Controllable Sliding Transfer of Wafer-Size Graphene.
Ontology highlight
ABSTRACT:
SUBMITTER: Lu W
PROVIDER: S-EPMC5039975 | biostudies-literature | 2016 Sep
REPOSITORIES: biostudies-literature
Publications
Controllable Sliding Transfer of Wafer-Size Graphene.
Lu Wenjing W Zeng Mengqi M Li Xuesong X Wang Jiao J Tan Lifang L Shao Miaomiao M Han Jiangli J Wang Sheng S Yue Shuanglin S Zhang Tao T Hu Xuebo X Mendes Rafael G RG Rümmeli Mark H MH Peng Lianmao L Liu Zhongfan Z Fu Lei L
Advanced science (Weinheim, Baden-Wurttemberg, Germany) 20160315 9
<b>The innovative design of sliding transfer</b> based on a liquid substrate can succinctly transfer high-quality, wafer-size, and contamination-free graphene within a few seconds. Moreover, it can be extended to transfer other 2D materials. The efficient sliding transfer approach can obtain high-quality and large-area graphene for fundamental research and industrial applications. ...[more]
Similar Datasets
Project description:During the past decades micro-electromechanical microphones have largely taken over the market for portable devices, being produced in volumes of billions yearly. Because performance of current devices is near the physical limits, further miniaturization and improvement of microphones for mobile devices poses a major challenge that requires breakthrough device concepts, geometries, and materials. Graphene is an attractive material for enabling these breakthroughs due to its flexibility, strength, nanometer thinness, and high electrical conductivity. Here, we demonstrate that transfer-free 7 nm thick multilayer graphene (MLGr) membranes with diameters ranging from 85-155 to 300 μm can be used to detect sound and show a mechanical compliance up to 92 nm Pa-1, thus outperforming commercially available MEMS microphones of 950 μm with compliances around 3 nm Pa-1. The feasibility of realizing larger membranes with diameters of 300 μm and even higher compliances is shown, although these have lower yields. We present a process for locally growing graphene on a silicon wafer and realizing suspended membranes of patterned graphene across through-silicon holes by bulk micromachining and sacrificial layer etching, such that no transfer is required. This transfer-free method results in a 100% yield for membranes with diameters up to 155 μm on 132 fabricated drums. The device-to-device variations in the mechanical compliance in the audible range (20-20000 Hz) are significantly smaller than those in transferred membranes. With this work, we demonstrate a transfer-free method for realizing wafer-scale multilayer graphene membranes that is compatible with high-volume manufacturing. Thus, limitations of transfer-based methods for graphene microphone fabrication such as polymer contamination, crack formation, wrinkling, folding, delamination, and low-tension reproducibility are largely circumvented, setting a significant step on the route toward high-volume production of graphene microphones.
| S-EPMC9100512 | biostudies-literature
Project description:Since the performance of micro-electro-mechanical system (MEMS)-based microphones is approaching fundamental physical, design, and material limits, it has become challenging to improve them. Several works have demonstrated graphene's suitability as a microphone diaphragm. The potential for achieving smaller, more sensitive, and scalable on-chip MEMS microphones is yet to be determined. To address large graphene sizes, graphene-polymer heterostructures have been proposed, but they compromise performance due to added polymer mass and stiffness. This work demonstrates the first wafer-scale integrated MEMS condenser microphones with diameters of 2R = 220-320 μm, thickness of 7 nm multi-layer graphene, that is suspended over a back-plate with a residual gap of 5 μm. The microphones are manufactured with MEMS compatible wafer-scale technologies without any transfer steps or polymer layers that are more prone to contaminate and wrinkle the graphene. Different designs, all electrically integrated are fabricated and characterized allowing us to study the effects of the introduction of a back-plate for capacitive read-out. The devices show high mechanical compliances Cm = 0.081-1.07 μmPa-1 (10-100 × higher than the silicon reported in the state-of-the-art diaphragms) and pull-in voltages in the range of 2-9.5 V. In addition, to validate the proof of concept, we have electrically characterized the graphene microphone when subjected to sound actuation. An estimated sensitivity of S1kHz = 24.3-321 mV Pa-1 for a Vbias = 1.5 V was determined, which is 1.9-25.5 × higher than of state-of-the-art microphone devices while having a ~9 × smaller area.
| S-EPMC10879197 | biostudies-literature
Project description:High-quality graphene-based van der Waals superlattices are crucial for investigating physical properties and developing functional devices. However, achieving homogeneous wafer-scale graphene-based superlattices with controlled twist angles is challenging. Here, we present a flat-to-flat transfer method for fabricating wafer-scale graphene and graphene-based superlattices. The aqueous solution between graphene and substrate is removed by a two-step spinning-assisted dehydration procedure with the optimal wetting angle. Proton-assisted treatment is further used to clean graphene surfaces and interfaces, which also decouples graphene and neutralizes the doping levels. Twist angles between different layers are accurately controlled by adjusting the macroscopic stacking angle through their wafer flats. Transferred films exhibit minimal defects, homogeneous morphology, and uniform electrical properties over wafer scale. Even at room temperature, robust quantum Hall effects are observed in graphene films with centimetre-scale linewidth. Our stacking transfer method can facilitate the fabrication of graphene-based van der Waals superlattices and accelerate functional device applications.
| S-EPMC10482836 | biostudies-literature
Project description:As the trajectory toward the graphene era continues, there is a compelling need to harness 2D technology further for the transformation of three-dimensional (3D) materials production and applications. Here, we resolve this challenge for one of the most widely utilized 3D materials in modern electronics─gold─using graphene-inspired fabrication technology that allows us to develop a multistep production method of ultrathin gold films. Such films demonstrate continuous morphology, low sheet resistance (10 Ω/sq), and high transparency (80%), offering opportunities in a variety of technological and scientific sectors. To this end, we demonstrate smart contact lenses and thermal camouflage based on ultrathin gold. Technologically, the record-breaking characteristics of ultrathin gold films open new horizons for flexible and transparent electrodes for photonics and optoelectronics. Most importantly, the demonstration of transferable wafer-scale ultrathin gold changes the paradigm of the field of 2D crystals and dramatically expands the range of available quasi-2D materials.
| S-EPMC11673564 | biostudies-literature
Project description:Graphene as one type of well-known solid lubricants possesses different nanotribological properties, due to the varied surface and structural characteristics caused by different preparation methods or post-processes. Graphene nanosheets with controllable surface wettability and structural defects were achieved by plasma treatment and thermal reduction. The nanotribological properties of graphene nanosheets were investigated using the calibrated atomic force microscopy. The friction force increases faster and faster with plasma treatment time, which results from the increase of surface wettability and the introduction of structural defects. Short-time plasma treatment increasing friction force is due to the enhancement of surface hydrophilicity. Longer-time plasma treatment increasing friction force can attribute to the combined effects of the enhanced surface hydrophilicity and the generated structural defects. The structural defects as a single factor also increase the friction force when the surface properties are unified by thermal reduction. The surface wettability and the nanotribological properties of plasma-treated graphene nanosheets can recover to its initial level over time. An improved spring model was proposed to elaborate the effects of surface wettability and structural defects on nanotribological properties at the atomic-scale.
| S-EPMC5282563 | biostudies-literature
Project description:Two-dimensional MoS2 is a promising material for future nanoelectronics and optoelectronics. It has remained a great challenge to grow large-size crystalline and high surface coverage monolayer MoS2. In this work, we investigate the controllable growth of monolayer MoS2 evolving from triangular flakes to continuous thin films by optimizing the concentration of gaseous MoS2, which has been shown a both thermodynamic and kinetic growth factor. A single-crystal monolayer MoS2 larger than 300 μm was successfully grown by suppressing the nuclei density and supplying sufficient source. Furthermore, we present a facile process of transferring the centimeter scale MoS2 assisted with a copper thin film. Our results show the absence of observable residues or wrinkles after we transfer MoS2 from the growth substrates onto flat substrates using this technique, which can be further extended to transfer other two-dimensional layered materials.
| S-EPMC4685646 | biostudies-literature
Project description:Graphene is one of the ideal nanomaterials to be paired with silicon, and their complementary properties can be exploited in field emission (FE) devices. We reported an efficient way to produce and adjust the dimension of uniform protrusions within graphene. First, a multistep template replication process was utilized to fabricate highly periodic and well-aligned silicon nanowires (SiNWs) of different diameters (400, 500 and 600 nm). Then, large-scale and uniform graphene, fabricated by chemical vapor deposition (CVD), was transferred onto these size-controlled SiNWs to obtain the nanoscale and uniform undulations. As compared to the nanowires alone, the hybrid structures lead to higher FE performance due to electron conductivity enhancement, high-density emmison protrusions and band bending. These hybrid SiNWs/graphene structures could provide a promising class of field emission cathodes.
| S-EPMC4609950 | biostudies-other
Project description:Wafer scale (2") BN grown by metal organic chemical vapor deposition (MOCVD) on sapphire was examined as a weakly interacting dielectric substrate for graphene, demonstrating improved transport properties over conventional sapphire and SiO2/Si substrates. Chemical vapor deposition grown graphene was transferred to BN/sapphire substrates for evaluation of more than 30 samples using Raman and Hall effects measurements. A more than 2x increase in Hall mobility and 10x reduction in sheet carrier density was measured for graphene on BN/sapphire compared to sapphire substrates. Through control of the MOCVD process, BN films with roughness ranging from <0.1 nm to >1 nm were grown and used to study the effects of substrate roughness on graphene transport. Arrays of graphene field effect transistors were fabricated on 2" BN/sapphire substrates demonstrating scalability and device performance enhancement.
| S-EPMC5996022 | biostudies-literature
Project description:Direct chemical vapor deposition (CVD) growth of wafer-scale high-quality graphene on dielectrics is of paramount importance for versatile applications. Nevertheless, the synthesized graphene is typically a polycrystalline film with high density of uncontrolled defects, resulting in a low carrier mobility and high sheet resistance. Here, we report the direct growth of highly oriented monolayer graphene films on sapphire wafers. Our growth strategy is achieved by designing an electromagnetic induction heating CVD operated at elevated temperature, where the high pyrolysis and migration barriers of carbon species are easily overcome. Meanwhile, the embryonic graphene domains are guided into good alignment by minimizing its configuration energy. The thus obtained graphene film accordingly manifests a markedly improved carrier mobility (~14,700 square centimeters per volt per second at 4 kelvin) and reduced sheet resistance (~587 ohms per square), which compare favorably with those from catalytic growth on polycrystalline metal foils and epitaxial growth on silicon carbide.
| S-EPMC8604399 | biostudies-literature
Project description:Graphene has been received a considerable amount of attention as a transparent conducting electrode (TCE) which may be able to replace indium tin oxide (ITO) to overcome the significant weakness of the poor flexibility of ITO. Given that graphene is the thinnest 2-dimensional (2D) material known, it shows extremely high flexibility, and its lateral periodic honeycomb structure of sp(2)-bonded carbon atoms enables ~2.3% of incident light absorption per layer. However, there is a trade-off between the electrical resistance and the optical transmittance, and the fixed absorption rate in graphene limits is use when fabricating devices. Therefore, a more efficient method which continuously controls the optical and electrical properties of graphene is needed. Here, we introduce a method which controls the optical transmittance and the electrical resistance of graphene through various thicknesses of the top Cu layers with a Cu/Ni metal catalyst structure used to fabricate a planar mesh pattern of single and multi-layer graphene. We exhibit a continuous transmittance change from 85% (MLG) to 97.6% (SLG) at an incident light wavelength of 550 nm on graphene samples simultaneously grown in a CVD quartz tube. We also investigate the relationships between the sheet resistances.
| S-EPMC4832197 | biostudies-literature