Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Distance effects in electrochemical micromachining.

ABSTRACT: Considering exponential dependence of currents on double-layer voltage and the feedback effect of the electrolyte resistance, a distance effect in electrochemical micromachining is found, namely that both time constant and double-layer voltage depend on the separation of electrodes. The double-layer voltage is the real voltage used in processing. Under DC voltage, the apparent voltages between two electrodes are constant for different separations, but the real voltages change with the separations. Small separations exert substantial effects on the real voltages. Accordingly, a DC-voltage small-separation electrochemical micromachining technique was proposed. The double-layer voltage drops sharply as the small separation increases. Thus, the electrochemical reactions are confined to electrode regions in very close proximity even under DC voltage. The machining precision can be significantly enhanced by reducing the voltage and separation between electrodes. With this technique, the machining of conducting materials with submicrometre precision was achieved.

SUBMITTER: Xu L

PROVIDER: S-EPMC5007593 | biostudies-literature | 2016 Sep

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Publications

Distance effects in electrochemical micromachining.

Xu Lizhong L Pan Yue Y Zhao Chuanjun C

Scientific reports 20160901

Considering exponential dependence of currents on double-layer voltage and the feedback effect of the electrolyte resistance, a distance effect in electrochemical micromachining is found, namely that both time constant and double-layer voltage depend on the separation of electrodes. The double-layer voltage is the real voltage used in processing. Under DC voltage, the apparent voltages between two electrodes are constant for different separations, but the real voltages change with the separation ...[more]

PMID: 27581708

Similar Datasets

Development of nanosecond spike pulse power supply for electrochemical micromachining.

Project description:The use of pulse voltage can greatly improve the precision of electrochemical microfabrication, and the narrower the pulse width of the applied pulse voltage signal, the higher the machining precision. However, the commonly used chopper circuit topology of pulse power supplies is limited by the maximum switching frequency of the field-effect transistor. To address this problem, this paper proposes a nanosecond pulse electrochemical micromachining power supply based on a differential circuit. The power supply uses the STM32F103C8T6 microcontroller as the control core to output high-performance rectangular waves through a DDS device. After differential, rectification, filtering, and power amplification processing, stable, frequency, amplitude, and pulse width adjustable spike pulse voltage signals are obtained. By establishing a system mathematical model and optimizing the time constant of the differential circuit, theoretically, the sub-nanosecond pulse width can be obtained. Prototype performance tests show that the power supply has a maximum frequency of 20 MHz, a minimum pulse width of 1.8 ns, and a maximum peak voltage of 10 V. By using this power supply for microhole electrochemical machining experiments, nanometer-level machining precision has been achieved.

| S-EPMC10739692 | biostudies-literature

Effects of Micromachining on Anti-oxidant Elution from a Mechanically-Adaptive Polymer.

Project description:Intracortical microelectrodes (IMEs) can be used to restore motor and sensory function as a part of brain-computer interfaces in individuals with neuromusculoskeletal disorders. However, the neuroinflammatory response to IMEs can result in their premature failure, leading to reduced therapeutic efficacy. Mechanically-adaptive, resveratrol-eluting (MARE) neural probes target two mechanisms believed to contribute to the neuroinflammatory response by reducing the mechanical mismatch between the brain tissue and device, as well as locally delivering an antioxidant therapeutic. To create the mechanically-adaptive substrate, a dispersion, casting, and evaporation method is used, followed by a microfabrication process to integrate functional recording electrodes on the material. Resveratrol release experiments were completed to generate a resveratrol release profile and demonstrated that the MARE probes are capable of long-term controlled release. Additionally, our results showed that resveratrol can be degraded by laser-micromachining, an important consideration for future device fabrication. Finally, the electrodes were shown to have a suitable impedance for single-unit neural recording and could record single units in vivo.

| S-EPMC10996452 | biostudies-literature

Real-time on-machine observations close to interelectrode gap in a tool-based hybrid laser-electrochemical micromachining process.

Project description:A tool-based hybrid laser-electrochemical micromachining process involves concurrent application of two process energies i.e. electrochemical and laser in the same machining zone by means of a hybrid tool which serves as an ECM tool as well as a multimode waveguide. It is a relatively novel process finding applications in defect-free machining of difficult-to-cut materials without affecting their microstructure. In order to understand the physical phenomena occurring during this process, in-situ observations are required. Therefore, in this work, a real time observation was carried out of a novel tool-based hybrid laser electrochemical micromachining process. A combination of high-speed imaging and Large Scale Particle Image Velocimetry (LSPIV) was used to visualize the tool-based hybrid laser-ECM process in real time. It also allowed to carry out experimental investigations on the by-products and bubble generation which have a direct effect on process performance in terms of accuracy and efficiency. The real-time on-machine observations are unique of its kind and they will facilitate the understanding of underlying mechanisms governing this hybrid laser-electrochemical micromachining process. This will ultimately help in improving the quality of parts manufactured. This research is also a step forward towards making these physics-based hybrid processes deterministic by employing high-speed imaging in a closed loop control.

| S-EPMC7544913 | biostudies-literature

Electrochemical Nitrogen Reduction: The Energetic Distance to Lithium.

Project description:Energy-efficient electrochemical reduction of nitrogen to ammonia could help in mitigating climate change. Today, only Li- and recently Ca-mediated systems can perform the reaction. These materials have a large intrinsic energy loss due to the need to electroplate the metal. In this work, we present a series of calculated energetics, formation energies, and binding energies as fundamental features to calculate the energetic distance between Li and Ca and potential new electrochemical nitrogen reduction systems. The featured energetic distance increases with the standard potential. However, dimensionality reduction using principal component analysis provides an encouraging picture; Li and Ca are not exceptional in this feature space, and other materials should be able to carry out the reaction. However, it becomes more challenging the more positive the plating potential is.

| S-EPMC11474955 | biostudies-literature

Photolithographic surface micromachining of polydimethylsiloxane (PDMS).

Project description:A major technical hurdle in microfluidics is the difficulty in achieving high fidelity lithographic patterning on polydimethylsiloxane (PDMS). Here, we report a simple yet highly precise and repeatable PDMS surface micromachining method using direct photolithography followed by reactive ion etching (RIE). Our method to achieve surface patterning of PDMS applied an O(2) plasma treatment to PDMS to activate its surface to overcome the challenge of poor photoresist adhesion on PDMS for photolithography. Our photolithographic PDMS surface micromachining technique is compatible with conventional soft lithography techniques and other silicon-based surface and bulk micromachining methods. To illustrate the general application of our method, we demonstrated fabrication of large microfiltration membranes and free-standing beam structures in PDMS.

| S-EPMC4120064 | biostudies-literature

Surface Modification of Magnetoactive Elastomers by Laser Micromachining.

Project description:It has been recently demonstrated that laser micromachining of magnetoactive elastomers is a very convenient method for fabricating dynamic surface microstructures with magnetically tunable properties, such as wettability and surface reflectivity. In this study, we investigate the impact of the micromachining process on the fabricated material's structural properties and its chemical composition. By employing scanning electron microscopy, we investigate changes in size distribution and spatial arrangement of carbonyl iron microparticles dispersed in the polydimethylsiloxane (PDMS) matrix as a function of laser irradiation. Based on the images obtained by a low vacuum secondary electron detector, we analyze modifications of the surface topography. The results show that most profound modifications occur during the low-exposure (8 J/cm2) treatment of the surface with the laser beam. Our findings provide important insights for developing theoretical models of functional properties of laser-sculptured microstructures from magnetoactive elastomers.

| S-EPMC11012975 | biostudies-literature

Non-Lithographic Silicon Micromachining Using Inkjet and Chemical Etching.

Project description:We introduce a non-lithographical and vacuum-free method to pattern silicon. The method combines inkjet printing and metal assisted chemical etching (MaCE); we call this method "INKMAC". A commercial silver ink is printed on top of a silicon surface to create the catalytic patterns for MaCE. The MaCE process leaves behind a set of silicon nanowires in the shape of the inkjet printed micrometer scale pattern. We further show how a potassium hydroxide (KOH) wet etching process can be used to rapidly etch away the nanowires, producing fully opened cavities and channels in the shape of the original printed pattern. We show how the printed lines (width 50⁻100 µm) can be etched into functional silicon microfluidic channels with different depths (10⁻40 µm) with aspect ratios close to one. We also used individual droplets (minimum diameter 30 µm) to produce cavities with a depth of 60 µm and an aspect ratio of two. Further, we discuss using the structured silicon substrate as a template for polymer replication to produce superhydrophobic surfaces.

| S-EPMC6189811 | biostudies-literature

Focused ion beam micromachining of eukaryotic cells for cryoelectron tomography.

Project description:Cryoelectron tomography provides unprecedented insights into the macromolecular and supramolecular organization of cells in a close-to-living state. However because of the limited thickness range (< 0.5-1 μm) that is accessible with today's intermediate voltage electron microscopes only small prokaryotic cells or peripheral regions of eukaryotic cells can be examined directly. Key to overcoming this limitation is the ability to prepare sufficiently thin samples. Cryosectioning can be used to prepare thin enough sections but suffers from severe artefacts, such as substantial compression. Here we describe a procedure, based upon focused ion beam (FIB) milling for the preparation of thin (200-500 nm) lamellae from vitrified cells grown on electron microscopy (EM) grids. The self-supporting lamellae are apparently free of distortions or other artefacts and open up large windows into the cell's interior allowing tomographic studies to be performed on any chosen part of the cell. We illustrate the quality of sample preservation with a structure of the nuclear pore complex obtained from a single tomogram.

| S-EPMC3311327 | biostudies-literature

Direct Micromachining of Microfluidic Channels on Biodegradable Materials Using Laser Ablation.

Project description:Laser patterning on polymeric materials is considered a green and rapid manufacturing process with low material selection barrier and high adjustability. Unlike microelectromechanical systems (MEMS), it is a highly flexible processing method, especially useful for prototyping. This study focuses on the development of polymer surface modification method using a 193 nm excimer laser system for the design and fabrication of a microfluidic system similar to that of natural vasculatures. Besides from poly(dimethyl siloxane) (PDMS), laser ablation on biodegradable polymeric material, poly(glycerol sebacate) (PGS) and poly(1,3-diamino-2-hydroxypropane-co-polyol sebacate) (APS) are investigated. Parameters of laser ablation and fabrication techniques to create microchannels are discussed. The results show that nano/micro-sized fractures and cracks are generally observed across PDMS surface after laser ablation, but not on PGS and APS surfaces. The widths of channels are more precise on PGS and APS than those on PDMS. Laser beam size and channel depth are high correlation with a linear relationship. Repeated laser ablations on the same position of scaffolds reveal that the ablation efficiencies and edge quality on PGS and APS are higher than on PDMS, suggesting the high applicability of direct laser machining to PGS and APS. To ensure stable ablation efficiency, effects of defocus distance into polymer surfaces toward laser ablation stability are investigated. The depth of channel is related to the ratio of firing frequency and ablation progression speed. The hydrodynamic simulation of channels suggests that natural blood vessel is similar to the laser patterned U-shaped channels, and the resulting micro-patterns are highly applicable in the field of micro-fabrication and biomedical engineering.

| S-EPMC6432037 | biostudies-literature

A Practical Comparison of Beam Shuttering Technologies for Pulsed Laser Micromachining Applications.

Project description:In this report we investigate the performance of various beam shutter technologies when applied to femtosecond laser micromachining. Three different shutter options are considered: a mechanical blade shutter, a bistable rotary solenoid shutter, and an electro-optic modulator (EOM) shutter. We analyzed the behavior of each shutter type during repeated open/close commands (period of 10 ≤ T ≤ 200 ms) using both high-speed videography and practical micromachining experiments. To quantify the performance at varying cycle periods, we introduce a new variable called the compliance that characterizes the average state of the shutter with respect to its intended position. We found that the solenoid shutter responds poorly to sequential commands. The mechanical shutter provides reliable performance for cycled commands as short as T = 40 ms, but begins to lag significantly behind the control signal for T ≤ 20 ms. The EOM shutter provides the most precise and reliable performance, with an opening time of only 0.6 ms and a high compliance with the signal commands, even when cycled very quickly (T = 10 ms). Overall, this study acts as an extensive practical guide for other laser users when considering different shutter options for their laser system and desired application.

| S-EPMC8839459 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data