Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Large datasets of single carbon and glass fibre mechanical properties obtained with automated testing equipment.

ABSTRACT: This data article presents fibre mechanical properties acquired using automated single fibre tensile testing equipment. The raw data consists of the fibre diameter, gauge length and load-displacement diagrams. A total of 690 fibres were tested across four carbon and one glass fibre type. The largest dataset, for the T700S carbon fibre, consists of 217 data points. After performing a compliance calibration, the load-displacement diagrams are converted into stress-strain diagrams from which the tensile modulus and strength are extracted. The data presented in this article can be used as input data for models or for data processing during determination of other properties experimentally. The interpretation of the data can be found in [1]. The data is hosted in the Mendeley Data repository at [2].

SUBMITTER: Mesquita F

PROVIDER: S-EPMC8114124 | biostudies-literature | 2021 Jun

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Publications

Large datasets of single carbon and glass fibre mechanical properties obtained with automated testing equipment.

Mesquita Francisco F Bucknell Steve S Leray Yann Y Lomov Stepan V SV Swolfs Yentl Y

Data in brief 20210501

This data article presents fibre mechanical properties acquired using automated single fibre tensile testing equipment. The raw data consists of the fibre diameter, gauge length and load-displacement diagrams. A total of 690 fibres were tested across four carbon and one glass fibre type. The largest dataset, for the T700S carbon fibre, consists of 217 data points. After performing a compliance calibration, the load-displacement diagrams are converted into stress-strain diagrams from which the te ...[more]

PMID: 34013010

Similar Datasets

Scanning electron microscopy datasets for local fibre volume fraction determination in non-crimp glass-fibre reinforced composites.

Project description:The fatigue damage evolution depends on the local fibre volume fraction as observed in the co-submitted publication [1]. Conventionally, fibre volume fractions are determined as an averaged overall fibre volume fraction determined from small cuts of the laminate. Alternatively, automatically stitching of scanning electron microscopy (SEM) images can make high-resolution scans of large cross-section area with large contrast between the polymer and glass-fibre phase. Therefore, local distribution of the fibre volume fraction can be characterised automatically using such scan-data. The two datasets presented here cover two large Field of Views scanning electron microscopy (SEM) images. The two images is generated from between 1200 and 1800 high-resolution scan pictures which have been stitched into two high-resolution tif-files. The resolution corresponds to between 700 and 5000 pixels covering each fibre. The datasets are coming from two different non-crimp fabric glass fibre reinforced epoxy composites typically used in the wind turbine industry. Depending on the regions analysed, fibre volume fraction in the range of 50-85% is found. The maximum local fibre volume fraction is found averaging the local fibre volume fraction over 5 × 5 fibre diameter (80 × 80 µm2) areas. The local fibre volume fraction has been used in the analysis performed in [1].

| S-EPMC7905358 | biostudies-literature

Non-isothermal crystallization kinetics of polypropylene/short glass fibre/multiwalled carbon nanotube composites.

Project description:The non-isothermal crystallization kinetics of polypropylene (PP) reinforced with multiwalled carbon nanotubes (MWCNTs) and short glass fibres (GF) was studied by differential scanning calorimetry (DSC). The glass fibre concentration was maintained at 20 wt% and the MWCNT content ranged from 1 to 5 wt% in the PP matrix. The crystallization studies performed by DSC showed an increase in crystallization rate and a decrease in half time of crystallization of PP in the presence of micro and nano fillers. The Avrami, Ozawa, and Mo models were applied to analyze the non-isothermal crystallization behavior of PP multiscale composites. The Avrami model could very well describe the crystallization behavior of PP to 70% of the completion of crystallization. Beyond that level, it deviated significantly for all composites. On the other hand, the kinetics of crystallization could be well described by the Mo model. The strongest nucleating effect and the lowest activation energy were obtained for the composite with 2 wt% MWCNT and 20 wt% glass fibre. The X-ray diffraction analysis showed a significant reduction in the average crystal size in accordance with the amount of MWCNTs added.

| S-EPMC9090750 | biostudies-literature

Large datasets of water vapor sorption, mass diffusion immersed in water, hygroscopic expansion and mechanical properties of flax fibre/shape memory epoxy hygromorph composites.

Project description:This data article presents four experimental sets of results related to flax fibre composites with epoxy shape memory polymer matrix: water vapor absorption, mass diffusion immersed in water, hygroscopic expansion, mechanical properties. The water vapor absorption tests are described in raw data related to four types of laminates with weights measured at different relative humidity (0%, 9%, 33%, 44%,75%, 85% and 100%). The mass diffusion experiments are related to weights of immersed samples over time. The unidirectional composite hygroscopic expansion is also measured along the fibre longitude and transverse directions. The mechanical properties of flax composite at various temperatures (20°C, 40°C, 60°C, 80°C and 100°C) and humidity environments (50% and immersed) are also described. Load-displacement diagrams of the hygromorph composites are converted into stress-strain diagrams via a compliance calibration, from which the tensile moduli are extracted. The data presented in this article can provide a benchmark for the development of new models, or for the determination of other properties via post processing. The detailed interpretation of the data can be found in [1]. The data is available in the Mendeley Data repository at [2].

| S-EPMC9234088 | biostudies-literature

Automated single particle detection and tracking for large microscopy datasets.

Project description:Recent advances in optical microscopy have enabled the acquisition of very large datasets from living cells with unprecedented spatial and temporal resolutions. Our ability to process these datasets now plays an essential role in order to understand many biological processes. In this paper, we present an automated particle detection algorithm capable of operating in low signal-to-noise fluorescence microscopy environments and handling large datasets. When combined with our particle linking framework, it can provide hitherto intractable quantitative measurements describing the dynamics of large cohorts of cellular components from organelles to single molecules. We begin with validating the performance of our method on synthetic image data, and then extend the validation to include experiment images with ground truth. Finally, we apply the algorithm to two single-particle-tracking photo-activated localization microscopy biological datasets, acquired from living primary cells with very high temporal rates. Our analysis of the dynamics of very large cohorts of 10 000 s of membrane-associated protein molecules show that they behave as if caged in nanodomains. We show that the robustness and efficiency of our method provides a tool for the examination of single-molecule behaviour with unprecedented spatial detail and high acquisition rates.

| S-EPMC4892463 | biostudies-literature

Setting kinetics and mechanical properties of flax fibre reinforced glass ionomer restorative materials.

Project description:Regardless of the excellent properties of glass ionomer cements, their poor mechanical properties limit their applications to non-load bearing areas. This study aimed to investigate the effect of incorporated short, chopped and randomly distributed flax fibers (0, 0.5, 1, 2.5, 5 and 25 wt%) on setting reaction kinetics, and mechanical and morphological properties of glass ionomer cements. Addition of flax fibers did not significantly affect the setting reaction extent. According to their content, flax fibers increased the compressive (from 148 to 250 MPa) and flexure strength (from 20 to 42 MPa). They also changed the brittle behavior of glass ionomer cements to a plastic one. They significantly reduced the compressive (from 3 to 1.3 GPa) and flexure modulus (from 19 to 14 GPa). Accordingly, flax fiber-modified glass ionomer cements could be potentially used in high-stress bearing areas.

| S-EPMC5460615 | biostudies-other

Comparison of two rapid automated analysis tools for large FTIR microplastic datasets.

Project description:One of the biggest issues in microplastic (MP, plastic items <5 mm) research is the lack of standardisation and harmonisation in all fields, reaching from sampling methodology to sample purification, analytical methods and data analysis. This hampers comparability as well as reproducibility among studies. Concerning chemical analysis of MPs, Fourier-transform infrared (FTIR) spectroscocopy is one of the most powerful tools. Here, focal plane array (FPA) based micro-FTIR (µFTIR) imaging allows for rapid measurement and identification without manual preselection of putative MP and therefore enables large sample throughputs with high spatial resolution. The resulting huge datasets necessitate automated algorithms for data analysis in a reasonable time frame. Although solutions are available, little is known about the comparability or the level of reliability of their output. For the first time, within our study, we compare two well-established and frequently applied data analysis algorithms in regard to results in abundance, polymer composition and size distributions of MP (11-500 µm) derived from selected environmental water samples: (a) the siMPle analysis tool (systematic identification of MicroPlastics in the environment) in combination with MPAPP (MicroPlastic Automated Particle/fibre analysis Pipeline) and (b) the BPF (Bayreuth Particle Finder). The results of our comparison show an overall good accordance but also indicate discrepancies concerning certain polymer types/clusters as well as the smallest MP size classes. Our study further demonstrates that a detailed comparison of MP algorithms is an essential prerequisite for a better comparability of MP data.

| S-EPMC10284987 | biostudies-literature

damidseq_pipeline: an automated pipeline for processing DamID sequencing datasets

Project description:DamID is a powerful technique for identifying regions of the genome bound by a DNA-binding (or DNA-associated) protein. Currently no method exists for automatically processing next-generation sequencing DamID (DamID-seq) data, and the use of DamID-seq datasets with normalisation based on read-counts alone can lead to high background and the loss of bound signal. DamID-seq thus presents novel challenges in terms of normalisation and background minimisation. We describe here damidseq_pipeline, a software pipeline that performs automatic normalisation and background reduction on multiple DamID-seq FASTQ or BAM datasets. Single replicate profiling of pol II occupancy in 3rd instar larval neuroblasts of Drosophila

2015-06-26 | E-GEOD-69184 | biostudies-arrayexpress

A scalable and modular automated pipeline for stitching of large electron microscopy datasets.

Project description:Serial-section electron microscopy (ssEM) is the method of choice for studying macroscopic biological samples at extremely high resolution in three dimensions. In the nervous system, nanometer-scale images are necessary to reconstruct dense neural wiring diagrams in the brain, so -called connectomes. The data that can comprise of up to 108 individual EM images must be assembled into a volume, requiring seamless 2D registration from physical section followed by 3D alignment of the stitched sections. The high throughput of ssEM necessitates 2D stitching to be done at the pace of imaging, which currently produces tens of terabytes per day. To achieve this, we present a modular volume assembly software pipeline ASAP (Assembly Stitching and Alignment Pipeline) that is scalable to datasets containing petabytes of data and parallelized to work in a distributed computational environment. The pipeline is built on top of the Render Trautman and Saalfeld (2019) services used in the volume assembly of the brain of adult Drosophila melanogaster (Zheng et al. 2018). It achieves high throughput by operating only on image meta-data and transformations. ASAP is modular, allowing for easy incorporation of new algorithms without significant changes in the workflow. The entire software pipeline includes a complete set of tools for stitching, automated quality control, 3D section alignment, and final rendering of the assembled volume to disk. ASAP has been deployed for continuous stitching of several large-scale datasets of the mouse visual cortex and human brain samples including one cubic millimeter of mouse visual cortex (Yin et al. 2020); Microns Consortium et al. (2021) at speeds that exceed imaging. The pipeline also has multi-channel processing capabilities and can be applied to fluorescence and multi-modal datasets like array tomography.

| S-EPMC9427110 | biostudies-literature

Mineral-Based Coating of Plasma-Treated Carbon Fibre Rovings for Carbon Concrete Composites with Enhanced Mechanical Performance.

Project description:Surfaces of carbon fibre roving were modified by means of a low temperature plasma treatment to improve their bonding with mineral fines; the latter serving as an inorganic fibre coating for the improved mechanical performance of carbon reinforcement in concrete matrices. Variation of the plasma conditions, such as gas composition and treatment time, was accomplished to establish polar groups on the carbon fibres prior to contact with the suspension of mineral particles in water. Subsequently, the rovings were implemented in a fine concrete matrix and their pull-out performance was assessed. Every plasma treatment resulted in increased pull-out forces in comparison to the reference samples without plasma treatment, indicating a better bonding between the mineral coating material and the carbon fibres. Significant differences were found, depending on gas composition and treatment time. Microscopic investigations showed that the samples with the highest pull-out force exhibited carbon fibre surfaces with the largest areas of hydration products grown on them. Additionally, the coating material ingresses into the multifilament roving in these specimens, leading to better force transfer between individual carbon filaments and between the entire roving and surrounding matrix, thus explaining the superior mechanical performance of the specimens containing appropriately plasma-treated carbon roving.

| S-EPMC5506985 | biostudies-other

hcapca: Automated Hierarchical Clustering and Principal Component Analysis of Large Metabolomic Datasets in R.

Project description:Microbial natural product discovery programs face two main challenges today: rapidly prioritizing strains for discovering new molecules and avoiding the rediscovery of already known molecules. Typically, these problems have been tackled using biological assays to identify promising strains and techniques that model variance in a dataset such as PCA to highlight novel chemistry. While these tools have shown successful outcomes in the past, datasets are becoming much larger and require a new approach. Since PCA models are dependent on the members of the group being modeled, large datasets with many members make it difficult to accurately model the variance in the data. Our tool, hcapca, first groups strains based on the similarity of their chemical composition, and then applies PCA to the smaller sub-groups yielding more robust PCA models. This allows for scalable chemical comparisons among hundreds of strains with thousands of molecular features. As a proof of concept, we applied our open-source tool to a dataset with 1046 LCMS profiles of marine invertebrate associated bacteria and discovered three new analogs of an established anticancer agent from one promising strain.

| S-EPMC7407629 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data