Catalytic depolymerization of Kraft lignin to high yield alkylated-phenols over CoMo/SBA-15 catalyst in supercritical ethanol† † Electronic supplementary information (ESI) available. See DOI: https://doi.org/10.1039/d3ra05018a
Ontology highlight
ABSTRACT:
SUBMITTER: Rana M
PROVIDER: S-EPMC10570907 | biostudies-literature | 2023 Oct
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Cyclohexanol and its derivatives are widely used as chemical intermediates and fuel additives. Herein, Ru/SBA-15 catalysts were prepared via impregnation, and used for the production of cyclohexanols from lignin-derived phenols. The catalyst samples were characterized by XRD, XPS, TEM, etc., where the Ru0 species was speculated as the active phase. 5 wt% Ru/SBA-15 with small Ru particle size (4.99 nm) and high Ru dispersion (27.05%) exhibited an excellent hydrogenation activity. A high cyclohexanol yield of >99.9% was achieved at 20 °C for 5 h in an aqueous phase, and the catalyst indicated stable activity and selectivity after five runs. Crucially, Ru/SBA-15 exhibited a zero-order reaction rate with an apparent activation energy (Ea) as low as 10.88 kJ mol-1 and a TON of 172.84 at 80 °C. Simultaneously, demethoxylation activity was also observed in the hydrodeoxygenation (HDO) of G- and S-type monophenols, and a high yield of 37.4% of cyclohexanol was obtained at 80 °C and 4 h when using eugenol as substrate.
| S-EPMC8985087 | biostudies-literature
Project description:The purpose of this study is to modify lignin for better blending with general purpose synthetic polymers. The possible advantages by using this modification would be cost reduction, better physical properties, and biodegradability. In this study, butyrolactone-modified lignin (BLL) and tetrahydrofuran-modified lignin (THFL) were used for aliphatic chain modification of lignin using an acid-catalyzed esterification method in order to mimic the relation of lignin-carbohydrate-complex (LCC) and cellulose. The results of several analyses indicated that lignin was well modified. It was confirmed that the lignin was modified as expected and the reaction sites of the modification, as well as the reaction behaviors, were varied by the reagent types. The result of X-ray diffraction analysis (XRD) analysis indicated that modified lignin/polymer blends increased the crystallinity due to their good compatibility. It can be confirmed that the type of alkyl chain and the miscibility gap between the alkyl chain-matrix affected the mechanical properties enormously in the fungi-degradable environment. From this study, a new method of lignin modification is proposed, and it is found that modified lignin retains the property of the substituted aliphatic chain well. This method could be a proper lignin modification method.
| S-EPMC5509268 | biostudies-other
Project description:Lignin is a potential resource for biobased aromatics with applications in the field of fuel additives, resins, and bioplastics. Via a catalytic depolymerization process using supercritical ethanol and a mixed metal oxide catalyst (CuMgAlOx), lignin can be converted into a lignin oil, containing phenolic monomers that are intermediates to the mentioned applications. Herein, we evaluated the viability of this lignin conversion technology through a stage-gate scale-up methodology. Optimization was done with a day-clustered Box-Behnken design to accommodate the large number of experimental runs in which five input factors (temperature, lignin-to-ethanol ratio, catalyst particle size, catalyst concentration, and reaction time) and three output product streams (monomer yield, yield of THF-soluble fragments, and yield of THF-insoluble fragments and char) were considered. Qualitative relationships between the studied process parameters and the product streams were determined based on mass balances and product analyses. Linear mixed models with random intercept were employed to study quantitative relationships between the input factors and the outcomes through maximum likelihood estimation. The response surface methodology study reveals that the selected input factors, together with higher order interactions, are highly significant for the determination of the three response surfaces. The good agreement between the predicted and experimental yield of the three output streams is a validation of the response surface methodology analysis discussed in this contribution.
| S-EPMC10241191 | biostudies-literature
Project description:BackgroundLignin is a potential feedstock for microbial conversion into various chemicals. However, the microbial degradation rate of native or technical lignin is low, and chemical depolymerization is needed to obtain reasonable conversion rates. In the current study, nine bacterial strains belonging to the Pseudomonas and Rhodococcus genera were evaluated for their ability to grow on alkaline-treated softwood lignin as a sole carbon source.ResultsPseudomonas fluorescens DSM 50090 and Rhodococcus opacus DSM1069 showed the best growth of the tested species on plates with lignin. Further evaluation of P. fluorescens and R. opacus was made in liquid cultivations with depolymerized softwood Kraft lignin (DL) at a concentration of 1 g/L. Size-exclusion chromatography (SEC) showed that R. opacus consumed most of the available lower-molecular weight compounds (approximately 0.1-0.4 kDa) in the DL, but the weight distribution of larger fractions was almost unaffected. Importantly, the consumed compounds included guaiacol-one of the main monomers in the DL. SEC analysis of P. fluorescens culture broth, in contrast, did not show a large conversion of low-molecular weight compounds, and guaiacol remained unconsumed. However, a significant shift in molecular weight distribution towards lower average weights was seen after cultivation with P. fluorescens.ConclusionsRhodococcus opacus and P. fluorescens were identified as two potential microbial candidates for the conversion/consumption of base-catalyzed depolymerized lignin, acting on low- and high-molecular weight lignin fragments, respectively. These findings will be of relevance for designing bioconversion of softwood Kraft lignin.
| S-EPMC6420747 | biostudies-literature
Project description:BackgroundLignin is a potential feedstock for microbial conversion into various chemicals. However, the degradation rate of native or technical lignin is low, and depolymerization is needed to obtain reasonable conversion rates. In the current study, base-catalyzed depolymerization-using NaOH (5 wt%)-of softwood Kraft lignin was conducted in a continuous-flow reactor system at temperatures in the range 190-240 °C and residence times of 1 or 2 min. The ability of growth of nine bacterial strains belonging to the genera Pseudomonas and Rhodococcus was tested using the alkaline-treated lignin as a sole carbon source.ResultsPseudomonas fluorescens and Rhodococcus opacus showed the best growth of the tested species on plates with lignin. Further evaluation of P. fluorescens and R. opacus was made in liquid cultivations with depolymerized lignin (DL) at a concentration of 1 g/L. Size exclusion chromatography (SEC) showed that R. opacus consumed most of the available lower molecular weight compounds (approximately 0.1-0.4 kDa) in the DL, but the weight distribution of larger fractions was almost unaffected. Importantly, the consumed compounds included guaiacol-one of the main monomers in the DL. SEC analysis of P. fluorescens culture broth, in contrast, did not show a large conversion of low molecular weight compounds, and guaiacol remained unconsumed. However, a significant shift in molecular weight distribution towards lower average weights was seen.ConclusionsRhodococcus opacus and P. fluorescens were identified as two potential microbial candidates for the conversion/consumption of base-catalyzed depolymerized lignin, acting on low and high molecular weight lignin fragments, respectively. These findings will be of relevance for designing bioconversion of softwood Kraft lignin.
| S-EPMC6123935 | biostudies-literature
Project description:The lignin-first biorefinery method appears to be an attractive approach to produce phenolic chemicals. Herein, corn stover was employed for the production of phenolic monomers using an unsupported non-noble MoS2 catalyst. The yield of phenolic monomers was enhanced from 6.65% to 18.47% with MoS2 at 250 °C and about 75% lignin was degraded with more than 90% glucan reserved in the solid residues. The Fourier-Transform Infrared (FT-IR) and heteronuclear single quantum coherence-nuclear magnetic resonance (1H-13C HSQC-NMR) characterization suggested that the cleavage of the β-O-4, γ-ester and benzyl ether linkages were enhanced, promoting the delignification and the depolymerization of lignin. The catalyst performance was relatively effective with 14.30% phenolic monomer yield after the fifth run. The effects of the reaction temperature, the initial hydrogen pressure, the dosage of catalyst, and the reaction time were investigated. The model reactions were also proposed for the potential mechanism study. This work provides some basic information for the improvement of the graminaceous plant lignin-first process with a non-noble metal catalyst.
| S-EPMC9077037 | biostudies-literature
Project description:Non-noble bimetallic NiMo supported on zeolitic imidazolate framework-derived porous carbon (NiMo@FDC) catalyst for lignin depolymerization has been successfully developed. The synergism between Ni and Mo species in NiMo@FDC catalyst could promote the catalytic cleavage of C-O linkages in Kraft lignin. At a low reaction temperature of 240 °C and under 4 MPa H2, the lignin liquefaction yield was 98.85 wt% and minimum coke yield was 1 wt%, particularly when using 10%NiMo@FDC catalyst. Additionally, at a high reaction temperature of 300 °C and under 2 MPa H2, there was an overall yield of 86 wt% of liquid product and 42 wt% of petroleum ether soluble product. The higher heating value (HHV) increased from 27.65 MJ kg-1 to 34.11 MJ kg-1. In the cycling experiment, the bifunctional catalyst also demonstrated reversability and stability. The synergy of Ni hydrogenation sites and Mo coupled adsorption sites identified a possible mechanism path, which could offer considerable potential for lignin depolymerization.
| S-EPMC9044013 | biostudies-literature
Project description:Recently, electro-oxidation of kraft lignin has been reported as a prominent electrochemical reaction to generate hydrogen at lower overpotential in alkaline water electrolysis. However, this reaction is highly limited by the low performance of existing electrocatalysts. Herein, we report a novel yet effective catalyst that comprises nonprecious trimetallic (Ni, Fe, and Co) nanoalloy as a core in a phosphidated nitrogen-doped carbon shell (referred to as sample P-NiFeCo/NC) for efficient electro-oxidation of kraft lignin at different temperatures in alkaline medium. The as-synthesized catalyst electro-oxidizes lignin only at 0.2 V versus Hg/HgO, which is almost three times less positive potential than in the conventional oxygen evolution reaction (0.59 V versus Hg/HgO) at 6.4 mA/cm2 in 1 M KOH. The catalyst demonstrates a turnover frequency (TOF) three to five times greater in lignin containing 1 M KOH than that of pure 1 M KOH. More importantly, the catalyst P-NiFeCo/NC shows theoretical hydrogen production of about 0.37 μmoles/min in the presence of lignin, much higher than that in pure 1 M KOH (0.0078 μ moles/min). Thus, this work verifies the benefit of the NiFeCo nanoalloy incorporated in carbon matrix, providing the way to realize a highly active catalyst for the electro-oxidation of kraft lignin.
| S-EPMC9503039 | biostudies-literature
Project description:Lignin is a recalcitrant and underexploited natural feedstock for aromatic commodity chemicals, and its degradation generally requires the use of high temperatures and harsh reaction conditions. Herein we present an ambient temperature one-pot process for the controlled oxidation and depolymerization of this potent resource. Harnessing the potential of electrocatalytic oxidation in conjugation with our photocatalytic cleavage methodology, we have developed an operationally simple procedure for selective fragmentation of β-O-4 bonds with excellent mass recovery, which provides a unique opportunity to expand the existing lignin usage from energy source to commodity chemicals and synthetic building block source.
| S-EPMC5492418 | biostudies-literature
Project description:The valorization of lignin that derives as by product in various biomass conversion processes has become a major research and technological objective. The potential of the production of valuable mono-aromatics (BTX and others) and (alkyl)phenols by catalytic fast pyrolysis of lignin is investigated in this work by the use of ZSM-5 zeolites with different acidic and porosity characteristics. More specifically, conventional microporous ZSM-5 (Si/Al = 11.5, 25, 40), nano-sized (≤20 nm, by direct synthesis) and mesoporous (9 nm, by mild alkaline treatment) ZSM-5 zeolites were tested in the fast pyrolysis of a softwood kraft lignin at 400-600°C on a Py/GC-MS system and a fixed-bed reactor unit. The composition of lignin (FT-IR, 2D HSQC NMR) was correlated with the composition of the thermal (non-catalytic) pyrolysis oil, while the effect of pyrolysis temperature and catalyst-to-lignin (C/L) ratio, as well as of the Si/Al ratio, acidity, micro/mesoporosity and nano-size of ZSM-5, on bio-oil composition was thoroughly investigated. It was shown that the conventional microporous ZSM-5 zeolites are more selective toward mono-aromatics while the nano-sized and mesoporous ZSM-5 exhibited also high selectivity for (alkyl)phenols. However, the nano-sized ZSM-5 zeolite exhibited the lowest yield of organic bio-oil and highest production of water, coke and non-condensable gases compared to the conventional microporous and mesoporous ZSM-5 zeolites.
| S-EPMC6058026 | biostudies-literature