 0.05). Fewer complications were found in the VLP group (P < 0.05), but they did not result in different reintervention rates.ConclusionsThis meta-analysis showed that the surgical approach leads to a better clinical outcome in the first months, better fracture alignment, and lower complication rate. However, no differences in the clinical outcomes have been confirmed after 3 months. Overall, these findings suggest operative treatment for people with higher functional demand requiring a faster recovery, while they support the benefit of a more conservative approach in less demanding patients.
| S-EPMC9624483 | biostudies-literature
Project description:Four cases of flexor tendon problems which developed after volar plate fixation of distal radius fractures are presented. All cases were associated with close contact of the screws or distal edge of the plate with the flexor tendons. Poor bone stock or multiple bone fragments allowing loosening of the plate or non-locking screws cause the hardware to irritate the flexor tendons and ultimately lead to rupture. The flexor tendons involved include the flexor carpi radialis, flexor pollicis longus and flexor digitorum superficialis, and flexor digitorum profundus to the index and long fingers.
| S-EPMC2787213 | biostudies-other
Project description:The aim of this study was to define the outcome and complications following open reduction and internal fixed-angle plating of distal radius fractures for patients on chronic immunosuppression medications. A retrospective study identified 11 patients with distal radius fractures that had been on chronic immunosuppressive medication. The mean patient age was 59.9 years (40-82 years). According to the Orthopedic Trauma Association classification, there was one 23A3, one 23B3, and nine 23C type fractures. There were two open fractures. All patients received preoperative antibiotics and underwent reduction and fixation with a volar, fixed-angle plate. Postoperative measurements included postoperative and final radiographic indices, wrist flexion and extension, forearm rotation, and grip strength. Clinical follow-up averaged 13 months, and radiographic follow-up averaged 14.9 months. Statistical analysis was performed comparing means of various parameters with a two-sided t test with an alpha value < or = 0.05. All fractures healed, and there were no infections. The final mean ulnar variance, volar tilt, and radial inclination were -0.1 mm (ulnar negative; -2.0 to +2.5 mm), 13 degrees (5-23 degrees), and 21 degrees (15-27 degrees), respectively. The mean articular gap or step was 0.4 mm. There was a small but significant decrease between the final and postoperative mean ulnar variance (p = 0.03). Mean wrist flexion was 47 degrees, extension 47 degrees , pronation 77 degrees, and supination was 76 degrees. Grip strength averaged 16.3 kg versus 25.1 kg for the opposite extremity. The one major complication included a postoperative carpal tunnel syndrome. Fixed-angle volar plate fixation for distal radius fractures in patients with chronic immunosuppression was associated with union (with acceptable radiographic alignment), no wound-healing problems or infections, and with functional wrist and forearm motion and grip strength.
| S-EPMC2584208 | biostudies-other
Project description:Background and purposeA better understanding of factors that influence functioning may improve the identification of patients with distal radius fractures (DRFs) who need hand therapy. The purpose of this scoping review was to provide a comprehensive overview of factors that have been evaluated for their influence on hand functioning following volar plate fixation of DRFs.Material and methods6 databases were searched from 2005 to 2021 for publications regarding surgical treatment for a DRF with a volar locking plate. Included studies evaluated demographic, perioperative, and postoperative factors within the 6 weeks post-surgery for their influence on functioning at least 3 months post-surgery. Functioning was assessed with patient-reported outcome measures. The factors were categorized into themes and mapped to the International Classification of Functioning, Disability and Health (ICF).Results148 studies were included. 708 factors were categorized into 39 themes (e.g. pain) and mapped to the ICF components. The themes were primarily mapped to "body functions and structures" (n = 26) and rarely to "activities and participation" (n = 5). Fracture type (n = 40), age (n = 38), and sex (n = 22) were the most frequently evaluated factors.ConclusionThis scoping review identified an extensive number of factors evaluated within 6 weeks after surgery for their influence on functioning at least 3 months after volar plate fixation of a DRF and the existing research has primarily evaluated factors related to "body functions and structures," with limited focus on factors related to "activities and participation."
| S-EPMC10253938 | biostudies-literature
Project description:Background We evaluated the detection for screw penetration on the dorsal cortex of the radius in serial oblique, dorsal tangential, and radial groove radiographic views in volar plating fixation. Materials and Methods Eight screw positions were set in each of the four cadaveric radii. Screw 1 was placed in the styloid subregion, whereas screws 2 and 3 were placed just proximal to the styloid and were defined for the radial region of the radius. Screws 4 (distal to the extensor pollicis longus [EPL] groove), 5 (the distal half of the groove), and 6 (the proximal half of the groove) were placed in the central region of the radius. Screws 7 (just medial to the groove) and 8 (sigmoid notch subregion) were positioned in the ulnar region of the radius. The screws were overlengthened by 1 and 2 mm and were evaluated in three radiographic views. Results Penetrations in the radial region were fully visible in supinated oblique views with 1- and 2-mm overlengthened screws. The penetration of screw 4 was clearly observable over a considerable range of views. However, the 1-mm penetration of screw 5 was not detectable at any angle of projection. Detection of the ulnar region screw was the most difficult among the three regions with oblique views. In the dorsal tangential view, the 1-mm penetration of screw 4 was not observed in any of the four radii, but the penetration of screw 5 was detectable in all the radii. The screws 2, 3, 5, 7, and 8 were readily detectable. The screw 4 was barely seen in the radial groove view, while the screws 5 and 6 were readily detectable. Conclusion/Clinical Relevance Appropriate combinations of these well-known radiological views are essential for the overall detection of penetrated screws during plating in distal radius fractures.
| S-EPMC5658214 | biostudies-literature
Project description:AimTo investigate the cost-effectiveness of Volar Locking Plate (VLP) compared to External Fixation (EF) for unstable dorsally displaced distal radius fractures in a 3-year perspective.MethodsDuring 2009-2013, patients aged 50-74 years with an unstable dorsally displaced distal radius fracture were randomised to VLP or EF. Primary outcome was the incremental cost-effectiveness ratio (ICER) for VLP compared with EF. Data regarding health effects (Quality-adjusted life years, QALYs) was prospectively collected during the trial period until 3 years after surgery. Cost data was collected retrospectively for the same time period and included direct and indirect costs (production loss).ResultsOne hundred and thirteen patients (VLP n = 58, EF n = 55) had complete data until 3 years and were used in the analysis. At one year, the VLP group had a mean incremental cost of 878 euros and a gain of 0.020 QALYs compared with the EF group, rendering an ICER of 43 900 euros per QALY. At three years, the VLP group had a mean incremental cost of 1 082 euros and a negative incremental effect of -0.005 QALYs compared to the EF group, which means that VLP was dominated by EF. The probability that VLP was cost-effective compared to EF at three years, was lower than 50% independent of the willingness to pay per QALY.ConclusionThree years after distal radius fracture surgery, VLP fixation resulted in higher costs and a smaller effect in QALYs compared to EF. Our results indicate that it is uncertain if VLP is a cost-effective treatment of unstable distal radius fractures compared to EF.
| S-EPMC7544026 | biostudies-literature
Project description:BackgroundOf all distal radius fractures, 25 % are complete articular fractures (AO/OTA type C fractures). Two thirds of those fractures are displaced and require reduction. According to several International Guidelines, adequately reduced intra-articular distal radius fractures are best treated non-operatively with plaster immobilisation, while surgical fixation is suggested only when the articular step exceeds 2 mm after reduction. However, these recommendations are based on studies that did not differentiate between intra- and extra-articular distal radius fractures. Thus, no clear consensus about the best treatment for patients with displaced intra-articular distal radius fractures can be reached. Despite the lack of evidence, an increase in internal fixation of intra-articular distal radius fractures has been observed over the last decade. The aim of this study is to determine the difference in functional outcome following open reduction and plate fixation compared with non-operative treatment with closed reduction and plaster immobilisation in patients with a displaced intra articular distal radius fracture.Methods/designThis multicentre randomised controlled trial will randomise between open reduction and internal plate fixation (intervention group) and closed reduction and plaster immobilisation (control group). All consecutive adult patients from 18 to 65 years with a displaced intra-articular distal radius fracture (AO/OTA type C), which has been adequately reduced at the Emergency Department according to the Dutch National Guidelines, are eligible for inclusion in this study. The primary outcome is function and pain of the wrist assessed with the Patient-Rated Wrist Evaluation score (PRWE). Secondary outcomes are the Disability of the Arm, Shoulder and Hand score (DASH), pain, quality of life (SF-36), range of motion, grip strength, radiological parameters, complications, crossovers and cost-effectiveness of both treatments. A total of 90 patients will be included in this study.DiscussionAlthough displaced intra-articular distal radius fractures are common, there is still no evidence on the optimal treatment for these fractures in patients aged 18 to 65 years. Therefore we aim to determine the difference in functional outcome between open reduction and plate fixation and closed reduction and plaster immobilisation.Trial registrationThis study is registered at ClinicalTrials.gov ( NCT02651779 ) on January 4(th) 2016.
| S-EPMC4748545 | biostudies-literature
Project description:INTRODUCTION: Intra-articular distal radius fractures with volar and dorsal comminution present a special challenge to the hand surgeon. METHODS: Ten patients formed the study cohort. All plates were low profile and stainless steel. Radiographic parameters, range of motion, and strength compared to the uninjured side were recorded. Functional outcome was evaluated by Disabilities of the Arm, Shoulder and Hand (DASH) questionnaire and Gartland and Werley scoring system. RESULTS: Median age at surgery was 58 years (range, 24 to 86). Mean follow-up was 17 months (range, 12 to 28). According to the AO classification system, there were three type C2 and seven type C3 fractures. Median preoperative dorsal angulation was 24 deg; median postoperative dorsal angulation was 3 deg. Eighty percent (8) of the fractures also had an intra-articular step-off or gap, all of which were corrected to neutral by the procedure. Compared with the contralateral side, mean extension and flexion were 73 and 75%, respectively, pronation and supination were 95 and 88%, respectively, and grip strength and thumb pinch were 72 and 87%, respectively. Mean postoperative DASH score was 16 points, and 70% (7) of the patients had Gartland and Werley scores of good or excellent. None of the patients needed to have their plates removed, and no extensor tendon rupture was reported. CONCLUSIONS: The "sandwich" plating technique is an effective method of regaining near-anatomic reconstruction of intra-articular, volarly and dorsally comminuted distal radius fractures. Results from this study demonstrate that patients can expect to regain about 80% of their range of motion and strength. Moreover, 70% of the patients will have good to excellent functional outcomes. This is the first study to examine range of motion and functional outcome of low-profile "sandwich" plating without plate removal.
| S-EPMC2528974 | biostudies-other
Project description:Background The purpose of this study is to optimize conservative treatment of distal radius and scaphoid fracture, in terms of comfort, fracture stabilization, and prevention of cast complications. Description of Technique Advances in additive manufacturing have allowed the development of patient-specific anatomical braces (PSABs) which have the potential to fulfill this purpose. Our specific aims were to develop a model of PSAB, adapted to fracture care, to evaluate if this brace would be well tolerated by healthy volunteers and to determine its mechanical properties as compared with conventional methods of wrist immobilization. Materials and Methods Several three-dimensional-printed splint prototypes were designed by mechanical engineers based on surgeons' and hand therapists' clinical expertise. These experimental braces underwent testing in a preclinical study involving 10 healthy volunteers, assessing comfort, satisfaction, and activities. The final prototype was mechanically compared with a conventional cast and a prefabricated splint, testing different closing systems. A mathematical algorithm was created to automatically adapt the final PSAB model to the patient's anatomy. Results The final prototype achieved an overall satisfaction score of 79%, weighing less than 90 g, made from polyamide, and fixed using hook and loop straps. The PSAB stiffness varied between 0.64 and 0.99 Nm/degree, surpassing the performance of both conventional plaster casts and prefabricated splints. Conclusion The final wrist PSAB model, adapted for fracture treatment, is lightweight, comfortable, and provides anatomical contention. It is currently being tested for the treatment of stable distal radius and scaphoid fractures in comparison to conventional plaster cast.
| S-EPMC11407844 | biostudies-literature