Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Influence of the Deep Cryogenic Treatment on AISI 52100 and AISI D3 Steel's Corrosion Resistance.

ABSTRACT: The effect of deep cryogenic treatment (DCT) on corrosion resistance of steels AISI 52100 and AISI D3 is investigated and compared with conventional heat-treated counterparts. DCT's influence on microstructural changes is subsequently correlated to the corrosion resistance. DCT is confirmed to reduce the formation of corrosion products on steels' surface, retard the corrosion products development and propagation. DCT reduces surface cracking, which is considered to be related to modified residual stress state of the material. DCT's influence on each steel results from the altered microstructure and alloying element concentration that depends on steel matrix and type. This study presents DCT as an effective method for corrosion resistance alteration of steels.

SUBMITTER: Jovicevic-Klug P

PROVIDER: S-EPMC8585173 | biostudies-literature | 2021 Oct

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Publications

Influence of the Deep Cryogenic Treatment on AISI 52100 and AISI D3 Steel's Corrosion Resistance.

Jovičević-Klug Patricia P Kranjec Tjaša T Jovičević-Klug Matic M Kosec Tadeja T Podgornik Bojan B

Materials (Basel, Switzerland) 20211024 21

The effect of deep cryogenic treatment (DCT) on corrosion resistance of steels AISI 52100 and AISI D3 is investigated and compared with conventional heat-treated counterparts. DCT's influence on microstructural changes is subsequently correlated to the corrosion resistance. DCT is confirmed to reduce the formation of corrosion products on steels' surface, retard the corrosion products development and propagation. DCT reduces surface cracking, which is considered to be related to modified residua ...[more]

PMID: 34771881

Similar Datasets

Corrosion and microstructural analysis data for AISI 316L and AISI 347H stainless steels after exposure to a supercritical water environment.

Project description:This article presents corrosion data and microstructural analysis data of austenitic stainless steels AISI 316L and AISI 347H exposed to supercritical water (25 MPa, 550 °C) with 2000 ppb of dissolved oxygen. The corrosion tests lasted a total of 1200 h but were interrupted at 600 h to allow measurements to be made. The microstructural data have been collected in the grain interior and at grain boundaries of the bulk of the materials and at the superficial oxide layer developed during the corrosion exposure.

| S-EPMC4845079 | biostudies-literature

Microbiologically influenced corrosion of AISI 202 and 316L stainless steels under manganese-oxidizing biofilms.

Project description:In this work, we study the microbiologically influenced corrosion (MIC) of AISI 316L (1-2% Mn) and AISI 202 (8-12% Mn) in the presence of manganese-oxidizing biofilms. Microbiological and 16S rRNA amplicon sequencing analysis on biofilms formed on the surfaces of both the SS materials after exposure to seawater for two months showed the presence of predominant Mn-oxidizing bacteria (MnOB) groups. The Mn contents in the biofilms formed on AISI 202 and 316L were 0.577 and 0.193 ppm, respectively. Mixed biofilms of 11 pure axenic cultures of MnOB isolated and identified from both the SS biofilms were used for MIC studies on SS. Electrochemical studies showed four orders of magnitude high icorr values (1.271 × 10-4 A.cm-2) and the onset of crevice corrosion potentials (502 mV) confirming the localized corrosion of AISI 202 and 316L, respectively, under MnOB biofilms. X-ray photoelectron spectroscopic (XPS) analysis on biotic surfaces showed a reduced Mn content from 10.1 to 7.9 atom.% confirming the Mn oxidation in AISI 202. This study confirms that MnOB biofilms on the SS surfaces can lead to MIC due to biogenic Mn oxidation, depletion of Fe and Mn content, and enrichment of Cr content.Supplementary informationThe online version contains supplementary material available at 10.1007/s13205-023-03845-z.

| S-EPMC10719233 | biostudies-literature

Datasets on the corrosion behaviour of nanostructured AISI 316 stainless steel treated by SMAT.

Project description:The present paper contains the experimental datasets on the corrosion behaviour of nanostructured AISI 316 stainless steel (SS) through polarization tests in 0.6 M NaCl aqueous solution at room temperature. The nanostructured layers were first obtained through surface mechanical attrition treatment (SMAT) method and the data information on the corrosion behaviour of the nanostructured layer was thereafter collected. Through potentiodynamic polarization tests and electrochemical impedance spectroscopy (EIS) studies, the experimental datasets were obtained to investigate the combined effects of SMAT and low temperature annealing on the corrosion behaviour of 316 SS. The experimental datasets obtained include the open circuit potential (OCP), corrosion current densities, corrosion potential, Nyquist, impedance and phase angle. The datasets provided in this article will be of great help to most aerospace, automobile, and manufacturing industries in determining the actual and practical corrosion behaviour of AISI 316 SS in corrosive and aggressive environment.

| S-EPMC6554219 | biostudies-literature

Corrosion Behavior of AISI 1045 Steel in Seawater in the Presence of Flavobacterium sp.

Project description:A systematic comparison study was carried out to investigate the effect of Flavobacterium sp. on AISI 1045 steel corrosion by weight loss, fluorescence microscopy (FM), surface analysis, cell count, pH measure, electrochemical impedance spectroscopy (EIS), and polarization curves. The impedances were considerably increased by Flavobacterium sp. between 1 and 7 day exposure and after 30 day exposure but considerably decreased by Flavobacterium sp. after 15 and 21 day exposure, which were supported by the Icorr results and the weight loss data. Furthermore, the biofilm was formed on the coupons. The pH values were considerably decreased by Flavobacterium sp. after 15 and 21 day exposure. The results proved that Flavobacterium sp. decreased the corrosion rates between 1 and 7 day exposure and after 30 day exposure and increased the corrosion rates between 15 and 21 day exposure, which could be ascribed to the protective biofilm and the secreted corrosive acid, respectively. In addition, Flavobacterium sp. considerably increased the pit numbers, the maximum pit depths, and the corresponding widths and considerably decreased the Epit values. Importantly, the coverage and the heterogeneity of the biofilm were positively correlated with the increases in the maximum pit depths and the corresponding widths and the decreases in the Epit values by Flavobacterium sp. The results demonstrated that Flavobacterium sp. increased the pitting corrosion, which could involve the heterogeneous biofilm cover.

| S-EPMC7062711 | biostudies-literature

Chloride corrosion behavior on heating pipeline made by AISI 304 and 316 in reclaimed water.

Project description:In order to transport reclaimed water safely through stainless steel (SS) heat-supply pipeline networks during their idle period, one must understand the degree to which chlorine in reclaimed water is corrosive to SS. In this study, electrochemical methods were used to evaluate the corrosion resistances of two types of SS materials, AISI 304 and AISI 316, in simulated reclaimed water at chloride concentrations of 25 to 400 mg L-1, which are similar to those present in practice. The differences in corrosion resistance between the two types of SS material were investigated using electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization tests (Tafel curves). The passivation layers on the two types of SS exhibited obvious similarities under several experimental conditions. However, EIS, polarization resistance, effective capacitance, Tafel curve, and Scanning Electron Microscope (SEM) data showed that AISI 316 has better corrosion resistance than AISI 304. The corrosion behaviours could be described as a series of reactions between Fe, Cr, and H2O that generate several precipitated products such as Fe2O3, Cr2O3, FeOOH, and CrOOH.

| S-EPMC9044296 | biostudies-literature

Evolution of the Corrosion Products around MnS Embedded in AISI 304 Stainless Steel in NaCl Solution.

Project description:The characterization and evolution of corrosion products deposited on/around MnSs, a typical kind of inclusive particle embedded in AISI 304 stainless steel, was analyzed using a quasi-in-situ method in a 3.5 wt.% NaCl solution. On/around the MnS inclusion, a corrosion product layer with spinel Fe3-xCrxO4 as the main component was formed, with a thickness of several hundred nanometers. Below the layer, there was a cavity layer in which part of the MnS remained, forming secondary pitting along the MnS/matrix boundary. The mechanism of corrosion product deposition and evolution accompanied by MnS dissolution, as well as the characteristics of the corrosion products, are discussed.

| S-EPMC11356085 | biostudies-literature

Effect of Deep Cryogenic Treatment on Wear and Galling Properties of High-Speed Steels.

Project description:New approaches to improving wear resistance with an affordable and noncomplex technology, such as deep cryogenic treatment, (DCT0), are receiving attention. The aim of this study is to investigate the effect of DCT on the friction and wear performance of high-speed steels. AISI M2, AISI M3:2 and AISI M35 were heat-treated under different conditions, and then investigated under dry sliding conditions. Tribological testing involved different contact conditions, prevailing wear mechanisms and loading conditions. The DCT effect on sliding wear resistance depends on HSS steel grade, as well as contact conditions and wear mode, whereas it improves the dynamic impact of the wear and galling resistance.

| S-EPMC8705678 | biostudies-literature

Corrosion Behavior of AISI 304 Stainless Steel Reinforcements in SCBA-SF Ternary Ecological Concrete Exposed to MgSO4.

Project description:In this study, ternary ecological concrete (TEC) mixtures were produced with partial substitution of the ordinary Portland cement (OPC) by 10%, 20%, and 30% of sugar cane bagasse ash (SCBA) and silica fume (SF); a control mixture (100% OPC) was prepared according to ACI 211.1 standard. The studied TEC specimens were reinforced with AISI 304 stainless steel and AISI 1018 carbon steel rebars. TEC reinforced specimens were immersed in two different electrolytes, a control (DI-water) and 3.5 wt.% MgSO4 solution, for 180 days. The electrochemical corrosion was monitored by corrosion potential (Ecorr) according to ASTM C-876-15 standard, and the linear polarization resistance (LPR) technique using ASTM G59 standard. The Ecorr and current density icorr results show that AISI 304 stainless steel rebars have a high corrosion resistance, with icorr values below 0.1 µA/cm2, which is interpreted as a level of negligible corrosion. The best corrosion performance was found for the TEC mixture made with a 20% addition of blend of sugar cane bagasse ash-silica fume (SCBA-SF) to the OPC.

| S-EPMC7288276 | biostudies-literature

Influence of Friction Stir Surface Processing on the Corrosion Resistance of Al 6061.

Project description:In this work, friction stir processing using a pinless tool with a featured shoulder was performed to alter the surface properties of Al 6061-O, focusing on the effect of tool traverse speed on surface properties, i.e., microstructure, hardness, and corrosion resistance. All processed samples showed refinement in grain size, microhardness, and corrosion resistance compared to the base material. Increasing tool-traverse speed marginally refined the microstructure, but produced a significant reduction in microhardness. Electrochemical impedance spectroscopy, linear polarization resistance, and potentiodynamic polarization were used to evaluate the effect of the processing conditions on corrosion behavior in a saline environment. All corrosion test results are found to agree and were supported with pictures of corroded samples captured using a field emission scanning electron microscope. A remarkable reduction in the corrosion rate was obtained with increasing traverse speed. At the highest traverse speed, the corrosion current density dropped by approximately 600 times when compared with that of the base alloy according to potentiodynamic polarization results. This is mainly due to the grain refinement produced by the friction stir process.

| S-EPMC9696715 | biostudies-literature

The Influence of Heat Treatment on the Mechanical Properties and Corrosion Resistance of the Ultrafine-Grained AA7075 Obtained by Hydrostatic Extrusion.

Project description:In this paper, the corrosion resistance and mechanical properties of the 7075 aluminum alloy are studied. The alloy was deformed by hydrostatic extrusion and then aged both naturally and artificially. Results are compared with those of coarse-grained material subjected to T6 heat treatment. The aim of the research is to find the optimal correlation between the mechanical properties and the corrosion resistance of the alloy. To this end, static tensile tests with subsequent fractography, open circuit potential, and potentiodynamic polarization tests in 0.05 M NaCl were conducted. Obtained results show that a combination of precipitate hardening and a deformed microstructure leads to increased mechanical strength with high anisotropy due to the presence of fibrous grains. Plastic deformation increases susceptibility to corrosion due to the increased number of grain boundaries, which act as paths along that corrosion propagates. However, further artificial aging incurs a positive effect on corrosion resistance due to changes in the chemical composition of the matrix as a result of the precipitation process.

| S-EPMC9228351 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data