Influence of fluorescent dopants on the vat photopolymerization of acrylate-based plastic scintillators for application in neutron/gamma pulse shape discrimination
Ontology highlight
ABSTRACT:
SUBMITTER: Chandler C
PROVIDER: S-EPMC10502904 | biostudies-literature | 2023 Jul
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:As an energy-efficient additive manufacturing process, vat photopolymerization 3D-printing has become a convenient technology to fabricate functional devices with high resolution and freedom in design. However, due to their permanently crosslinked network structure, photopolymers are not easily reprocessed or repaired. To improve the environmental footprint of 3D-printed objects, herein, we combine the dynamic nature of hydroxyl ester links, undergoing a catalyzed transesterification at elevated temperature, with an acrylate monomer derived from renewable resources. As a sustainable building block, we synthesized an acrylated linseed oil and mixed it with selected thiol crosslinkers. By careful selection of the transesterification catalyst, we obtained dynamic thiol-acrylate resins with a high cure rate and decent storage stability, which enabled the digital light processing (DLP) 3D-printing of objects with a structure size of 550 µm. Owing to their dynamic covalent bonds, the thiol-acrylate networks were able to relax 63% of their initial stress within 22 min at 180 °C and showed enhanced toughness after thermal annealing. We exploited the thermo-activated reflow of the dynamic networks to heal and re-shape the 3D-printed objects. The dynamic thiol-acrylate photopolymers also demonstrated promising healing, shape memory, and re-shaping properties, thus offering great potential for various industrial fields such as soft robotics and electronics.
| S-EPMC9784638 | biostudies-literature
Project description:Polydimethylsiloxane (PDMS) or silicone elastomers have garnered considerable attention in the field of medical device applications due to their superior thermal stability. However, conventional manufacturing techniques for silicone elastomers suffer from drawbacks such as cost, lengthy production time, and inherent difficulties in fabricating complex structures. To address these limitations, photosensitive polydimethylsiloxane urethane methacrylate (PDMSUMA) oligomers were synthesized, and their curing behaviors were specifically investigated for vat photopolymerization 3D printing applications. The study focused on exploring the impact of weight ratios between poly(ethylene glycol) dimethacrylate (PEGDMA) and 2-hydroxyethyl methacrylate (HEMA) in the PDMSUMA resin formulation. The addition of PEGDMA as a reactive diluent was found to enhance the printability of the PDMSUMA resin and decrease its viscosity. Thermal, mechanical, and shape memory properties of the 3D-printed specimens were examined. Our findings demonstrate the potential of PDMSUMA resins for developing customizable shape memory materials with tailored properties.
| S-EPMC10795029 | biostudies-literature
Project description:In this study, multifunctional Fresnel lenses were explored as a potential solution for correcting vision in patients with color vision deficiency (CVD) and high myopia. Current studies have primarily focused on color vision correction through the 3D printing of glasses and contact lenses. However, the potential of 3D-printed multifunctional devices, such as Fresnel lenses, goes beyond addressing a single vision correction issue. For this study, computer-aided design (CAD) model of Fresnel lens with high diopter based on constant height configuration was developed. The CAD model was successfully fabricated using vat photopolymerization 3D printer, employing laboratory-prepared transparent HEMA resin. The resin was modified with two Atto dyes (565 nm and 488 nm), known for their ability to filter out problematic wavelengths (400-500 nm and 540-580 nm) to address color vision deficiency. The printed lenses were characterized by their chemical, physical, and optical properties using various characterization techniques. The focusing performance was evaluated using focal length measurements, and the results obtained were less than 2 mm deviation from the design value, having the potential to assist in higher myopic vision correction. The resulting optical spectra were compared with commercial glasses, revealing close agreement for CVD correction. These results expand the potential applications of multifunctional Fresnel lenses in ophthalmology, demonstrating their effectiveness as vision-correcting lenses and imaging systems.
| S-EPMC11493721 | biostudies-literature
Project description:While vat photopolymerization has many advantages over soft lithography in fabricating microfluidic devices, including efficiency and shape complexity, it has difficulty achieving well-controlled micrometer-sized (smaller than 100 μm) channels in the layer building direction. The considerable light penetration depth of transparent resin leads to over-curing that inevitably cures the residual resin inside flow channels, causing clogs. In this paper, a 3D printing process - in-situ transfer vat photopolymerization is reported to solve this critical over-curing issue in fabricating microfluidic devices. We demonstrate microchannels with high Z-resolution (within 10 μm level) and high accuracy (within 2 μm level) using a general method with no requirements on liquid resins such as reduced transparency nor leads to a reduced fabrication speed. Compared with all other vat photopolymerization-based techniques specialized for microfluidic channel fabrication, our universal approach is compatible with commonly used 405 nm light sources and commercial photocurable resins. The process has been verified by multifunctional devices, including 3D serpentine microfluidic channels, microfluidic valves, and particle sorting devices. This work solves a critical barrier in 3D printing microfluidic channels using the high-speed vat photopolymerization process and broadens the material options. It also significantly advances vat photopolymerization's use in applications requiring small gaps with high accuracy in the Z-direction.
| S-EPMC8854570 | biostudies-literature
Project description:Vat photopolymerization typically prints highly crosslinked networks. Printing hydrogels, which are also networks but with a high swelling capacity in water and therefore with low crosslinking density, is a challenge for this technique. However, it may be of interest in medicine and in other areas, since it would allow for the preparation of this type of 3D-shaped material. In this work, an approach for printing hydrogels via vat photopolymerization that uses a mixture of stable and hydrolysable crosslinkers has been evaluated so that an initial highly crosslinked network can be printed, although after hydrolysis it becomes a network with low crosslinking. This approach has been studied with PEO/PEG-related formulations, that is, with a PEG-dimethacrylate as a stable crosslinker, a PEO-related derivative carrying β-aminoesters as a degradable crosslinker, and PEG-methyl ether acrylate and hydroxyethyl acrylate as monofunctional monomers. A wide family of formulations has been studied, maintaining the weight percentage of the crosslinkers at 15%. Resins have been studied in terms of viscosity, and the printing process has been evaluated through the generation of Jacobs working curves. It has been shown that this approach allows for the printing of pieces of different shapes and sizes via vat photopolymerization, and that these pieces can re-ajust their water content in a tailored fashion through treatments in different media (PBS or pH 10 buffer).
| S-EPMC10452991 | biostudies-literature
Project description:The possibility to detect fast neutrons as a distinct signal from that one of γ-rays background is surely of great importance for several topics, spanning from homeland security to radiation monitoring in nuclear physics research plants. Nowadays, Helium-3 based detectors are extremely expensive, while the use of large volume liquid scintillators presents serious concerns related to spillage risks and waste disposal. A very attractive alternative is the use of commercially available solid scintillators, which exploits an aromatic polymer matrix entrapping very high loadings of primary dye, thereby enabling the use of pulse shape analysis (PSA) to discriminate between fast neutrons and γ-rays. In this work, we analyse in detail the optical features of a solid scintillator composed by polymethylphenylsiloxane (PMPS) as base polymer loaded with moderate amounts of 2,5-diphenyloxazole (PPO). Furthermore, fluorescence decay kinetics have been correlated to the observed pulse shape discrimination capabilities of this radiation and thermally resistant scintillator, whose performances have been discussed in terms of conformational features and excimers formation revealed by the optical analyses.
| S-EPMC6591301 | biostudies-literature
Project description:We report on the wavelength-selective photopolymerization of a hybrid acrylate-oxetane cholesteric liquid crystal monomer mixture. By controlling the sequence and rate of the orthogonal free-radical and cationic photopolymerization reactions, it is possible to control the degree of phase separation in the resulting liquid crystal interpenetrating networks. We show that this can be used to tune the reflective color of the structurally colored coatings produced. Conversely, the structural color can be used to monitor the degree of phase separation. Our new photopolymerization procedure allows for structuring liquid crystal networks in three dimensions, which has great potential for fabricating liquid crystal polymer materials with programmable functional properties.
| S-EPMC8252527 | biostudies-literature
Project description: Not available
| S-EPMC11205379 | biostudies-literature
Project description:The working curve informs resin properties and print parameters for stereolithography, digital light processing, and other photopolymer additive manufacturing (PAM) technologies. First demonstrated in 1992, the working curve measurement of cure depth vs radiant exposure of light is now a foundational measurement in the field of PAM. Despite its widespread use in industry and academia, there is no formal method or procedure for performing the working curve measurement, raising questions about the utility of reported working curve parameters. Here, an interlaboratory study (ILS) is described in which 24 individual laboratories performed a working curve measurement on an aliquot from a single batch of PAM resin. The ILS reveals that there is enormous scatter in the working curve data and the key fit parameters derived from it. The measured depth of light penetration Dp varied by as much as 7x between participants, while the critical radiant exposure for gelation Ec varied by as much as 70x. This significant scatter is attributed to a lack of common procedure, variation in light engines, epistemic uncertainties from the Jacobs equation, and the use of measurement tools with insufficient precision. The ILS findings highlight an urgent need for procedural standardization and better hardware characterization in this rapidly growing field.
| S-EPMC10986335 | biostudies-literature
Project description:The material properties and processing of investment casting patterns manufactured using conventional wax injection Molding and those manufactured by vat photopolymerization can be substantially different in terms of thermal expansion and mechanical properties, which can generate problems with dimensional accuracy and stability before and during ceramic shelling and shell failures during the burn-out of the 3D printed casting patterns. In this paper and for the first time, the monofunctional Acryloyl morpholine monomer was used for 3D printing of casting patterns, due to its thermoplastic-like behavior, e.g., softening by heat. However, the hydrophilic behavior of this polymer led to an incorporation of up to 60 wt% of Hexanediol diacrylate, to control the water absorption of the network, which to some extent, compromised the softening feature of Acryloyl morpholine. Addition of a powdered wax filler resulted in a delayed thermal decomposition of the polymer network, however, it helped to reduce the thermal expansion of the parts. The dimensional accuracy and stability of the wax-filled formulation indicated an excellent dimensional tolerance of less than ±130 µm. Finally, the 3D printed patterns successfully went through a burn out process with no damages to the ceramic shell.
| S-EPMC9656478 | biostudies-literature