Agglutination of single catalyst particles during fluid catalytic cracking as observed by X-ray nanotomography.
Ontology highlight
ABSTRACT:
SUBMITTER: Meirer F
PROVIDER: S-EPMC4424819 | biostudies-literature | 2015 May
REPOSITORIES: biostudies-literature
Publications
Agglutination of single catalyst particles during fluid catalytic cracking as observed by X-ray nanotomography.
Meirer F F Kalirai S S Nelson Weker J J Liu Y Y Andrews J C JC Weckhuysen B M BM
Chemical communications (Cambridge, England) 20150414 38
Metal accumulation at the catalyst particle surface plays a role in particle agglutination during fluid catalytic cracking. ...[more]
Similar Datasets
Project description:Microprobe X-ray fluorescence tomography was used to investigate metal poison deposition in individual, intact and industrially deactivated fluid catalytic cracking (FCC) particles at two differing catalytic life-stages. 3 D multi-element imaging, at submicron resolution was achieved by using a large-array Maia fluorescence detector. Our results show that Fe, Ni and Ca have significant concentration at the exterior of the FCC catalyst particle and are highly co-localized. As concentrations increase as a function of catalytic life-stage, the deposition profiles of Fe, Ni, and Ca do not change significantly. V has been shown to penetrate deeper into the particle with increasing catalytic age. Although it has been previously suggested that V is responsible for damaging the zeolite components of FCC particles, no spatial correlation was found for V and La, which was used as a marker for the embedded zeolite domains. This suggests that although V is known to be detrimental to zeolites in FCC particles, a preferential interaction does not exist between the two.
| S-EPMC4648052 | biostudies-literature
Project description:Fluid catalytic cracking (FCC) is a major process in oil refineries to produce gasoline and base chemicals from crude oil fractions. The spatial distribution and acidity of zeolite aggregates embedded within the 50-150 μm-sized FCC spheres heavily influence their catalytic performance. Single-molecule fluorescence-based imaging methods, namely nanometer accuracy by stochastic chemical reactions (NASCA) and super-resolution optical fluctuation imaging (SOFI) were used to study the catalytic activity of sub-micrometer zeolite ZSM-5 domains within real-life FCC catalyst particles. The formation of fluorescent product molecules taking place at Brønsted acid sites was monitored with single turnover sensitivity and high spatiotemporal resolution, providing detailed insight in dispersion and catalytic activity of zeolite ZSM-5 aggregates. The results point towards substantial differences in turnover frequencies between the zeolite aggregates, revealing significant intraparticle heterogeneities in Brønsted reactivity.
| S-EPMC4506548 | biostudies-literature
Project description:Bioleaching uses biodegradable organic acids, thereby making the process environmental friendly as compared to chemical leaching. In this work, bioleaching of aluminium (Al) metal from spent catalyst was investigated by using three Aspergillus strains (A. niger, A. foetidus, and A. carbonarius). Bioleaching was performed in batch culture mode at different loading densities of spent catalyst (i.e., 0.4%, 0.8% and 1.2% (w/v)). The highest Al leaching efficiency of 88.43% was obtained at 0.8% ((w/v)) catalyst loading using A. foetidus, further increase in the catalyst loading decreased the efficiency. In addition to this, molasses was used as a carbon source (low-cost) at various concentrations for bioleaching of spent catalyst and the results were found to be significant at 40 g/L sugar concertation with 60% bioleaching efficiency. Overall, this study indicates that A. foetidus have the potential for leaching of Al from spent catalysts. Therefore, present research findings suggested that, instead of using mineral acids, organic acids (biodegradable) usage for metal leaching process is highly reliable and eco-friendly as well.
| S-EPMC6551381 | biostudies-literature
Project description:Ziegler-type catalysts are the grand old workhorse of the polyolefin industry, yet their hierarchically complex nature complicates polymerization activity-catalyst structure relationships. In this work, the degree of catalyst framework fragmentation of a high-density polyethylene (HDPE) Ziegler-type catalyst was studied using ptychography X-ray-computed nanotomography (PXCT) in the early stages of ethylene polymerization under mild reaction conditions. An ensemble consisting of 434 fully reconstructed ethylene prepolymerized Ziegler catalyst particles prepared at a polymer yield of 3.4 g HDPE/g catalyst was imaged. This enabled a statistical route to study the heterogeneity in the degree of particle fragmentation and therefore local polymerization activity at an achieved 3-D spatial resolution of 74 nm without requiring invasive imaging tools. To study the degree of catalyst fragmentation within the ensemble, a fragmentation parameter was constructed based on a k-means clustering algorithm that relates the quantity of polyethylene formed to the average size of the spatially resolved catalyst fragments. With this classification method, we have identified particles that exhibit weak, moderate, and strong degrees of catalyst fragmentation, showing that there is a strong heterogeneity in the overall catalyst particle fragmentation and thus polymerization activity within the entire ensemble. This hints toward local mass transfer limitations or other deactivation phenomena. The methodology used here can be applied to all polyolefin catalysts, including metallocene and the Phillips catalysts to gain statistically relevant fundamental insights in the fragmentation behavior of an ensemble of catalyst particles.
| S-EPMC8243319 | biostudies-literature
Project description:Fluid catalytic cracking (FCC) is an important process in oil refinery industry to produce gasoline and propylene. Due to harsh reaction conditions, FCC catalysts are subject to deactivation through for example, metal accumulation and zeolite framework collapse. Here, we perform a screening of the influence of metal poisons on the acidity and accessibility of an industrial FCC catalyst material using laboratory-based single particle characterization that is, μ-XRF and fluorescence microscopy in combination with probe molecules. These methods have been performed on density-separated FCC catalyst fractions, allowing to determine interparticle heterogeneities in the catalyst under study. It was found that with increasing catalyst density and metal content, the acidity and accessibility of the catalyst particles decreased, while their distribution narrowed with catalyst age. For example, particles containing high Ni level possessed very low acidity and were hardly accessible by a Nile Blue dye. Single catalyst particle mapping identifies minority species like the presence of a phosphated zeolite ZSM-5-containing FCC additive for selective propylene formation, catalyst particles without any zeolite phase and catalyst particles, which act as a trap for SOx .
| S-EPMC7384009 | biostudies-literature
Project description:Full-field transmission X-ray microscopy has been used to determine the 3D structure of a whole individual fluid catalytic cracking (FCC) particle at high spatial resolution and in a fast, noninvasive manner, maintaining the full integrity of the particle. Using X-ray absorption mosaic imaging to combine multiple fields of view, computed tomography was performed to visualize the macropore structure of the catalyst and its availability for mass transport. We mapped the relative spatial distributions of Ni and Fe using multiple-energy tomography at the respective X-ray absorption K-edges and correlated these distributions with porosity and permeability of an equilibrated catalyst (E-cat) particle. Both metals were found to accumulate in outer layers of the particle, effectively decreasing porosity by clogging of pores and eventually restricting access into the FCC particle.
| S-EPMC4435782 | biostudies-literature
Project description:Matrix effects in a fluid catalytic cracking (FCC) catalyst have been studied in terms of structure, accessibility, and acidity. An extensive characterization study into the structural and acidic properties of a FCC catalyst, its individual components (i.e., zeolite H-Y, binder (boehmite/silica) and kaolin clay), and two model FCC catalyst samples containing only two components (i.e., zeolite-binder and binder-clay) was performed at relevant conditions. This allowed the drawing of conclusions about the role of each individual component, describing their mutual physicochemical interactions, establishing structure-acidity relationships, and determining matrix effects in FCC catalyst materials. This has been made possible by using a wide variety of characterization techniques, including temperature-programmed desorption of ammonia, infrared spectroscopy in combination with CO as probe molecule, transmission electron microscopy, X-ray diffraction, Ar physisorption, and advanced nuclear magnetic resonance. By doing so it was, for example, revealed that a freshly prepared spray-dried FCC catalyst appears as a physical mixture of its individual components, but under typical riser reactor conditions, the interaction between zeolite H-Y and binder material is significant and mobile aluminum migrates and inserts from the binder into the defects of the zeolite framework, thereby creating additional Brønsted acid sites and restoring the framework structure.
| S-EPMC7539955 | biostudies-literature
Project description:Refiners around the globe are either considering or are actively replacing a portion of their crude oil inputs originating from fossil sources with alternative sources, including recycled materials (plastics, urban waste, mixed solid waste) and renewable materials (bio-mass waste, vegetable oils). In this paper, we explore such replacement, specifically focusing on the fluid catalytic cracking (FCC) operation. Five pyrolysis oils, obtained from municipal solid waste (MSW) and biogenic material (olive stones/pits), were fully characterized and tested at 10% loading against a standard fluid catalytic cracking (FCC) vacuum gasoil (VGO) feed in a bench scale reactor using an industrially available fluid catalytic cracking catalyst based on ultrastable Y zeolite to simulate fluid catalytic cracking co-processing. Despite having unique feed properties, including high Conradson carbon (e.g., up to 19.41 wt%), water (e.g., up to 5.7 wt%), and contaminants (e.g., up to 227 ppm Cl) in some cases, the five pyrolysis oils gave similar yield patterns as vacuum gasoil. Gasoline was slightly (ca. 1 wt%) higher in all cases and LPG slightly (ca. 1 wt%) lower. Olefinicity in the LPG streams were unchanged, bottoms and light cycle oil (LCO) showed no significant changes, while dry gas was slightly (up to -0.2 wt%) lower. Coke selectivity was also unchanged (maximum -7.7 wt%, relatively), suggesting minimal to no heat balance concerns when co-processing in an industrial fluid catalytic cracking unit. The results demonstrate the applicability of municipal solid waste and biogenic originating pyrolysis oils into a refinery. A catalyst design concept is explored, based on higher rare Earth oxide exchange and/or utilization of ZSM-5 zeolite, that would further minimize the impacts of replacing fossil oils with pyrolysis oils, namely one that shifts the 1% higher gasoline into LPG.
| S-EPMC9893771 | biostudies-literature
Project description:This work provided catalytic copyrolysis of spent lubricating oil (SLO) with waste low-density polyethylene (LDPE) using copper modification of a spent fluid catalytic cracking (sFCC) catalyst to produce diesel-like fuels in a microbatch reactor, which will lead to effective waste management, ensure sustainability, and serve as an alternative energy source. The effects of LDPE blended with SLO, temperature, reaction time, and catalyst loading using an inert nitrogen atmosphere were investigated on the yields and distributions of copyrolyzed oil, while metal modification of the sFCC was prepared and used to investigate the catalytic activity. The temperature and time of reaction played an important role in the gaseous contribution to the pyrolysis of SLO. The addition of the LDPE ratio in the catalytic copyrolysis, including Cu loading on a spent FCC template, also enhanced the acidity and was responsible for the catalytic activity, which could improve the product distribution and chemical compounds in a range of diesel-like fuels. It was shown that the pyrolyzed oil was in the range of C7-C26 with a maximum diesel-like fraction of 23.11 ± 2.88 wt % compared with the catalytic pyrolysis of SLO alone, which contained a diesel-like fraction of only 12.45 ± 1.92 wt %. It was noticed that the acid active site of the catalyst resulted in a carbon-carbon bond cleavage and further secondary reaction, leading to the conversion of the long residue fraction into a light oil product. In addition, the LDPE ratio in the catalytic copyrolysis could improve the product distribution and chemical compounds in a range of diesel-like compounds, as confirmed by the GC/MS analysis. Catalytic copyrolysis oil of the optimal process condition (0.7:0.3 mass molar of SLO/LDPE, 450 °C, 60 min, 3 wt % Cu-sFCC, and 10 wt % catalyst loading) mainly contains light hydrocarbons in the C7-C19 range. Accordingly, both the product selectivity and the conversion of the long residue to the diesel-like fraction were nearly stable (59.01 ± 1.36%) during the catalyst reusability test from one to three cycles without regeneration and significantly decreased after the fifth cycle. This is an indication that the copyrolysis enhanced the conversion of SLO by LPDE blended into smaller hydrocarbon compounds, and the catalytic activity therefore showed a major tendency toward the formation of diesel-like fractions (C8-C18).
| S-EPMC10620889 | biostudies-literature
Project description:Catalytic pyrolysis of polymer waste is an attractive alternative process for the conversion of large hydrocarbon compounds to useful products for the most reliable fueling and valuable chemicals, growing toward a circular economy and enhancing the reduction of waste materials. In this study, catalytic pyrolysis of waste polyethylene wax (WPEW) using a dual acid-acid catalyst and acid-base catalyst, which had various pore size distributions and included a strong active site, maximized the desirable yield and product distribution. The effect of the process conditions and synergy of activated carbon (AC) blended into both a spent fluid catalytic cracking catalyst (FCC) and magnesium oxide (MgO) catalyst was examined in a 3000 cm3 custom-built reactor at varying operating temperatures (400-470 °C), inert nitrogen gas flow rates (50 mL min-1), catalyst loading (1-5 wt %), and FCC-AC and MgO-AC ratios in the catalytic conversion of WPEW to obtain the highest amount of diesel-like oil. The results indicated that thermal cracking of WPEW at 420 °C by a fixed inert N2 flow rate of 50 mL min-1 obtained the highest liquid yield of 81.64 wt % and a diesel-like fraction of 35.51 wt %, while the catalytic conversion of WPEW under optimum conditions (temperature: 420 °C; fixed inert N2 flow rate: 50 mL min-1; catalyst load: 5 wt %; MgO-AC ratio: 0.5:0.5) achieved the highest liquid diesel-like yield of 41.92 wt %. Physicochemical analyses showed that the highest heating value of WPEW pyrolytic oil was 44.20 MJ kg-1, and the viscosity was 1.7 mm2 s-1 at 40 °C. The combination of MgO-AC as a dual catalyst illustrates a positive synergistic effect on the catalytic activity performance markedly, outstanding catalytic characteristics alongside high selectivity in pyrolysis of WPEW to paraffinic hydrocarbons in the diesel-like fraction.
| S-EPMC9202014 | biostudies-literature