Investigation of NaCl-Modified Graphitic Carbon Nitride for Efficient Biodiesel Production from Waste Oil via Transesterification: A Box–Behnken Design Approach
Ontology highlight
ABSTRACT:
SUBMITTER: Hu Y
PROVIDER: S-EPMC10993245 | biostudies-literature | 2024 Mar
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Semiconductor-based photocatalysts have attracted a lot of interest due to their environmental friendliness and high stability. Waste cooking oil can be converted to biodiesel by the process of transesterification. A TiO2/g-C3N4 combination was prepared by using a wet impregnation process. The photocatalyst was analyzed by X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray spectroscopy (EDX), Thermogravimetric analysis (TGA), and Ultraviolet-visible spectroscopy (UV-vis). For effective transesterification, WCO was collected and acid-esterified to reduce the FFA concentration (below 3%). For the transesterification reaction, esterified WCO was used and the reactions were carried out under solar irradiation at 60 °C with an oil to methanol ratio of 1 : 9 and stirred for 1 hour, using different TiO2/g-C3N4 catalysts (10, 20 & 30%) with different catalyst concentrations of 1%, 2% and 3%. The results showed that TiO2/20% g-C3N4 with 2% catalyst concentration gives the highest yield of biodiesel production (89.5%) as compared to other catalyst concentrations used. In addition to (FTIR), additional fuel characteristics such as density, viscosity, flashpoint, acid value, and pH were tested to determine the quality of the generated biodiesel and were found to comply with fuel standards. With high stability and good catalytic activity, the synthesized composite TiO2/g-C3N4 is a viable option for producing biodiesel from WCO.
| S-EPMC9043783 | biostudies-literature
Project description:A waste snail shell (Pila spp.) derived catalyst was used to produce biodiesel from soybean oil at room temperature for the first time. The snail shell was calcined at different temperatures of 400-1000 °C. The synthesized catalysts underwent XRD, SEM, TEM, EDS, FTIR, XRF, TG/DTA and N2 adsorption-desorption isotherm (BET) analysis. The major component CaO was determined at a calcination temperature of 900 °C as depicted in the XRD results. 100% conversion of soybean oil to methyl ester biodiesel was obtained, as confirmed by 1H NMR. A biodiesel yield of 98% was achieved under optimized reaction conditions such as a calcination temperature of 900 °C, a catalyst loading of 3 wt%, a reaction time of 7 h and a methanol to oil ratio of 6 : 1, and biodiesel conversion was confirmed by FT-NMR and IR spectroscopies. A total of 9 fatty acid methyl esters (FAMEs) were identified in the synthesized biodiesel by the retention time and fragmentation pattern data of GC-MS analysis. The catalyst was recycled 8 times without appreciable loss in its catalytic activity. A high biodiesel yield of 98% was obtained under these optimised conditions. The catalyst has the advantage of being a waste material, therefore it is easily prepared, cost free, highly efficient, biogenic, labor effective and environmentally friendly, making it a potential candidate as a green catalyst for low cost production of biodiesel at an industrial scale.
| S-EPMC9080767 | biostudies-literature
Project description:Sulfonation of graphitic carbon nitride (g-CN) affords a polar and strongly acidic catalyst, Sg-CN, which displays unprecedented reactivity and selectivity in biodiesel synthesis and esterification reactions at room temperature.
| S-EPMC5172360 | biostudies-literature
Project description:In this study, biodiesel production from microalgal oil by microwave-assisted transesterification was carried out to investigate its efficiency. Transesterification reactions were performed by using Chlorella protothecoides oil as feedstock, methanol, and potassium hydroxide as the catalyst. Methanol:oil ratio, reaction time and catalyst:oil ratio were investigated as process parameters affected methyl ester yield. 9:1 methanol/oil molar ratio, 1.5% KOH catalyst/oil ratio and 10 min were optimum values for the highest fatty acid methyl ester yield.
| S-EPMC4849035 | biostudies-literature
Project description:A catalyst from the pharmaceutical waste of calcium and magnesium tablets was synthesized for biodiesel production from waste Pistacia-Terebinthus (PT) oil with the aim of creating added value and presenting a new approach for the management of such wastes. For this purpose, magnesium and calcium tablet wastes with a mass ratio of 70:30 (wt%) were calcined. The catalyst was investigated by several methods, such as thermal gravimetric analysis, X-ray diffraction, Fourier transform infrared spectroscopy, field emission scanning electron microscopy, Brunauer-Emmett-Teller analysis, X-ray photoelectron spectroscopy, and CHNS/O elemental analysis. The high specific surface area of the catalyst confirms that the utilized synthesis method resulted in the formation of a high number of active sites in its structure, which allows it to function as a suitable catalyst for this reaction. Furthermore, the impact of effective parameters on the treansestrification reaction was optimized and investigated by designing the experiments and applying the RSM method. The maximum mass yield of 96 % was obtained in optimal conditions (temperature of 70 °C, catalyst loading of 4.498 wt%, methanol:oil ratio of 1.968 (vol:vol), and reaction time of 120 min). The reusability of the catalyst was investigated in four successive cycles. The mass yield of the last test declined from 96 % to 71.4 %. Gas chromatography-mass spectrometry analysis of the produced biofuel revealed that it comprises 91.37 % methyl ester compounds (64.28 % 12-Octadecenoic Acid, Methyl Ester). To evaluate the external costs of biofuel (B100) and compare it with diesel, combustion simulation was done with Diesel-RK software, which showed that its external costs were 0.05388 (€/Lit fuel) less than those of diesel.
| S-EPMC11325280 | biostudies-literature
Project description:The present study focuses on the catalytic activity of cesium modified natural phosphate in biodiesel production from rapeseed oil and low free fatty acids (FFA) used in cooking oil. The catalyst was prepared by impregnation of cesium chloride (CsCl) on the natural phosphate followed by calcination up to 800 °C. The phosphate based catalyst was thermally, structurally, morphologically, and texturally characterized in order to determinate the relationship between its physicochemical properties and its catalytic activity. The chosen catalyst was demonstrated to be an active catalyst for the transesterification of rapeseed oil achieving a biodiesel yield of 99.55% under suitable reaction conditions: a methanol to oil molar ratio of 12 : 1, reaction temperature of 70 °C, catalyst amount of 4 wt% based on oil weight and reaction time of 6 h. Results from low FFA waste cooking oil transesterification indicated that a methyl esters yield of 99.52% could be obtained. Furthermore, results from esterification/transesterification of acidified rapeseed oil indicate that a yield of 93% may be obtained, thus giving rise to a potential application in 2nd generation biodiesel production from low acidic oils. Some important physicochemical properties of the obtained biodiesel were evaluated and compared with the EN14214 and ASTM D-6751 standards for biodiesel specifications.
| S-EPMC9057709 | biostudies-literature
Project description:Graphitic carbon nitride (gCN) is a promising organic platform for driving light-activated charge-transfer reactions in a number of valuable photocatalytic cycles. A primary limitation of gCN as a photocatalyst is its short excited-state lifetime, which is mediated by a high density of trap and defect sites that result in rapid excited-state decay and low photocatalytic efficiency. To enhance the catalytic activity, gCN is often functionalized with a metal co-catalyst; however, the mechanism by which metal co-catalysts enhance the reactivity has not been clearly established. In this work, the excited-state dynamics of gCN and silver-modified gCN are compared using ultrafast transient absorption and time-resolved photoluminescence spectroscopies. In silver-modified gCN, an ultrafast spectral shift in the silver plasmon resonance provides direct spectral evidence of electron transfer from gCN to the silver nanoparticles. The electron-transfer rate is competitive with other non-radiative relaxation pathways, with electron-transfer yields approaching 50%, thus providing an effective strategy for mitigating losses associated with defects and trap sites.
| S-EPMC10064998 | biostudies-literature
Project description:Biodiesel, a mixture of fatty acid methyl esters (FAME), is bio-renewable, non-toxic, biodegradable, and is an attractive alternative to petroleum diesel. This work studied the sonochemical transesterification of Lesquerella fendleri oil (LFO) using inexpensive solid Lewis acid (LA) catalysts with an aim to reduce environmental pollution and dependance on non-renewable fuel sources. Due to the presence of hydroxy fatty acid methyl esters (HFAME) in LFO (∼60%), in addition to producing biofuel it can also be used to generate chemically important estolides and cyclic lactones. AlCl3, SnCl2, and Sn(CH3COO)2 showed catalytic activity using direct immersion ultrasound (DI-US) among a list of LA catalysts investigated, with AlCl3 being the best catalyst. Ultrasound increased the reaction rate by facilitating carbocation formation of glyceridic carbons. Experiments were carried out at room temperature in a solvent range from 3:1 to 18:1 methanol-to-oil molar ratio and catalyst loading from 1 wt% to 6 wt% over 10 to 60 min sonication time at 48% ultrasound amplitude (roughly 17 W/cm2). Complete conversion (>99%) was achieved in 40 min with 5 wt% AlCl3 catalyst. A statistical regression analysis with STATA 14.0 software was performed to optimize process parameters. Chemical characterizations of the compounds were performed with nuclear magnetic resonance (NMR) spectroscopy (1H NMR & 13C NMR), and % conversion of FAMEs was calculated from the 1H NMR spectra. The fatty acid profile was determined by GC-FID and GC-MS analysis. FT-IR spectroscopic analysis and thermogravimetric analysis (TGA) were performed to investigate the infrared absorption pattern of the compound and the volatility difference between Lesquerella fendleri biodiesel and oil under nitrogen atmosphere. Results indicate that this is a fast, green, energy-efficient, sustainable, and industrially applicable method for biodiesel production from LFO.
| S-EPMC9256648 | biostudies-literature
Project description:Key challenges for the application of biodiesel include their high acid value, high viscosity, and low ester content. It is essential to develop later-generation biodiesel from unexploited non-food resources for a more sustainable future. Reuse of biowaste is critically important to address these issues of food safety and sustainability. Thus, the co-transesterification of waste cooking oil (WCO), algal oil (AO) and dimethyl carbonate (DMC) for the synthesis of fatty acid methyl esters (FAMEs) was investigated over a series of nanoparticle catalysts containing calcium, magnesium, potassium or nickel under mild reaction conditions. Nanoparticle catalyst samples were prepared from biowaste sources of chicken manure (CM), water hyacinth (WH) and algal bloom (AB), and characterized using XRD, Raman and FESEM techniques for the heterogeneous production of biodiesel. The catalyst was initially prepared by calcination at 850 °C for 4 h in a major presence of CaxMgyCO3, KCl and K2CO3. The WCO and AO co-conversion of 98% and FAMEs co-selectivity of 95% were obtained over CM nanoparticle catalyst under the reaction conditions of 80 °C, 20 mins and DMC to oil molar ratio of 6:1 with 3% catalyst loading and 3% methanol addition. Under the optimum condition, the density, viscosity, and cetane number of the biodiesel were in the range of diesel standards. Nanoparticle catalysts have been proven as a promising sustainable material in the catalytic transesterification of WCO and AO with the major presence of calcium, magnesium and potassium. This study highlights a sustainable approach via biowaste utilization for the enhancement of biodiesel quality with high ester content, low acid value, high cetane number, and low viscosity.
| S-EPMC7494454 | biostudies-literature
Project description:A number of samples from solid food waste oil (SFWO) from different restaurants have been collected. Data regarding fatty acid profile, acid value, water content and kinematic viscosity were used for characterization purposes. Response surface methodology data has been used to carry out conventional transesterification optimization. The quality of the final product has been checked following the European biodiesel standard EN14214. To compare conventional and ultrasound-assisted transesterification results, energy consumption and reaction time data have been gathered. More information and result interpretation may be found in "Optimization of solid food waste oil biodiesel by ultrasound assisted transesterification" [1].
| S-EPMC7154990 | biostudies-literature