Flocculation of kaolin particles with cationic lignin polymers.
Ontology highlight
ABSTRACT:
SUBMITTER: Hasan A
PROVIDER: S-EPMC6389989 | biostudies-literature | 2019 Feb
REPOSITORIES: biostudies-literature
Publications
Flocculation of kaolin particles with cationic lignin polymers.
Scientific reports 20190225 1
Currently, lignin of black liquor is incinerated to generate energy in pulp mills; but it has potential to be valorized through different modification methods. In this work, kraft lignin (KL) was polymerized with 2-[(methacryloyloxy) ethyl] trimethylammonium chloride (DMC) to produce cationic water soluble polymers. After producing five polymers with different molecular weights and charge densities, their flocculation efficiency in kaolin suspensions was investigated. The adsorption, zeta potent ...[more]
Similar Datasets
Project description:The radical polymerization of acid-washed and unwashed softwood kraft lignin with [2-(methacryloyloxy) ethyl] trimethylammonium chloride (METAC) was attempted to investigate the production of lignin-based flocculants for simulated wastewater. The incorporation of METAC onto lignin resulted in a cationic charge density (2.3-3.3 meq/g), increased water solubility (89-96% in neutral pH), and increased molecular weight (70,000-210,000 g/mol) of lignin. The lignin-METAC polymers generated from acid-washed lignin had higher molecular weights than those generated from unwashed lignin. The lignin-METAC polymers showed lower resistance to thermal decomposition than unmodified lignin due to the inclusion of PolyMETAC. The unmodified acid-washed lignin samples did not significantly affect the COD of the wastewater, while the unmodified unwashed lignin samples contributed to the COD, implying that unmodified lignin was not suitable for wastewater treatment. The flocculation of wastewater with lignin-METAC led to the chemical oxygen demand (COD) reduction of 17-23% and total organic carbon (TOC) drop of 51-60%. The lignin-METAC polymer with the highest molecular weight (produced from acid-washed lignin) reached the highest COD removal, while lignin-METAC polymer with the highest charge density (produced from unwashed lignin) reached the highest TOC removal. Focused beam reflectance measurement (FBRM) studies revealed that the lignin-METAC polymer produced from acid-washed lignin with a high molecular weight generated larger and more flocs in wastewater than the lignin-METAC polymer produced from unwashed lignin. The comparison of theoretical and experimental dosages required for neutralizing the charges of wastewater demonstrated that charge neutralization was the main flocculation mechanism, although a bridging mechanism was also involved for component removals from wastewater. The use of 1 mg/L of alum along with 65 mg/L lignin-METAC in a dual coagulation-flocculation system led to higher average phosphorous (42%) and COD (44%) removals than the singular flocculation system only using 65 mg/L of lignin-METAC (with phosphorous removals of 3.4% and COD removals of 18.7%). However, lignin-METAC flocculant slightly increased the ammonia-nitrogen content in both singular flocculation and dual coagulation-flocculation systems due to the residual ammonia content of lignin-METAC. The coagulation-flocculation system determined that the use of lignin-METAC (65 mg/L) could reduce the alum dosage significantly while maintaining a similar organic content reduction of 44% for wastewater.
| S-EPMC8625770 | biostudies-literature
Project description:Purification is an essential step in many polymerization processes for fabricating highly pure polymers. This study considered various purification methods for purifying the product of lignin, acrylamide (AM), and diallyl dimethylammonium chloride (DADMAC) copolymerization reactions at a laboratory scale. The charge density, yield, molecular weight, and solubility analyses confirmed that ethanol extraction and membrane filtration were the most effective processes for producing lignin-p(AM)-p(DADMAC). The 1H NMR analysis revealed that the membrane dialysis effectively removed unreacted AM and DADMAC monomers from the reaction medium. The produced samples of the ethanol-extraction and dialysis processes had higher solubility and yield compared to the product of the acidification process. Thermogravimetric studies confirmed that the ethanol-extracted and dialyzed samples had a degradation temperature (220 °C) higher than that of the acidified samples (160 °C). The rheological studies confirmed that the viscosities of the polymer solutions were influenced more by the solubility than by the molecular weight of the generated polymers within the molecular weight range examined in this study. The flocculation studies confirmed that the ethanol-extracted and dialyzed polymers were more effective flocculants than the acidified samples for the particles of a kaolinite suspension. Based on the above results, membrane filtration with a larger pore size could be an environmentally friendly method for effectively purifying lignin-p(AM)-p(DADMAC).
| S-EPMC11525501 | biostudies-literature
Project description:Virus contamination of water is a threat to human health in many countries. Current solutions for inactivation of viruses mainly rely on environmentally burdensome chemical oxidation or energy-intensive ultraviolet irradiation, which may create toxic secondary products. Here, we show that renewable plant biomass-sourced colloidal lignin particles (CLPs) can be used as agglomeration agents to facilitate removal of viruses from water. We used dynamic light scattering (DLS), electrophoretic mobility shift assay (EMSA), atomic force microscopy and transmission electron microscopy (AFM, TEM), and UV spectrophotometry to quantify and visualize adherence of cowpea chlorotic mottle viruses (CCMVs) on CLPs. Our results show that CCMVs form agglomerated complexes with CLPs that, unlike pristine virus particles, can be easily removed from water either by filtration or centrifugation. Additionally, cationic particles formed by adsorption of quaternary amine-modified softwood kraft lignin on the CLPs were also evaluated to improve the binding interactions with these anionic viruses. We foresee that due to their moderate production cost, and high availability of lignin as a side-stream from biorefineries, CLPs could be an alternative water pretreatment material in a large variety of systems such as filters, packed columns, or flocculants.
| S-EPMC7147264 | biostudies-literature
Project description:Kraft lignin is an abundant natural resource, but it is underutilized. In this study, sulfoalkylated lignin derivatives with similar charge densities but with different alkyl chain length were produced via sulfobutylation and sulfomethylation reactions. The contact angle studies revealed that sulfobutylated lignin (SBL) with longer alkyl chains had a higher hydrophobicity than sulfomethylated lignin (SML) did. The adsorption behavior of sulfoalkylated lignins was studied using a Quartz crystal microbalance with dissipation (QCM-D) on Al2O3 coated surface as representative of positively charged sites of kaolin particles. The results of adsorption studies showed that SBL deposited more greatly than SML did on the Al2O3 surface, and it generated a thicker but less viscoelastic adlayer on the surface. The adlayer thickness and configuration of molecules on the surface were also related to the zeta potential and stabilization performance of the polymers in the kaolin suspension system. The results also confirmed that both lignin derivatives were very effective in dispersing kaolin particles at neutral pH, and their effectiveness was hampered under alkaline or acidic pH.
| S-EPMC7570282 | biostudies-literature
Project description:Sodium lignosulfonate (LS) is a lignin derivative, which has abundant resources and is an environmentally friendly raw material. In this study, cetyltrimethylammonium bromide (CTAB) and stearyltrimethylammonium bromide (STAB) were combined with LS at the isoelectric point for hydrophobic self-assembly. Transmission electron microscopy (TEM), Fourier-transform infrared (FTIR) spectroscopy, and static contact angle data proved that LS/CTAB could form colloidal spheres, while LS/STAB could not form such spheres. The impact of the molecular weight of LS on the self-assembly of LS/CTAB was investigated by using the TEM, FTIR, and static contact angle data. The obtained results showed that LS/CTAB with 10 000-50 000 Da of LS could form colloidal spheres, while LS/CTAB with 3000-5000 Da of LS could not. In addition, the TEM images revealed that the solvent plays an important role in the morphology of LS/CTAB colloidal spheres. Finally, LS/CTAB colloidal spheres were used for the encapsulation of ibuprofen (IBU). The in vitro release behavior of IBU was proven to be pH-sensitive and exhibited controlled release properties. More than 85% IBU could be preserved in simulated gastric fluid, and over 75% could be released in simulated intestinal fluid. This work provides a theoretical basis for the preparation of LS/CTAB colloidal spheres and facilitates the expansion of its applications as a drug carrier.
| S-EPMC9054004 | biostudies-literature
Project description:In wastewater treatment, flocculation is a widely used solid/liquid separation technique, which typically employs a charged polymer, a polyelectrolyte (PEL). Polyelectrolytes features, such as charge type, charge density and molecular weight, are essential parameters affecting the mechanism of flocculation and subsequent floc sedimentation. The effectiveness of the process is also influenced by the characteristics of the system (e.g., type, size, and available surface area of suspended particles, pH of the medium, charge of suspended particles). Thus, a good understanding of the flocculation kinetics, involved mechanisms and flocs structure is essential in identifying the most adequate treatment conditions, having also into consideration possible subsequent treatments. In this study, Eucalyptus bleached pulp and a cellulosic pulp with high lignin content (~4.5 wt%) obtained from Eucalyptus wood waste were used for bio-PELs production. Firstly, a pre-treatment with sodium periodate increased the pulps reactivity. To produce cationic cellulose the oxidation step was followed by the introduction of cationic groups in the cellulose chains, through reaction with Girard's reagent T. Applying different molar ratios (0.975 and 3.9) of Girard's reagent T to aldehyde groups led to cationic PELs with diverse charge density. On the other hand, to obtain anionic cellulose a sulfonation reaction with sodium metabisulfite was applied to the intermediate dialdehyde cellulose-based products, during 24 or 72 h, and anionic-PELs with diverse features were obtained. The developed water soluble, anionic and cationic bio-PELs were characterized and tested as flocculation agents for a textile industry effluent treatment. Initially, jar-tests were used to tune the most effective flocculation procedure (pH, flocculant dosage, etc.). Flocculation using these conditions was then monitored continuously, over time, using laser diffraction spectroscopy (LDS). Due to the small size of the dyes molecules, a dual system with an inorganic complexation agent (bentonite) was essential for effective decolouration of the effluent. Performance in the treatment was monitored first by turbidity removal evaluation (75-88% with cationic-PELs, 75-81% with anionic-PELs) and COD reduction evaluation (79-81% with cationic-PELs, 63-77% with anionic-PELs) in the jar tests. Additionally, the evolution of flocs characteristics (structure and size) during their growth and the flocculation kinetics, were studied using the LDS technique, applying the different PELs produced and for a range of PEL concentration. The results obtained through this monitoring procedure allowed to discuss the possible flocculation mechanisms involved in the process. The results obtained with the bio-PELs were compared with those obtained using synthetic PELs, commonly applied in effluents treatment, polyacrylamides. The developed bio-PELs can be competitive, eco-friendly flocculation agents for effluents treatment from several industries, when compared to traditional synthetic flocculants with a significant environmental footprint. Moreover, LDS proved to be a feasible technique to monitor flocculation processes, even when a real industrial effluent is being tested.
| S-EPMC7002540 | biostudies-literature
Project description:Lignin may serve as a renewable feedstock for the production of chemicals and fuels if mild, scalable processes for its depolymerization can be devised. The use of small organic thiols represents a bioinspired strategy to cleave the β-O-4 bond, the most common linkage in lignin. In the present study, synthetic β-O-4 linked polymers were treated with organic thiols, yielding up to 90 % cleaved monomer products. Lignin extracted from poplar was also treated with organic thiols resulting in molecular weight reductions as high as 65 % (Mn ) in oxidized lignin. Thiol-based cleavage of other lignin linkages was also explored in small-molecule model systems to uncover additional potential pathways by which thiols might depolymerize lignin. The success of thiol-mediated cleavage on model dimers, polymers, and biomass-derived lignin illustrates the potential utility of small redox-active molecules to penetrate complex polymer matrices for depolymerization and subsequent valorization of lignin into fuels and chemicals.
| S-EPMC7540407 | biostudies-literature
Project description:The article presents the results of the preparation and study of a gel-polymer electrolyte based on lignin obtained from Pinus sylvestris. Sulfonation and subsequent chlorination of lignin make possible implementation of the principle of mono-ionic conductivity in a natural biopolymer matrix, which provides predominantly cationic conductivity of the electrolyte. Based on the results of the qualitative and quantitative analysis of the synthesized samples, the mechanisms of the chemical conversion of the biopolymer, the structure models of the converted fragments of macromolecules, as well as the quantum-chemical calculation of their electronic and geometric parameters are presented. The key electronic characteristics of the gel polymer electrolytes (GPE) based on a composite of lignins with 20 wt.% polyvinyl alcohol are determined by impedance spectroscopy. The maximum value of the specific volume conductivity is 2.48 × 10-4 S cm-1, which is comparable with most commercial electrolytes of this type, but at the same time, record values are reached in the number of lithium cation transfer tLi+ of 0.89. The studies allow to identify the basic laws of the effect of chemical modification on the structure of GPE and describe the mechanism of ionic conductivity.
| S-EPMC8309217 | biostudies-literature
Project description:The current gold standard diagnostic for bacterial infections is the use of culture, which can be time consuming and can take up to five days for results to be reported. There is therefore an unmet clinical need for a rapid and label free alternative. This paper demonstrates a method of detecting the presence of amplified DNA from bacterial samples using a sterically-stabilised, cationic polymer latex and widely available equipment, providing an accessible alternative DNA detection technique. If DNA is present in a sample, successful amplification by polymerase chain-reaction (PCR) results in the amplified DNA inducing flocculation of the polymer latex followed by rapid sedimentation. This results in a visible and obvious change from a milky-white dispersion to a precipitated latex with a colourless and transparent supernatant, thus giving a clear visual indication of the presence or absence of amplified DNA. Specifically, the response of four polymer latexes with different morphologies to the addition of amplified bacterial DNA was investigated. Cationic latexes flocculated rapidly whereas non-ionic and anionic latexes did not, as judged by eye, disc centrifuge photosedimentometry (DCP), and UV-visible spectrophotometry. The stability of several cationic latexes with different morphologies in typical PCR reagents was investigated. It was found that unwanted flocculation occurred for a latex with a non-ionic core and a cationic corona (poly[2-vinyl pyridine-b-benzyl methacrylate], prepared by polymerisation-induced self-assembly) whereas a ∼700 nm PEGMA-stabilised P2VP latex (non-ionic stabiliser, cationic core), prepared by emulsion polymerisation remained stable. The sensitivity and rate of sedimentation of the PEGMA-stabilised P2VP latex was demonstrated by varying the sequence length and concentration of amplified DNA from Pseudomonas aeruginosa using universal bacterial primers. DNA concentrations as low as 0.78 ng μl-1 could readily be detected within 30 minutes from the addition of amplified DNA to the latex. Furthermore, the specificity of this method was demonstrated by showing a negative result occurs (no flocculation of the latex) when PCR product from a fungal (Candida albicans) sample using bacterial primers was added to the latex.
| S-EPMC10155078 | biostudies-literature
Project description:Copper-free synthesis of cationic glycidyl triazolyl polymers (GTPs) is achieved through a thermal azide-alkyne cycloaddition reaction between glycidyl azide polymer and propiolic acid, followed by decarboxylation and quaternization of the triazole unit. For synthesizing nonfunctionalized GTP (GTP-H), a microwave-assisted method enhances the decarboxylation reaction of carboxy-functionalized GTP (GTP-COOH). Three variants of cationic GTPs with different N-substituents [N-ethyl, N-butyl, and N-tri(ethylene glycol) monomethyl ether (EG3)] are synthesized. The molecular weight of GTP-H is determined via size exclusion chromatography. Thermal properties of all GTPs are characterized using differential scanning calorimetry and thermogravimetric analysis. The ionic conductivities of these cationic GTPs are assessed by impedance measurements. The conducting ion concentration and mobility are calculated based on the electrode polarization model. Among three cationic GTPs, the GTP with the N-EG3 substituent exhibits the highest ionic conductivity, reaching 6.8 × 10-6 S cm-1 at 25 °C under dry conditions. When compared to previously reported reference polymers, the reduction of steric crowding around the triazolium unit is considered to be a key factor in enhancing ionic conductivity.
| S-EPMC11661660 | biostudies-literature