Project description:Harvesting energy from natural water evaporation has been proposed as a promising alternative to supply power for self-powered and low-power devices and systems, owing to its spontaneous, ubiquitous, and sustainability. Herein, an approach is presented for harvesting water-evaporation-induced electricity based on liquid-solid triboelectric nanogenerators (LS-TENGs), which has various advantages of easy preparation, substrate needless, and robustness. This developed harvester with porous Al2 O3 ceramic sheet can generate a continuous and stable direct current of ≈0.3 µA and voltage of ≈0.7 V by optimizing the sheet physical dimensions and ambient parameters such as relative humidity, temperature, wind velocity, and ion concentration. The output power also can be improved significantly by series or parallel connection the harvesters, which has superior electrical compatibility and environmental suitability. The development of the water-evaporation-induced electricity harvesting shows many application prospects including power supply for digital calculator and charging capacitor. This research provides an in-depth experimental study on water-evaporation-induced electricity harvesting based on LS-TENGs and an efficient approach to supply electricity for low-power devices.
Project description:Triboelectric nanogenerators with the function of harvesting human motion energy have attracted wide attention. Here, we demonstrate a shared-electrode and nested-tube structure triboelectric nanogenerator (SNTN) for harvesting human motion energy. The design of the SNTN employs flexible silicone rubber as the negative friction material and Ni-coated polyester conductive textile as the positive friction material and the electrode material. The entire structure consists of an inner triboelectric unit and an outer triboelectric unit. The inner triboelectric unit is formed by a hollow inner tube and a hollow middle tube, while the hollow middle tube and a hollow outer tube constitute the outer triboelectric unit. The hollow middle tube is used as the shared tube, and the electrode in the middle tube is used as the shared electrode of the two triboelectric units. Our research demonstrates that the output performance of the SNTN was improved significantly compared with a single triboelectric unit due to the cooperation of the two triboelectric units. When the SNTN is pressed by 300 N external force, output open-circuit voltage of 180 V and output short-circuit current of 8.5 μA can be obtained. The output electrical energy can light up 31 light-emitting diodes (LEDs) connected serially (displaying "XZTC") and can drive a digital clock after rectifying storage, which shows application prospects in the field of illuminating devices and portable electronics.
Project description:As a new energy harvesting technology, triboelectric nanogenerators are widely used for vibration mechanical energy harvesting. However, the current schemes ignore the composite characteristics of vibration, with problems such as utilization and low collection efficiency. In this paper, a random resonance cantilever beam triboelectric nanogenerator (RCB-TENG) with dual-mode coupled is presented, the working mode is a coupling form of in-plane sliding and vertical contact-separation that can effectively collect complex vibration energy in transverse and longitudinal directions. The influences of the structural parameters of the RCB-TENG and different dielectric materials on the output performance are systematically investigated. The single vibration module achieved a power density of 463.56 mW/m2 and a transfer charge of 10.7 μC at a vibration frequency of 46 Hz, an increase in power density, and a transfer charge of 4.94 and 3.82 times, respectively, compared to the conventional contact-separation mode. Finally, the RCB-TENG was tested in practice, and it was observed that nine 1 W commercial LED bulbs and 500 5 mm diameter LED lamps were successfully lit. This work offers new ideas for distributed energy harvesting technologies and holds broad promise in the field of energy harvesting from wind, water, wave, and random vibrations caused by mechanical energy.
Project description:The environmentally friendly harvesting of wind energy is an effective technique for achieving carbon neutrality and a green economy. In this work, a core-shell triboelectric nanogenerator (CS-TENG) for harvesting wind energy is demonstrated and the device structure parameters are optimized. The core-shell structure enables the CS-TENG to respond sensitively to wind from any direction and generate electrical output on the basis of the vertical contact-separation mode. A single device can generate a maximum power density of 0.14 W/m3 and can power 124 light-emitting diodes. In addition, wind energy can be harvested even at a wind speed as low as 2.3 m/s by paralleling CS-TENGs of different sizes. Finally, a self-powered water quality testing system that uses the CS-TENG as its power supply is built. The CS-TENG exhibits the advantages of a simple structure, environmentally friendly materials, low cost, and simple fabrication process. These features are of considerable significance for the development of green energy harvesting devices.
Project description:The arch-shaped single electrode based triboelectric nanogenerator (TENG) is fabricated using thin film of reduced graphene oxide nanoribbons (rGONRs) with polyvinylidene fluoride (PVDF) polymer used as binder to effectively convert mechanical energy into electrical energy. The incorporation of rGONRs in PVDF polymer enhances average surface roughness of rGONRs/PVDF thin film. With the combination of the enhancement of average roughness and production of functional groups, which indicate improve charge storage capacity of prepared film. Furthermore, the redox peaks obtained through cyclic voltammetry were identified more in rGONRs/PVDF composite in comparison to pristine rGONRs to confirm charge transfer capability of film. Herein, the output performance was discussed experimentally as well as theoretically, maximum voltage was obtained to be 0.35 V. The newly designed TENG to harvest mechanical energy and opens up many new avenues of research in the energy harvesting applications.
Project description:Triboelectric nanogenerators (TENG) have shown great potential in harvesting energy from water. For the TENG that harvests water energy, surface hydrophobicity is crucial for its performance. In this paper, we prepare a hydrophobic composite film of Polyvinylidene Fluoride/Polydimethylsiloxane/Polytetrafluoroethylene (PVDF/PDMS/PTFE) and an electrode of Polyaniline/Carbon nanotubes/Silver nanowires (PANI/CNTs/AgNWs) by electrospinning technology and a doping method, respectively, which are served as the friction layer and top electrode of TENG. The contact angle of the hydrophobic film and electrode both reach over 120°, which makes the separation process between water and the interface complete and promotes the output of TENG. The open-circuit voltage (Voc) and short-circuit current (Isc) can reach 150 V and 60 μA approximately. In addition, the composite electrode can be applied in the preparation of complex electrode shapes. Furthermore, the different reactions of TENG to different liquids indicate that it may contribute to liquid-type sensing systems. This work presents an efficient approach to fabricating hydrophobic films and electrodes, laying a foundation for the development of TENG for harvesting water energy.
Project description:Energy converters based on vortex-induced vibrations (VIV) have shown great potential for harvesting energy from low-velocity flows, which constitute a significant portion of ocean energy. However, solid-solid triboelectric nanogenerators (TENG) are not wear-resistant in corrosive environments. Therefore, to effectively harvest ocean energy over the long term, a novel solid-liquid triboelectric nanogenerator based on vortex-induced resonance (VIV-SL-TENG) is presented. The energy is harvested through the resonance between VIV of a cylinder and the relative motions of solid-liquid friction pairs inside the cylinder. The factors that affect the output performance of the system, including the liquid mass ratio and the deflection angle of the friction plates, are studied and optimized by establishing mathematical models and conducting computational fluid dynamics simulations. Furthermore, an experimental platform for the VIV-SL-TENG system is constructed to test and validate the performance of the harvester under different conditions. The experiments demonstrate that the energy harvester can successfully convert VIV energy into electrical energy and reach maximum output voltage in the resonance state. As a new type of energy harvester, the presented design shows a promising potential in the field of 'blue energy' harvesting.
Project description:Triboelectric nanogenerators (TENGs) have potential to achieve energy harvesting and condition monitoring of oils, the "lifeblood" of industry. However, oil absorption on the solid surfaces is a great challenge for oil-solid TENG (O-TENG). Here, oleophobic/superamphiphobic O-TENGs are achieved via engineering of solid surface wetting properties. The designed O-TENG can generate an excellent electricity (with a charge density of 9.1 µC m-2 and a power density of 1.23 mW m-2), which is an order of magnitude higher than other O-TENGs made from polytetrafluoroethylene and polyimide. It also has a significant durability (30,000 cycles) and can power a digital thermometer for self-powered sensor applications. Further, a superhigh-sensitivity O-TENG monitoring system is successfully developed for real-time detecting particle/water contaminants in oils. The O-TENG can detect particle contaminants at least down to 0.01 wt% and water contaminants down to 100 ppm, which are much better than previous online monitoring methods (particle > 0.1 wt%; water > 1000 ppm). More interesting, the developed O-TENG can also distinguish water from other contaminants, which means the developed O-TENG has a highly water-selective performance. This work provides an ideal strategy for enhancing the output and durability of TENGs for oil-solid contact and opens new intelligent pathways for oil-solid energy harvesting and oil condition monitoring.
Project description:Water waves are a continuously generated renewable source of energy. However, their random motion and low frequency pose significant challenges for harvesting their energy. Herein, we propose a spherical hybrid triboelectric nanogenerator (SH-TENG) that efficiently harvests the energy of low frequency, random water waves. The SH-TENG converts the kinetic energy of the water wave into solid⁻solid and solid⁻liquid triboelectric energy simultaneously using a single electrode. The electrical output of the SH-TENG for six degrees of freedom of motion in water was investigated. Further, in order to demonstrate hybrid energy harvesting from multiple energy sources using a single electrode on the SH-TENG, the charging performance of a capacitor was evaluated. The experimental results indicate that SH-TENGs have great potential for use in self-powered environmental monitoring systems that monitor factors such as water temperature, water wave height, and pollution levels in oceans.
Project description:To combine the advantages of elastic and nonelastic triboelectric materials, this work proposes a new type of triboelectric nanogenerator (TENG) based on stacking -the stacked FKM/PU TENG. By stacking the elastomer polyurethane (PU) and the nonelastomer fluororubber (FKM), the FKM/PU TENG combines the inherent triboelectric characteristics of both materials and the unique elasticity of PU to achieve an output performance that is much higher than that of the FKM-TENG or the PU-TENG. The maximum instantaneous open-circuit voltage and short-circuit current of the FKM/PU TENG reach 661 V and 71.2 μA, respectively. Under the limiting conditions of 3 Hz and maximum compression, this device can attain a maximum power density of 49.63 W/m3 and light more than 500 LEDs. Therefore, stacking materials with different properties gives the FKM/PU TENG high output performance and great application potential, which can contribute to future development of discrete mechanical energy harvesting.