Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

The experimental and finite element analysis data of Cu-UV glue composite materials.

ABSTRACT: Five different layered-fiber reinforced Cu-UV glue composite structures were prepared, with Cu plate and wire as the reinforcing phase, and UV glue as the substrate. The volume ratio of Cu and UV glue of these structures is the same, but the difference lies in the number and diameter of Cu wires. Three-point bending tests were performed on these structures, and the bending stress-bending strain curves of different structures were measured. At the same time, the finite element method is used to simulate the three-point bending test process of different structures, and the bending stress-bending strain curves of different structures were calculated. Then the experimental and simulated strengths corresponding to different structures were obtained from the stress-strain curves obtained by experiment and simulation. These data are supplementary material for the associated research article [1].

SUBMITTER: Chen X

PROVIDER: S-EPMC8473658 | biostudies-literature | 2021 Oct

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Publications

The experimental and finite element analysis data of Cu-UV glue composite materials.

Chen Xiaoyong X Hao Zhixiu Z

Data in brief 20210920

Five different layered-fiber reinforced Cu-UV glue composite structures were prepared, with Cu plate and wire as the reinforcing phase, and UV glue as the substrate. The volume ratio of Cu and UV glue of these structures is the same, but the difference lies in the number and diameter of Cu wires. Three-point bending tests were performed on these structures, and the bending stress-bending strain curves of different structures were measured. At the same time, the finite element method is used to s ...[more]

PMID: 34604481

Similar Datasets

Finite Element Analysis of Strengthening Mechanism of Ultrastrong and Tough Cellulosic Materials.

Project description:Superior strong and tough structural materials are highly desirable in engineering applications. However, it remains a big challenge to combine these two mutually exclusive mechanical properties into one body. In the work, an ultrastrong and tough cellulosic material was fabricated by a two-step process of delignification and water molecule-induced hydrogen bonding under compression. The strong and tough cellulosic material showed enhanced tensile strength (352 MPa vs. 56 MPa for natural wood) and toughness (4.1 MJ m-3 vs. 0.42 MJ m-3 for natural wood). The mechanical behaviors of ultrastrong and tough bulk material in a tensile state were simulated by finite element analysis (FEA) using mechanical parameters measured in the experiment. FEA results showed that the tensile strength and toughness gradually simultaneously improved with the increase in moisture content, demonstrating that water molecules played an active role in fabricating strong and tough materials, by plasticizing and forming hydrogen bonding among cellulose nanofibrils.

| S-EPMC9654337 | biostudies-literature

Biomechanical performance of resin composite on dental tissue restoration: A finite element analysis.

Project description:This study investigates the biomechanical performance of various dental materials when filled in different cavity designs and their effects on surrounding dental tissues. Finite element models of three infected teeth with different cavity designs, Class I (occlusal), Class II mesial-occlusal (MO), and Class II mesio-occluso-distal (MOD) were constructed. These cavities were filled with amalgam, composites (Young's moduli of 10, 14, 18, 22, and 26 GPa), and glass carbomer cement (GCC). An occlusal load of 600 N was distributed on the top surface of the teeth to carry out simulations. The findings revealed that von Mises stress was higher in GCC material, with cavity Class I (46.01 MPa in the enamel, 23.61 MPa in the dentin), and for cavity Class II MO von Mises stress was 43.64 MPa, 39.18 MPa in enamel and dentin respectively, while in case of cavity Class II MOD von Mises stress was 44.67 MPa in enamel, 27.5 in the dentin. The results showed that higher stresses were generated in the non-restored tooth compared to the restored one, and increasing Young's modulus of restorative composite material decreases stresses in enamel and dentin. The use of composite material showed excellent performance which can be a good viable option for restorative material compared to other restorative materials.

| S-EPMC10734934 | biostudies-literature

Experimental and Finite Element Data of T-joints with Circular-Hollow-Section chord members

Project description: Not available

| S-EPMC10912331 | biostudies-literature

Enhancing biomedical data validity with standardized segmentation finite element analysis.

Project description:Finite element analysis is a powerful computational technique for augmenting biomedical research, prosthetics design, and preoperative surgical assessment. However, the validity of biomechanical data obtained from finite element analysis is dependent on the quality of the preceding data processing. Until now, little information was available about the effect of the segmentation process on finite element models and biomechanical data. The current investigation applied 4 segmentation approaches to 129 femur specimens, yielding a total of 516 finite element models. Biomechanical data including average displacement, pressure, stress, and strain were collected from experimental groups based on the different segmentation approaches. The results indicate that only a 5.0% variation in the segmentation process leads to statistically significant differences in all 4 biomechanical measurements. These results suggest that it is crucial for consistent segmentation procedures to be applied to all specimens within a study. This methodological advancement will help to ensure that finite element data will be more accurate and that research conclusions will have greater validity.

| S-EPMC9198234 | biostudies-literature

Additively Manufactured Composite Lug with Continuous Carbon Fibre Steering Based on Finite Element Analysis.

Project description:In this study, the influence of curvilinear fibre reinforcement on the load-carrying capacity of additively manufactured continuous carbon fibre reinforced necked double shear lugs was investigated. A curvilinear fibre placement is descriptive of layers in extrusion-based continuous-fibre-reinforced additive manufacturing with carbon fibres aligned in the directions of principal stress. The alternating layered fibre trajectories follow the maximum and minimum principal stress directions due to axial tension loading derived from two-dimensional finite element analysis (FEA). The digital image correlation was utilised to monitor the strain distribution during the application of tensile load. The 2D FEA data and the tensile test results obtained were comparable, the part strength and the linear approximation of stiffness data variability were minimal and well within the acceptable range. Nondestructive fractography was performed by utilising computed tomography (CT) to analyse the fractured regions of the tensile-tested lug. The CT scanned images aided in deducing the failure phenomenon in layered lugs; process-induced voids and fibre layup undulation were identified as the cause for lug failure.

| S-EPMC8911614 | biostudies-literature

Experimental and Finite Element Investigations of Damage Resistance in Biomimetic Composite Sandwich T-Joints.

Project description:Composite sandwich structural joints, such as T-joints, are used in many different composite applications to transfers the load orthogonally between two sandwich elements. However, these joints connecting the sections can represent the weakest link in sandwich composite structures due to the lack of reinforcement in the out-of-plane direction. Therefore, this paper presents a new methodology for the design and analysis of composite sandwich T-joints using new biomimetic fabrication methods. The fabricated idea comes from biological fixed joints as an evolutionary alteration processes of trunk-branches of trees. It offers unique attributes to optimize the continuous fiber paths for minimum stress concentrations and multi-sandwich layers to increase the bending stiffness and strength. The focus is on how the biomimetic technique can improve sandwich T-joint structures by increasing their strength and load carrying capability without adding a significant weight penalty. The major attention is to investigate the comprehensive failure modes in the joint numerically and verified by experiments. Investigations were conducted on three different designs of biomimetic composite sandwich T-joints under tension and bending loads. The results show significant improvements to the ultimate load up to 68% in the case of bending load and 40% in the case of pull-off load in the biomimetic sandwich T-joints compared to the reference conventional T-joint design. The final failure was significantly deferred in both load status. The FE models provided important insights into the core failure and delamination of multi-interface biomimetic T-joints.

| S-EPMC5456861 | biostudies-other

Constitutive Behavior and Finite Element Analysis of FRP Composite and Concrete Members.

Project description:The present study concerns compressive and flexural constitutive models incorporated into an isoparametric beam finite element scheme for fiber reinforced polymer (FRP) and concrete composites, using their multi-axial constitutive behavior. The constitutive behavior of concrete was treated in triaxial stress states as an orthotropic hypoelasticity-based formulation to determine the confinement effect of concrete from a three-dimensional failure surface in triaxial stress states. The constitutive behavior of the FRP composite was formulated from the two-dimensional classical lamination theory. To predict the flexural behavior of circular cross-section with FRP sheet and concrete composite, a layered discretization of cross-sections was incorporated into nonlinear isoparametric beam finite elements. The predicted constitutive behavior was validated by a comparison to available experimental results in the compressive and flexural beam loading test.

| S-EPMC5452671 | biostudies-other

Data for the stress update assessment in large-deformation finite element analysis.

Project description:During a research work about stress integration schemes for large-deformation finite element analysis many datasets are collected from both numerical and analytical models. The corresponding numerical data (stress and displacements) are computed by means of different finite element formulations including the well-established stress update schemes employed by the major commercial software packages. To this purpose a suitable finite element code, capable of easily switching the different methods, is implemented. Accordingly, the data computed for three stress integration tests allowing analytical solution in the case of linear material are presented. The comparison of all the predictions from the various methods allows the choice of the most accurate model in predicting displacement and related stress. In addition, the data may be reused as starting point in the development of new stress integration strategies, as a reference comparison to understand the behaviour of the standard methods.

| S-EPMC10792682 | biostudies-literature

Finite Element Analysis of Fracture Fixation.

Project description:Purpose of reviewFracture fixation aims to provide stability and promote healing, but remains challenging in unstable and osteoporotic fractures with increased risk of construct failure and nonunion. The first part of this article reviews the clinical motivation behind finite element analysis of fracture fixation, its strengths and weaknesses, how models are developed and validated, and how outputs are typically interpreted. The second part reviews recent modeling studies of the femur and proximal humerus, areas with particular relevance to fragility fractures.Recent findingsThere is some consensus in the literature around how certain modeling aspects are pragmatically formulated, including bone and implant geometries, meshing, material properties, interactions, and loads and boundary conditions. Studies most often focus on predicted implant stress, bone strain surrounding screws, or interfragmentary displacements. However, most models are not rigorously validated. With refined modeling methods, improved validation efforts, and large-scale systematic analyses, finite element analysis is poised to advance the understanding of fracture fixation failure, enable optimization of implant designs, and improve surgical guidance.

| S-EPMC8422380 | biostudies-literature

Biomechanical evaluation of unilateral subcondylar fracture of the mandible on the varying materials: A finite element analysis.

Project description:Fixation materials used in the surgical treatment of subcondylar fractures contribute to successful clinical outcomes. In this study, we simulated the mechanical properties of four fixation materials [titanium (Ti), magnesium alloy (Mg alloy), poly-L-lactic acid (PLLA), and hydroxyapatite/poly-L-lactide (HA-PLLA)] in a finite-element analysis model of subcondylar fracture. Two four-hole plates were fixed on the anterior and posterior surfaces of the subcondyle of the mandible. In the simulation model of a subcondylar fracture, we evaluated the stress distribution and mechanical deformation of fixation materials. The stress distribution conspicuously appeared on the condylar neck of the non-fractured side and the center of the anterior plate for all materials. More stress distribution to the biologic component appeared with HA-PLLA than with Ti or Mg alloy, but its effects were less prominent than that of PLLA. The largest deformation was observed with PLLA, followed by HA-PLLA, Mg alloy, and Ti. The results of the present study imply the clinical potential of the HA-PLLA fixation material for open reduction of subcondylar fractures.

| S-EPMC7544122 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data