Emerging BaZrS3 and Ba(Zr,Ti)S3 Chalcogenide Perovskite Solar Cells: A Numerical Approach Toward Device Engineering and Unlocking Efficiency
Ontology highlight
ABSTRACT:
SUBMITTER:
PROVIDER: S-EPMC10832013 | biostudies-literature | 2024 Jan
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:BaZrS3, a prototypical chalcogenide perovskite, has been shown to possess a direct band gap, an exceptionally strong near band edge light absorption, and good carrier transport. Coupled with its great stability, nontoxicity with earth-abundant elements, it is thus a promising candidate for thin film solar cells. However, its reported band gap in the range of 1.7-1.8 eV is larger than the optimal value required to reach the Shockley-Queisser limit of a single-junction solar cell. Here, we report the synthesis of Ba(Zr1-x Ti x )S3 perovskite compounds with a reduced band gap. It is found that Ti-alloying is extremely effective in band gap reduction of BaZrS3: a mere 4 atom % alloying decreases the band gap from 1.78 to 1.51 eV, resulting in a theoretical maximum power conversion efficiency of 32%. Higher Ti-alloying concentration is found to destabilize the distorted chalcogenide perovskite phase.
| S-EPMC7407533 | biostudies-literature
Project description:Relaxors are complex materials with unusual properties that have been puzzling the scientific community since their discovery. The main characteristic of relaxors, that is, their dielectric relaxation, remains unclear and is still under debate. The difficulty to conduct measurements at frequencies ranging from ≃1 GHz to ≃1 THz and the challenge of developing models to capture their complex dynamical responses are among the reasons for such a situation. Here, we report first-principles-based molecular dynamic simulations of lead-free Ba(Zr0.5Ti0.5)O3, which allows us to obtain its subterahertz dynamics. This approach reproduces the striking characteristics of relaxors including the dielectric relaxation, the constant-loss behaviour, the diffuse maximum in the temperature dependence of susceptibility, the substantial widening of dielectric spectrum on cooling and the resulting Vogel-Fulcher law. The simulations further relate such features to the decomposed dielectric responses, each associated with its own polarization mechanism, therefore, enhancing the current understanding of relaxor behaviour.
| S-EPMC4822000 | biostudies-literature
Project description:The lead-free ferroelectric 0.5Ba(Zr0.2Ti0.8)O3 - 0.5(Ba0.7Ca0.3)TiO3 (BCZT) is a promising component for multifunctional multiferroics due to its excellent room temperature piezoelectric properties. Having a composition close to the polymorphic phase boundary between the orthorhombic and tetragonal phases, it deserves a case study for analysis of its potential for modern electronics applications. To obtain magnetoelectric coupling, the piezoelectric phase needs to be combined with a suitable magnetostrictive phase. In the current article, we report on the synthesis, dielectric, magnetic, and magnetoelectric characterization of a new magnetoelectric multiferroic composite consisting of BCZT as a piezoelectric phase and CoFe2O4 (CFO) as the magnetostrictive phase. We found that this material is multiferroic at room temperature and manifests a magnetoelectric effect larger than that of BaTiO3 -CoFe2O4 bulk composites with similar content of the ferrite phase.
| S-EPMC4995375 | biostudies-literature
Project description:Tin-based perovskite solar cells have garnered attention for their biocompatibility, narrow bandgap, and long thermal carrier lifetime. However, nip-type tin-based perovskite solar cells have underperformed largely due to the indiscriminate use of metal oxide electron transport layers originally designed for nip-type lead-based perovskite solar cells. Here, we reveal that this underperformance is caused by oxygen vacancies and deeper energy levels in metal oxide. To address these issues, we propose a metal chalcogenide electron transport layer, specifically Sn(S0.92Se0.08)2, which circumvents the oxygen molecules desorption and impedes the Sn2+ oxidation. As a result, tin-based perovskite solar cells with Sn(S0.92Se0.08)2 demonstrate a VOC increase from 0.48 - 0.73 V and a power conversion efficiency boost from 6.98 - 11.78%. Additionally, these cells exhibit improved stability, retaining over 95% of their initial efficiency after 1632 h. Our findings showcase metal chalcogenides as promising candidates for future nip-type tin-based perovskite solar cell applications.
| S-EPMC11530694 | biostudies-literature
Project description:In light of directives around the world to eliminate toxic materials in various technologies, finding lead-free materials with high piezoelectric responses constitutes an important current scientific goal. As such, the recent discovery of a large electromechanical conversion near room temperature in (1-x)Ba(Zr0.2Ti0.8)O3-x(Ba0.7Ca0.3)TiO3 compounds has directed attention to understanding its origin. Here, we report the development of a large-scale atomistic scheme providing a microscopic insight into this technologically promising material. We find that its high piezoelectricity originates from the existence of large fluctuations of polarization in the orthorhombic state arising from the combination of a flat free-energy landscape, a fragmented local structure, and the narrow temperature window around room temperature at which this orthorhombic phase is the equilibrium state. In addition to deepening the current knowledge on piezoelectricity, these findings have the potential to guide the design of other lead-free materials with large electromechanical responses.
| S-EPMC5481827 | biostudies-literature
Project description:Electrochromic devices can modulate their light absorption under a small driving voltage, but the requirement for external electrical supplies causes response-lag. To address this problem, self-powered electrochromic devices have been studied recently. However, insensitivity to the surrounding light and unsatisfactory stability of electrochromic devices have hindered their critical applications. Herein, novel perovskite solar cell-powered all-in-one gel electrochromic devices have been assembled and studied in order to achieve automatic light adjustment. Two alkynyl-containing viologen derivatives are synthesized as electrochromic materials, the devices with very high stability (up to 70000 cycles) serves as the energy storage and smart window, while the perovskite solar cell with power-conversion-efficiency up to 18.3% serves as the light detector and power harvester. The combined devices can automatically switch between bleached and colored state to adjust light absorption with variable surrounding light intensity in real-time swiftly, which establish significant potentials for applications as modern all-day intelligent windows.
| S-EPMC7881180 | biostudies-literature
Project description:Recently, the simulation of perovskite solar cells (PSCs) via SCAPS-1D has been widely reported. In this study, we adopted SCAPS-1D as a simulation tool for the numerical simulation of lead-free (Pb-free) PSCs. We used methyl ammonium germanium iodide (MAGeI3) as a light absorber, zinc oxysulphide (ZnOS) as an electron transport layer (ETL), and spiro-OMeTAD as a hole transport layer. Further, the thickness of the ZnOS, MAGeI3, and spiro-OMeTAD layers was optimized. The optimal thicknesses of the ZnOS, MAGeI3, and spiro-OMeTAD layers were found to be 100 nm, 550 nm, and 100 nm, respectively. The optimized MAGeI3-based PSCs exhibited excellent power conversion efficiency (PCE) of 21.62%, fill factor (FF) of 84.05%, and Jsc of 14.51 mA/cm2. A fantastic open circuit voltage of 1.77 V was also obtained using SCAPS-1D. We believe that these theoretically optimized parameters and conditions may help improve the experimental efficiency of MAGeI3-based PSCs in the future.
| S-EPMC9822055 | biostudies-literature
Project description:We have fabricated organic-inorganic hybrid perovskite solar cell that uses a Ti/Au multilayer as cathode and does not use electron transport materials, and achieved the highest power conversion efficiency close to 13% with high reproducibility and hysteresis-free photocurrent curves. Our cell has a Schottky planar heterojunction structure (ITO/PEDOT:PSS/perovskite/Ti/Au), in which the Ti insertion layer isolate the perovskite and Au layers, thus proving good contact between the Au and perovskite and increasing the cells' shunt resistance greatly. Moreover, the Ti/Au cathode in direct contact with hybrid perovskite showed no reaction for a long-term exposure to the air, and can provide sufficient protection and avoid the perovskite and PEDOT:PSS layers contact with moisture. Hence, the Ti/Au based devices retain about 70% of their original efficiency after 300 h storage in the ambient environment.
| S-EPMC5171770 | biostudies-literature
Project description:It is shown that the dielectric and piezoelectric properties of Ba(Ti0.8Zr0.2)O3-x(Ba0.7Ca0.3)TiO3 (x = 0.45) (BCTZ 45) epitaxial thin films have a nontrivial dependence on film thickness. BCTZ 45 epitaxial films with different thicknesses (up to 400 nm) have been deposited on SrTiO3 by pulsed laser deposition and investigated by different combined techniques: conventional and off-axis X-ray diffraction, high resolution transmission electron microscopy and dielectric and piezoforce microscopy. The changes occurring in epitaxial films when their thickness increases have been attributed to a partial relaxation of misfit strain, driving the induced tetragonal symmetry in very thin films to the original rhombohedral symmetry of the bulk material in the thickest film, which influences directly and indirectly the dielectric and piezoelectric properties.
| S-EPMC5794999 | biostudies-literature
Project description:All-inorganic metal halide perovskites are showing promising development towards efficient long-term stable materials and solar cells. Element doping, especially on the lead site, has been proved to be a useful strategy to obtain the desired film quality and material phase for high efficient and stable inorganic perovskite solar cells. Here we demonstrate a function by adding barium in CsPbI2Br. We find that barium is not incorporated into the perovskite lattice but induces phase segregation, resulting in a change in the iodide/bromide ratio compared with the precursor stoichiometry and consequently a reduction in the band gap energy of the perovskite phase. The device with 20 mol% barium shows a high power conversion efficiency of 14.0% and a great suppression of non-radiative recombination within the inorganic perovskite, yielding a high open-circuit voltage of 1.33 V and an external quantum efficiency of electroluminescence of 10-4.
| S-EPMC6794321 | biostudies-literature