Dataset Information

Humulus scandens-Derived Biochars for the Effective Removal of Heavy Metal Ions: Isotherm/Kinetic Study, Column Adsorption and Mechanism Investigation.

ABSTRACT: Humulus scandens was first adopted as a biomass precursor to prepare biochars by means of a facile molten salt method. The optimized biochar exhibits a high specific surface area of ~450 m2/g, a rich porous structure and abundant oxygen functional groups, which demonstrate excellent adsorption performance for heavy metal ions. The isotherm curves fit well with the Langmuir models, indicating that the process is governed by the chemical adsorption, and that the maximum adsorption capacity can reach 748 and 221 mg/g for Pb2+ and Cu2+, respectively. In addition, the optimized biochar demonstrates good anti-interference ability and outstanding removal efficiency for Cu2+ and Pb2+ in simulated wastewater. The mechanism investigation and DFT calculation suggest that the oxygen functional groups play dominant roles in the adsorption process by enhancing the binding energy towards the heavy metal ions. Meanwhile, ion exchange also serves as the main reason for the effective removal.

SUBMITTER: Bai X

PROVIDER: S-EPMC8704399 | biostudies-literature | 2021 Nov

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Humulus scandens-Derived Biochars for the Effective Removal of Heavy Metal Ions: Isotherm/Kinetic Study, Column Adsorption and Mechanism Investigation.

Bai Xingang X Xing Luyang L Liu Ning N Ma Nana N Huang Kexin K Wu Dapeng D Yin Mengmeng M Jiang Kai K

Nanomaterials (Basel, Switzerland) 20211130 12

Humulus scandens was first adopted as a biomass precursor to prepare biochars by means of a facile molten salt method. The optimized biochar exhibits a high specific surface area of ~450 m2/g, a rich porous structure and abundant oxygen functional groups, which demonstrate excellent adsorption performance for heavy metal ions. The isotherm curves fit well with the Langmuir models, indicating that the process is governed by the chemical adsorption, and that the maximum adsorptio ...[more]

PMID: 34947605

Similar Datasets

Project description:Oil palm trunk (OPT) represents one of the five main oil palm biomass wastes with high carbon content that can be economically converted to a large surface area, porous activated carbon (AC) adsorbent to treat palm oil mill effluent wastewater in Indonesia and Malaysia. In the first portion of this work, the design of the experiment was used to determine the optimum set of synthesis parameters required to maximize the iodine number of AC [i.e., Brunauer-Emmett-Teller (BET) specific surface area indicator] prepared from OPT via chemical activation route using H3PO4. The iodine numbers of AC and AC yield were probed as the impregnation ratio, the activation time, and the activation temperature were varied in the range of 0.28-3.47, 5.68-69.32 min, and 379-521 °C, respectively. An impregnation ratio of 2.29, an activation time of 6 min, and an activation temperature of 450 °C were identified as the optimum set of synthesis parameters. In the second portion of the work, the AC synthesized using the optimum parameters were then characterized and tested as an adsorbent for tannin. N2 sorption results revealed that the AC exhibits type IV isotherm, that is, contains micropores and mesopores and displays a relatively high BET specific surface area of 1657 m2 g-1. Adsorption equilibria isotherms for tannin adsorption onto the AC were collected at three different pH of 2, 4, and 6 and were nonlinearly fitted using Langmuir and Freundlich isotherm models, where the Langmuir isotherm gave better fitting than Freundlich. The higher adsorption capacity at lower pH can be explained in terms of the absence of electrostatic repulsion interaction between the AC surface and the tannic acid species as suggested by the point of zero charges (pHpzc) of 4.8 and an increasing ionization of tannic acid with pH rise between 4 and 7. Adsorption kinetics data were also obtained at four different pH of 2, 4, 6, and 8 where the nonlinear pseudo-first-order model best fitted the kinetic at pH of 2 and the nonlinear pseudo-second-order model represented the kinetic best at the remaining higher pH, which suggests that tannin adsorption onto AC occurred by physisorption at pH of 2 and by chemisorption at pH of 4, 6, and 8.

Dataset Information

Humulus scandens-Derived Biochars for the Effective Removal of Heavy Metal Ions: Isotherm/Kinetic Study, Column Adsorption and Mechanism Investigation.

Publications

<i>Humulus scandens</i>-Derived Biochars for the Effective Removal of Heavy Metal Ions: Isotherm/Kinetic Study, Column Adsorption and Mechanism Investigation.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets