Performance benchmarks for open source porous electrode theory models.
Ontology highlight
ABSTRACT:
SUBMITTER: Ayalasomayajula SM
PROVIDER: S-EPMC11004710 | biostudies-literature | 2024 Apr
REPOSITORIES: biostudies-literature
Publications
Performance benchmarks for open source porous electrode theory models.
Ayalasomayajula Surya Mitra SM Cogswell Daniel D Zhuang Debbie D García R Edwin RE
Heliyon 20240320 7
The electrochemical response characteristics of existing and emerging porous electrode theory (PET) models was benchmarked to establish a common basis to assess their physical reaches, limitations, and accuracy. Three open source PET models: dualfoil, MPET, and LIONSIMBA were compared to simulate the discharge of a LiMn<sub>2</sub>O<sub>4</sub>-graphite cell against experimental data. For C-rates below 2C, the simulated discharge voltage curves matched the experimental data within 4% deviation f ...[more]
Similar Datasets
Project description:All-solid-state batteries (ASSBs) have become an important technology because of their high performance and low-risk operation. However, the high interface resistance and low ionic conductivity of ASSBs hinder their application. In this study, a self-developed electrochemical model based on an open-source computational fluid dynamics platform is presented. The effect of contact area reduction at the electrode/solid-state electrolyte interface is investigated. Then, a new conceptual 3D structure is introduced to circumvent the existing barriers. The results demonstrate that the discharge time is shortened by over 20% when the area contact ratio reduces from 1.0 to 0.8 at 1 C-rate, owing to the increased overpotential. By adopting the new 3D pillar design, the energy density of ASSBs can be improved. However, it is only when a 3D current collector is contained in the cathode that the battery energy/power density, capacity, and material utilization can be greatly enhanced without being limited by pillar height issues. Therefore, this work provides important insight into the enhanced performance of 3D structures.
| S-EPMC9069203 | biostudies-literature
Project description:Deep brain stimulation (DBS) is an effective surgical treatment for movement disorders. Although stimulation sites for movement disorders such as Parkinson's disease are established, the therapeutic mechanisms of DBS remain controversial. Recent research suggests that specific white-matter tract and circuit activation mediates symptom relief. To investigate these questions, we have developed a patient-specific open-source software pipeline called 'DBSproc' for (1) localizing DBS electrodes and contacts from postoperative CT images, (2) processing structural and diffusion MRI data, (3) registering all images to a common space, (4) estimating DBS activation volume from patient-specific voltage and impedance, and (5) understanding the DBS contact-brain connectivity through probabilistic tractography. In this paper, we explain our methodology and provide validation with anatomical and tractographic data. This method can be used to help investigate mechanisms of action of DBS, inform surgical and clinical assessments, and define new therapeutic targets.
| S-EPMC5217472 | biostudies-literature
Project description:Management of solid oxide fuel cell (SOFC) thermal gradients is vital to limit thermal expansion mismatch and thermal stress. However, owing to harsh operation conditions of SOFCs and limited available space in stack configuration, the number of techniques available to obtain temperature distribution from the cell surface is limited. The authors previously developed and studied a thermocouple array pattern to detect surface temperature distribution on an SOFC in open circuit conditions. In this study, the performance in terms of mechanical durability and oxidation state of the thin film thermoelements of the thermocouple array on the porous SOFC cathode is investigated. A thin-film multi-junction thermocouple array was sputter deposited using a magnetron sputter coater. Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) characterisation techniques were carried out to understand characteristics of the thin film before and after temperature (20 °C-800 °C) measurement. Temperature readings from the sensor agreed well with the closely placed commercial thermocouple during heating segments. However, a sensor failure occurred at around 350 °C during the cooling segment. The SEM and XPS tests revealed cracks on the thin film thermoelements and oxidation to the film thickness direction.
| S-EPMC5038619 | biostudies-literature
Project description:Bayesian models constructed from structure-derived fingerprints have been a popular and useful method for drug discovery research when applied to bioactivity measurements that can be effectively classified as active or inactive. The results can be used to rank candidate structures according to their probability of activity, and this ranking benefits from the high degree of interpretability when structure-based fingerprints are used, making the results chemically intuitive. Besides selecting an activity threshold, building a Bayesian model is fast and requires few or no parameters or user intervention. The method also does not suffer from such acute overtraining problems as quantitative structure-activity relationships or quantitative structure-property relationships (QSAR/QSPR). This makes it an approach highly suitable for automated workflows that are independent of user expertise or prior knowledge of the training data. We now describe a new method for creating a composite group of Bayesian models to extend the method to work with multiple states, rather than just binary. Incoming activities are divided into bins, each covering a mutually exclusive range of activities. For each of these bins, a Bayesian model is created to model whether or not the compound belongs in the bin. Analyzing putative molecules using the composite model involves making a prediction for each bin and examining the relative likelihood for each assignment, for example, highest value wins. The method has been evaluated on a collection of hundreds of data sets extracted from ChEMBL v20 and validated data sets for ADME/Tox and bioactivity.
| S-EPMC4764945 | biostudies-other
Project description:The localization of intracranial electrodes is a fundamental step in the analysis of invasive electroencephalography (EEG) recordings in research and clinical practice. The conclusions reached from the analysis of these recordings rely on the accuracy of electrode localization in relationship to brain anatomy. However, currently available techniques for localizing electrodes from magnetic resonance (MR) and/or computerized tomography (CT) images are time consuming and/or limited to particular electrode types or shapes. Here we present iElectrodes, an open-source toolbox that provides robust and accurate semi-automatic localization of both subdural grids and depth electrodes. Using pre- and post-implantation images, the method takes 2-3 min to localize the coordinates in each electrode array and automatically number the electrodes. The proposed pre-processing pipeline allows one to work in a normalized space and to automatically obtain anatomical labels of the localized electrodes without neuroimaging experts. We validated the method with data from 22 patients implanted with a total of 1,242 electrodes. We show that localization distances were within 0.56 mm of those achieved by experienced manual evaluators. iElectrodes provided additional advantages in terms of robustness (even with severe perioperative cerebral distortions), speed (less than half the operator time compared to expert manual localization), simplicity, utility across multiple electrode types (surface and depth electrodes) and all brain regions.
| S-EPMC5333374 | biostudies-literature
Project description:Nanoporous polymers are becoming increasingly interesting materials for electrochemical applications, as their large surface areas with redox-active sites allow efficient adsorption and diffusion of ions. However, their limited electrical conductivity remains a major obstacle in practical applications. The conventional approach that alleviates this problem is the hybridisation of the polymer with carbon-based additives, but this directly prevents the utilisation of the maximum capacity of the polymers. Here, we report a layer-by-layer fabrication technique where we separated the active (porous polymer, top) layer and the conductive (carbon, bottom) layer and used these "layered" electrodes in a supercapacitor (SC). Through this approach, direct contact with the electrolyte and polymer material is greatly enhanced. With extensive electrochemical characterisation techniques, we show that the layered electrodes allowed a significant contribution of fast faradic surface reactions to the overall capacitance. The electrochemical performance of the layered-electrode SC outperformed other reported porous polymer-based devices with a specific gravimetric capacitance of 388 F·g-1 and an outstanding energy density of 65 Wh·kg-1 at a current density of 0.4 A·g-1. The device also showed outstanding cyclability with 90% of capacitance retention after 5000 cycles at 1.6 A·g-1, comparable to the reported porous polymer-based SCs. Thus, the introduction of a layered electrode structure would pave the way for more effective utilisation of porous organic polymers in future energy storage/harvesting and sensing devices by exploiting their nanoporous architecture and limiting the negative effects of the carbon/binder matrix.
| S-EPMC8745899 | biostudies-literature
Project description:Acquiring accurate 3D biological models efficiently and economically is important for morphological data collection and analysis in organismal biology. In recent years, structure-from-motion (SFM) photogrammetry has become increasingly popular in biological research due to its flexibility and being relatively low cost. SFM photogrammetry registers 2D images for reconstructing camera positions as the basis for 3D modeling and texturing. However, most studies of organismal biology still relied on commercial software to reconstruct the 3D model from photographs, which impeded the adoption of this workflow in our field due the blocking issues such as cost and affordability. Also, prior investigations in photogrammetry did not sufficiently assess the geometric accuracy of the models reconstructed. Consequently, this study has two goals. First, we presented an affordable and highly flexible SFM photogrammetry pipeline based on the open-source package OpenDroneMap (ODM) and its user interface WebODM. Second, we assessed the geometric accuracy of the photogrammetric models acquired from the ODM pipeline by comparing them to the models acquired via microCT scanning, the de facto method to image skeleton. Our sample comprised 15 Aplodontia rufa (mountain beaver) skulls. Using models derived from microCT scans of the samples as reference, our results showed that the geometry of the models derived from ODM was sufficiently accurate for gross metric and morphometric analysis as the measurement errors are usually around or below 2%, and morphometric analysis captured consistent patterns of shape variations in both modalities. However, subtle but distinct differences between the photogrammetric and microCT-derived 3D models could affect the landmark placement, which in return affected the downstream shape analysis, especially when the variance within a sample is relatively small. At the minimum, we strongly advise not combining 3D models derived from these two modalities for geometric morphometric analysis. Our findings can be indictive of similar issues in other SFM photogrammetry tools since the underlying pipelines are similar. We recommend that users run a pilot test of geometric accuracy before using photogrammetric models for morphometric analysis. For the research community, we provide detailed guidance on using our pipeline for building 3D models from photographs.
| S-EPMC10350669 | biostudies-literature
Project description:The application of 3D printing to biological research has provided the tissue engineering community with a method for organizing cells and biological materials into complex 3D structures. While many commercial bioprinting platforms exist, they are expensive, ranging from $5000 to over $1,000,000. This high cost of entry prevents many labs from incorporating 3D bioprinting into their research. Due to the open-source nature of desktop plastic 3D printers, an alternative option has been to convert low-cost plastic printers into bioprinters. Several open-source modifications have been described, but there remains a need for a user-friendly, step-by-step guide for converting a thermoplastic printer into a bioprinter using components with validated performance. Here we convert a low-cost 3D printer, the FlashForge Finder, into a bioprinter using our Replistruder 4 syringe pump and the Duet3D Duet 2 WiFi for total cost of less than $900. We demonstrate that the accuracy of the bioprinter's travel is better than 35 µm in all three axes and quantify fidelity by printing square lattice collagen scaffolds with average errors less than 2%. We also show high fidelity reproduction of clinical-imaging data by printing a scaffold of a human ear using collagen bioink. Finally, to maximize accessibility and customizability, all components we have designed for the bioprinter conversion are provided as open-source 3D models, along with instructions for further modifying the bioprinter for additional use cases, resulting in a comprehensive guide for the bioprinting field.
| S-EPMC9805454 | biostudies-literature
Project description:Interpretation of QSAR models is useful to understand the complex nature of biological or physicochemical processes, guide structural optimization or perform knowledge-based validation of QSAR models. Highly predictive models are usually complex and their interpretation is non-trivial. This is particularly true for modern neural networks. Various approaches to interpretation of these models exist. However, it is difficult to evaluate and compare performance and applicability of these ever-emerging methods. Herein, we developed several benchmark data sets with end-points determined by pre-defined patterns. These data sets are purposed for evaluation of the ability of interpretation approaches to retrieve these patterns. They represent tasks with different complexity levels: from simple atom-based additive properties to pharmacophore hypothesis. We proposed several quantitative metrics of interpretation performance. Applicability of benchmarks and metrics was demonstrated on a set of conventional models and end-to-end graph convolutional neural networks, interpreted by the previously suggested universal ML-agnostic approach for structural interpretation. We anticipate these benchmarks to be useful in evaluation of new interpretation approaches and investigation of decision making of complex "black box" models.
| S-EPMC8157407 | biostudies-literature
Project description:Functional assessment of in vitro neuronal networks-of relevance for disease modelling and drug testing-can be performed using multi-electrode array (MEA) technology. However, the handling and processing of the large amount of data typically generated in MEA experiments remains a huge hurdle for researchers. Various software packages have been developed to tackle this issue, but to date, most are either not accessible through the links provided by the authors or only tackle parts of the analysis. Here, we present ''MEA-ToolBox'', a free open-source general MEA analytical toolbox that uses a variety of literature-based algorithms to process the data, detect spikes from raw recordings, and extract information at both the single-channel and array-wide network level. MEA-ToolBox extracts information about spike trains, burst-related analysis and connectivity metrics without the need of manual intervention. MEA-ToolBox is tailored for comparing different sets of measurements and will analyze data from multiple recorded files placed in the same folder sequentially, thus considerably streamlining the analysis pipeline. MEA-ToolBox is available with a graphic user interface (GUI) thus eliminating the need for any coding expertise while offering functionality to inspect, explore and post-process the data. As proof-of-concept, MEA-ToolBox was tested on earlier-published MEA recordings from neuronal networks derived from human induced pluripotent stem cells (hiPSCs) obtained from healthy subjects and patients with neurodevelopmental disorders. Neuronal networks derived from patient's hiPSCs showed a clear phenotype compared to those from healthy subjects, demonstrating that the toolbox could extract useful parameters and assess differences between normal and diseased profiles.
| S-EPMC9588481 | biostudies-literature