Rare Earth Elements Recovery and Waste Management of Municipal Solid Waste Incineration Ash
Ontology highlight
ABSTRACT:
SUBMITTER: Wen Y
PROVIDER: S-EPMC10840445 | biostudies-literature | 2023 Nov
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:A new building filling materials (NBFM) using phosphogypsum and municipal solid waste incineration (MSWI) fly ash is prepared in this paper. The effects of MSWI fly ash dosage and MSWI fly ash water washing pretreatment on mechanical properties, setting time, metal leaching, hydration products and microstructure of NBFM are analyzed by a range of experimental studies. The results indicate that the mechanical properties, setting time and the density of micro interface of NBFM are optimal when the MSWI fly ash dosage is 3%. The mechanical properties of NBFM rise and the condensation time and leaching concentration of heavy metals decline after washing the MSWI fly ash. With the increase of the curing age, the metal element leaching of NBFM decreases, and when the curing age is 7 days, the solidification effect of NBFM on most metal elements meets the standard of Chinese code (GB5085.3-2007). The feasibility of MSWI fly ash and phosphogypsum as filling materials for building engineering is verified, and the change of macroscopic properties of NBFM is explained as well.
| S-EPMC9832018 | biostudies-literature
Project description:The main obstacle to bottom ash (BA) being used as a recycling aggregate is the content of salts and potential toxic elements (PTEs), concentrated in a layer that coats BA particles. This work presents a dry treatment for the removal of salts and PTEs from BA particles. Two pilot-scale abrasion units (with/without the removal of the fine particles) were fed with different BA samples. The performance of the abrasion tests was assessed through the analyses of particle size and moisture, and that of the column leaching tests at solid-to-liquid ratios between 0.3 and 4. The results were: the particle-size distribution of the treated materials was homogeneous (25 wt % had dimensions <6.3 mm) and their moisture halved, as well as the electrical conductivity of the leachates. A significant decrease was observed in the leachates of the treated BA for sulphates (44%), chlorides (26%), and PTEs (53% Cr, 60% Cu and 8% Mo). The statistical analysis revealed good correlations between chloride and sulphate concentrations in the leachates with Ba, Cu, Mo, and Sr, illustrating the consistent behavior of the major and minor components of the layer surrounding BA particles. In conclusion, the tested process could be considered as promising for the improvement of BA valorization.
| S-EPMC8201139 | biostudies-literature
Project description:This paper analyzes the effective use of a mixture of fly ash (MSWI-FA) and solid waste from flue gas treatment (MSWI-SW), which are by-products of the municipal waste incineration process. MSWI-FA (19 01 13*) and MSWI-SW (19 01 07*) are classified as hazardous waste due to their toxic metal content and leaching potential, and currently lack practical applications, unlike slag and bottom ash (19 01 12). This study tested these wastes as partial substitutes for natural sand within a range of 0-20% of cement mass. Statistical analysis of the experimental results allowed the creation of good quality models predicting the effect of substitution additives on compressive strength and flexural strength (correlation 0.91 and 0.93, respectively). The mixture with the highest share of substitution additives (40% = 20% + 20%) was characterized by a decrease in compressive strength by 1.3% and flexural strength by 25.8%. Cement mortars synthesized with the waste mixture (up to 20% of each component) showed slightly lower consistency and water absorption than the control mortars. After the frost resistance tests (25 cycles), the flexural and compressive strength showed ambiguous behavior, showing both increases and decreases, indicating that the percentage of waste components alone is an insufficient set of factors for predicting these strength properties. The concentration of metal ions, i.e., Zn, Cu, Pb, Ni, Cu, and Cr, in the eluate after the leaching tests did not exceed the legal levels of pollutants introduced into waters, with the exception of barium. However, its content did not exceed the permissible levels required for waste intended for landfill. Using the mixing plant for this waste in the amount of 20% each, we save about EUR 10 in the cost of purchasing sand (which is 13% of the production costs of 1 m3) and EUR 8 in the cost of environmental fees when producing 1 m3 of mortar. The proposed technology is compatible with the objectives of a sustainable economy.
| S-EPMC11818920 | biostudies-literature
Project description:Municipal solid waste incineration (MSWI) fly ash has a high concentration of heavy metals (HMs) which are hazardous to the environment. Moreover, it has high pH and buffering capacity which hinders the removal of HMs. Another constraining factor is the considerable fraction of HMs which exist in oxidizable and reducible states. The acid pretreatment of MSWI fly ash is a key solution to this problem. Therefore, the current experiment is carried out to evaluate the effect of acid pretreatment of MSWI fly ash and reaction/proposed time on the removal efficiency of HMs through an electrokinetic experiment. The leaching experiment results show that acid pretreatment has increased the desorption/release of heavy metal ions (Pb2+, Cd2+, Cu2+ and Zn2+). It enhances the migration of HM ions in electrolytic cells which get precipitated at the cathode, thereby increasing the removal efficiency of HMs in the electrokinetic experiment. Moreover, it is found that prolonged proposed time (12 d) has significant effect on the removal efficiency of HMs. Finally, it is concluded that acid pretreatment and prolonged proposed time have enhanced the removal electrokinetic remediation of HMs which is carried out via three processes, i.e. desorption (enhanced by acidification), migration and precipitation.
| S-EPMC6124067 | biostudies-literature
Project description:Waste incineration is increasingly used worldwide for better municipal solid waste management and energy recovery. However, residues resulting from waste incineration, such as Bottom Ash (BA) and Fly Ash (FA), can pose environmental and human health risks due to their physicochemical properties if not managed appropriately. On the other hand, with proper utilization, these residues can be turned into valuable Municipal metal mines. In this study, BA was granulated in various size ranges (< 0.075 mm, 0.075-0.125 mm, 0.125-0.5 mm, 0.5-1 mm, 1-2 mm, 2-4 mm, 4-16 mm, and > 16 mm). The physicochemical properties, heavy metal elements, environmental hazards, and other rare and precious metal elements in each Granulated Bottom Ash (GBA) group from Tehran's waste incineration were examined using ICP-MASS. Additionally, each GBA group's mineralogical properties and elemental composition were determined using X-ray fluorescence (XRF) and X-ray diffraction (XRD). The results showed that the average concentration of heavy metals in GBA, including Zn (1974 mg/kg), Cu, and Ba (790 mg/kg), Pb (145 mg/kg), Cr (106 mg/kg), Ni (25 mg/kg), Sn (24 mg/kg), V (25 mg/kg), As (11 mg/kg), and Sb (29 mg/kg), was higher in particles smaller than 4 mm. Precious metals such as gold (average 0.3 mg/kg) and silver (average 11 mg/kg) were significantly higher in GBA particles smaller than 0.5 mm, making their extraction economically feasible. Moreover, rare metals such as Ce, Nd, La, and Y were detected in GBA, with average concentrations of 24, 8, 11, and 7 mg/kg, respectively. The results of this study indicated that BA contains environmentally concerning metals, as well as rare and precious metals, with high concentrations, especially in particles smaller than 4 mm. This highlights the need for proper pre-treatment before using these materials in civil and municipal applications or even landfilling.
| S-EPMC10520020 | biostudies-literature
Project description:Municipal solid waste incineration (MSWI) ash is often managed through co-disposal with unburned wastes in landfills, a practice previously reported to result in enhanced leaching of pollutants (e.g., heavy metals) in landfill leachate. The objective of this study was to evaluate the effect of co-disposed unburned wastes on per- and polyfluoroalkyl substances (PFAS) in MSWI ash landfill leachate. Leachate was collected from four landfills containing MSWI ash, either as a sole waste stream or co-disposed of with sewage sludge and MSW screenings. Samples of ash and unburned materials were collected and assessed separately for leachable PFAS in the laboratory. All samples were analyzed for 26 PFAS. Results showed that greater ash content was associated with lower leachate PFAS concentrations. The pure ash monofill exhibited the lowest PFAS in landfill leachate (290 ng L-1) while the landfill contained a large amount of unburned waste had the highest PFAS (11,000 ng L-1). For laboratory leaching tests, average ∑26PFAS concentration in lab ash leachate (310 ng L-1) was 10 and 24 times lower than observed in lab sewage sludge leachate (3,200 ng L-1) and lab MSW screenings leachate (7,500 ng L-1), respectively. Leachate from the ash-only landfill had ∑26PFAS concentration similar to what was measured in the ash itself. On the contrary, ∑26PFAS concentration in co-disposal landfill leachates were similar to those in PFAS-rich unburned waste itself, regardless of the percentages of landfilled unburned wastes. We hypothesize that leachate generated in co-disposal scenarios preferentially flows through PFAS-rich unburned materials and that biotransformation of precursors enhanced by unburned waste degradation further contributes to higher concentrations of terminal PFAS in ash co-disposal sites. Landfill operators should expect PFAS in leachates to be higher when PFAS-rich unburned wastes are disposed of alongside MSWI ash, even if the unburned fraction is small.
| S-EPMC10536760 | biostudies-literature
Project description:This paper presents an experimental study on the applicability of microbial induced carbonate precipitation (MICP) to treat municipal solid waste incineration (MSWI) fly ash with high alkalinity and heavy metal toxicity. The experiments were carried out on fly ashes A and B produced from incineration processes of mechanical grate furnace and circulating fluidized bed, respectively. The results showed that both types of fly ashes contained high CaO content, which could supply sufficient endogenous Ca for MICP treatment. Moreover, S. pasteurii can survive from high alkalinity and heavy metal toxicity of fly ash solution. Further, the unconfined compressive strength (UCS) of MICP treated fly ashes A and B reached 0.385MPa and 0.709 MPa, respectively. The MICP treatment also resulted in a reduction in the leaching toxicity of heavy metals, especially for Cu, Pb and Hg. MICP had a higher solidification and stabilization effect on fly ash B, which has finer particle size and higher Ca content. These findings shone a light on the possibility of using MICP technique as a suitable and efficient tool to treat the MSWI fly ash.
| S-EPMC6797113 | biostudies-literature
Project description:Rare earth elements (REEs) are critical materials in electronics and clean technologies. With the diminishing of easily accessible minerals for mining, the REE recovery from waste is an alternative toward a circular economy. Present methods for REE recovery suffer from lengthy purifications, low extractability, and high wastewater streams. Here, we report an ultrafast electrothermal process (~3000°C, ~1 s) based on flash Joule heating (FJH) for activating wastes to improve REE extractability. FJH thermally degrades or reduces the hard-to-dissolve REE species to components with high thermodynamic solubility, leading to ~2× increase in leachability and high recovery yields using diluted acid (e.g., 0.1 M HCl). The activation strategy is feasible for various wastes including coal fly ash, bauxite residue, and electronic waste. The rapid FJH process is energy-efficient with a low electrical energy consumption of 600 kWh ton-1. The potential for this route to be rapidly scaled is outlined.
| S-EPMC8827657 | biostudies-literature
Project description:The MSWI fly ash which contains a large number of heavy metal substances is a subsidiary product of waste incineration power generation technology. If the MSWI fly ash is disposed improperly, heavy metal pollutants will pose a great threat to environmental safety and human health. Based on the technology of electrokinetic remediation, the feasibility of removing heavy metal pollutants from the MSWI fly ash using a modified electrokinetic remediation device - cylinder device was evaluated in this study. Differing from the traditional cuboid device with the volume ratio of the cathode chamber to the anode chamber being 1:1, the volume ratio of the cathode chamber to the anode chamber of the cylinder device was 16:1. Changes in parameters, such as pH values and conductivity in the cathode and the anode chambers as well as current and voltage in the sample area were analysed under the voltage gradient of 2?V/cm. After the experiment, the average removal efficiencies for Zn, Pb, Cd and Cu in the sample area were 53.2%, 31.4%, 42.3% and 30.7%, respectively. It indicates that the cylinder device is effective in removing heavy metals from the MSWI fly ash. Adopting the cylinder device for the experimental study on the electrokinetic remediation technology could provide a better way of thinking for the future engineering practices and applications.
| S-EPMC6547674 | biostudies-literature
Project description:A new technology was recently developed for municipal solid waste incineration (MSWI) fly ash stabilization, based on the employment of all waste and byproduct materials. In particular, the proposed method is based on the use of amorphous silica contained in rice husk ash (RHA), an agricultural byproduct material (COSMOS-RICE project). The obtained final inert can be applied in several applications to produce "green composites". In this work, for the first time, a process for pre-treatment of rice husk, before its use in the stabilization of heavy metals, based on the employment of Instant Pressure Drop technology (DIC) was tested. The aim of this work is to verify the influence of the pre-treatment on the efficiency on heavy metals stabilization in the COSMOS-RICE technology. DIC technique is based on a thermomechanical effect induced by an abrupt transition from high steam pressure to a vacuum, to produce changes in the material. Two different DIC pre-treatments were selected and thermal annealing at different temperatures were performed on rice husk. The resulting RHAs were employed to obtain COSMOS-RICE samples, and the stabilization procedure was tested on the MSWI fly ash. In the frame of this work, some thermal treatments were also realized in O2-limiting conditions, to test the effect of charcoal obtained from RHA on the stabilization procedure. The results of this work show that the application of DIC technology into existing treatment cycles of some waste materials should be investigated in more details to offer the possibility to stabilize and reuse waste.
| S-EPMC5455375 | biostudies-other