Self-encapsulation liquid metal materials for flexible and stretchable electrical conductors.
Ontology highlight
ABSTRACT:
SUBMITTER: Fu JH
PROVIDER: S-EPMC9074125 | biostudies-literature | 2019 Oct
REPOSITORIES: biostudies-literature
Publications
Self-encapsulation liquid metal materials for flexible and stretchable electrical conductors.
Fu Jun-Heng JH Gao Jian-Ye JY Chen Sen S Qin Peng P Shi Jin-Tao JT Liu Jing J
RSC advances 20191030 60
A one-step strategy for fabricating flexible conductors <i>via</i> phase separation is proposed, wherein, the liquid metal was implanted into polydimethylsiloxane, whose viscosity was changed using hexane. Such self-encapsulating composite exhibited good electronic and mechanical stability under mechanical cycles with no significant leaking of droplets during the testing process. ...[more]
Similar Datasets
Project description:Crack control strategies have been proven very useful for enhancing the stretchability of metal film-based stretchable conductors. However, existing strategies often suffer from the drawbacks of complicated preparation and predefined effective directions. Here, we propose a crack compensation strategy for preparing conductors featured with high stretchability by using liquid metal microparticles (LMMPs)-embedded polydimethylsiloxane (PDMS) as the substrate with a thin film of gold (Au) sputtered on the surface. LMMPs can be elongated to connect the cracked Au film upon stretching, which can form a conductive "island-tunnel" (IT) architecture to compensate for the cracks and maintain the conductivity. The high performance of the stretchable conductor is demonstrated by using it as electrodes to record surface electromyography of human brachioradialis and monitor electrocorticography signals of a rat in normal and epileptic states. The developed strategy shows the potential to provide a new perspective for the fabrication of flexible electronics.
| S-EPMC9676391 | biostudies-literature
Project description:Embedding liquid metals (LMs) into an elastomer is emerging as a promising strategy for stretchable conductors. Existing manufacturing techniques are struggling between spatial resolution and process complexity and are limited to chemically resistant substrates. Here, we report on a hybrid process combining stencil lithography and centrifugal force-assisted patterning of liquid metal for the development of LM-based stretchable conductors. The selective wetting behavior of oxide-removed eutectic gallium-indium (EGaIn) on metal patterns defined by stencil lithography enables micrometer scale LM patterns on an elastomeric substrate. Stencil lithography allows for defining metal regions without harsh chemical treatments, making it suitable for a wide range of substrates. Microscale LM patterns are achieved by efficiently removing the excess material by the centrifugal forces experienced from spinning the substrate. The proposed approach allows for the creation of LM patterns with a line width as small as 2 μm on a stretchable poly(dimethylsiloxane) (PDMS) substrate. The electrical measurement results show that the fabricated EGaIn devices can endure 40% mechanical strain over several thousands of cycles. Furthermore, a stencil design using microbridges is proposed to address the mechanical stability issue in stencil lithography. An EGaIn conductor with a serpentine structure and an interdigitated capacitor are fabricated and characterized. The results demonstrate that the patterned serpentine conductors retain their functionality with applied mechanical strain up to 80%. The performance of the interdigitated capacitors upon applied strain is in good agreement with the theoretical estimation. Finally, we demonstrate our approach also on poly(octamethylene maleate (anhydride) citrate) (POMaC) substrates to broaden the use of the proposed method to not only flexible and stretchable but also biodegradable substrates, opening a way for in vivo transient microsystem engineering. The work presented here provides a versatile and reliable approach for manufacturing stretchable conductors.
| S-EPMC8717634 | biostudies-literature
Project description:Encapsulation of electronic devices such as dye-sensitized solar cells (DSSCs) is prone to degradation under normal atmospheric conditions, even with hermetic barriers on the metal electrodes. Overcoming this problem is crucial to increasing DSSC lifetimes and making them commercially viable. Herein, we report a new impermeable flexible liquid barrier film using polyvinyl alcohol (PVA) and partially reduced graphene oxide (PrGO), which dramatically enhances the lifetime of Ag metal electrodes (typically used in DSSCs) immersed in a highly acidic iodolyte solution. The Ag metal electrode encapsulated by the PVA/PrGO film survived for over 500 hrs, superior to existing barriers of glass frits, epoxy resins and polymers. The PVA/PrGO film strongly adheres to the Ag metal surface, and the resulting PVA/PrGO/Ag electrode is stable even on a curved substrate, with a sheet resistance nearly independent of curvature. These results give new insight for the design of high-performance and solution-processable flexible liquid barrier films for a wide range of applications, in particular for the encapsulation of electronic devices with liquid electrolytes.
| S-EPMC4893703 | biostudies-literature
Project description:Stretchable, biocompatible devices can bridge electronics and biology. However, most stretchable conductors for such devices are toxic, costly, and regularly break/degrade after several large deformations. Here we show printable, highly stretchable, and biocompatible metal-polymer conductors by casting and peeling off polymers from patterned liquid metal particles, forming surface-embedded metal in polymeric hosts. Our printable conductors present good stretchability (2,316 S/cm at a strain of 500%) and repeatability (ΔR/R <3% after 10,000 cycles), which can satisfy most electrical applications in extreme deformations. This strategy not only overcomes large surface tension of liquid metal but also avoids the undesirable sintering of its particles by stress in deformations, such that stretchable conductors can form on various substrates with high resolution (15 μm), high throughput (∼2,000 samples/hour), and low cost (one-quarter price of silver). We use these conductors for stretchable circuits, motion sensors, wearable glove keyboards, and electroporation of live cells.
| S-EPMC6146547 | biostudies-literature
Project description:As the regenerative mechanisms of biological organisms, self-healing provides useful functions for soft electronics or associated systems. However, there have been few examples of soft electronics where all components have self-healing properties while also ensuring compatibility between components to achieve multifunctional and resilient bio-integrated electronics. Here, we introduce a stretchable, biodegradable, self-healing conductor constructed by combination of two layers: (i) synthetic self-healing elastomer and (ii) self-healing conductive composite with additives. Abundant dynamic disulfide and hydrogen bonds of the elastomer and conductive composite enable rapid and complete recovery of electrical conductivity (~1000 siemens per centimeter) and stretchability (~500%) in response to repetitive damages, and chemical interactions of interpenetrated polymer chains of these components facilitate robust adhesion strength, even under extreme mechanical stress. System-level demonstration of soft, self-healing electronics with diagnostic/therapeutic functions for the urinary bladder validates the possibility for versatile, practical uses in biomedical research areas.
| S-EPMC11373598 | biostudies-literature
Project description:Magnetic resonance imaging systems rely on signal detection via radiofrequency coil arrays which, ideally, need to provide both bendability and form-fitting stretchability to conform to the imaging volume. However, most commercial coils are rigid and of fixed size with a substantial mean offset distance of the coil from the anatomy, which compromises the spatial resolution and diagnostic image quality as well as patient comfort. Here, we propose a soft and stretchable receive coil concept based on liquid metal and ultra-stretchable polymer that conforms closely to a desired anatomy. Moreover, its smart geometry provides a self-tuning mechanism to maintain a stable resonance frequency over a wide range of elongation levels. Theoretical analysis and numerical simulations were experimentally confirmed and demonstrated that the proposed coil withstood the unwanted frequency detuning typically observed with other stretchable coils (0.4% for the proposed coil as compared to 4% for a comparable control coil). Moreover, the signal-to-noise ratio of the proposed coil increased by more than 60% as compared to a typical, rigid, commercial coil.
| S-EPMC8355233 | biostudies-literature
Project description:Soft stretchable sensors rely on polymers that not only withstand large deformations while retaining functionality but also allow for ease of application to couple with the body to capture subtle physiological signals. They have been applied towards motion detection and healthcare monitoring and can be integrated into multifunctional sensing platforms for enhanced human machine interface. Most advances in sensor development, however, have been aimed towards active materials where nearly all approaches rely on a silicone-based substrate for mechanical stability and stretchability. While silicone use has been advantageous in academic settings, conventional silicones cannot offer self-healing capability and can suffer from manufacturing limitations. This review aims to cover recent advances made in polymer materials for soft stretchable conductors. New developments in substrate materials that are compliant and stretchable but also contain self-healing properties and self-adhesive capabilities are desirable for the mechanical improvement of stretchable electronics. We focus on materials for stretchable conductors and explore how mechanical deformation impacts their performance, summarizing active and substrate materials, sensor performance criteria, and applications.
| S-EPMC7408380 | biostudies-literature
Project description:Considering the various applications of wearable and bio-implantable devices, it is desirable to realize stretchable acoustic devices for body-attached applications such as sensing biological signals, hearing aids, and notification of information via sound. In this study, we demonstrate the facile fabrication of a Stretchable Acoustic Device (SAD) using liquid metal coil of Galinstan where the SAD is operated by the electromagnetic interaction between the liquid metal coil and a Neodymium (Nd) magnet. To fabricate a liquid metal coil, Galinstan was injected into a micro-patterned elastomer channel. This fabricated SAD was operated simultaneously as a loudspeaker and a microphone. Measurements of the frequency response confirmed that the SAD was mechanically stable under both 50% uniaxial and 30% biaxial strains. Furthermore, 2000 repetitive applications of a 50% uniaxial strain did not induce any noticeable degradation of the sound pressure. Both voice and the beeping sound of an alarm clock were successfully recorded and played back through our SAD while it was attached to the wrist under repeated deformation. These results demonstrate the high potential of the fabricated SAD using Galinstan voice coil in various research fields including stretchable, wearable, and bio-implantable acoustic devices.
| S-EPMC4504143 | biostudies-literature
Project description:Flexible and stretchable electronics require both sensing elements and stretching-insensitive electrical connections. Conductive polymer composites and liquid metals are highly deformable but change their conductivity upon elongation and/or contain rare metals. Solid conductive composites are limited in mechanoelectrical properties and are often combined with macroscopic Kirigami structures, but their use is limited by geometrical restraints. Here, we introduce "Electrofluids", concentrated conductive particle suspensions with transient particle contacts that flow under shear that bridge the gap between classic solid composites and liquid metals. We show how Carbon Black (CB) forms large agglomerates when using incompatible solvents that reduce the electrical percolation threshold by 1 order of magnitude compared to more compatible solvents, where CB is well-dispersed. We analyze the correlation between stiffness and electrical conductivity to create a figure of merit of first electrofluids. Sealed elastomeric tubes containing different types of electrofluids were characterized under uniaxial tensile strain, and their electrical resistance was monitored. We found a dependency of the piezoresistivity with the solvent compatibility. Electrofluids enable the rational design of sustainable soft electronics components by simple solvent choice and can be used both as sensor and electrode materials, as we demonstrate.
| S-EPMC11345724 | biostudies-literature
Project description:Flexible implantable medical devices (IMDs) are an emerging technology that may substantially improve the disease treatment efficacy and quality of life of patients. While many advancements have been achieved in IMDs, the constantly straining application conditions impose extra requirements for the packaging material, which needs to retain both high stretchability and high water resistivity under dynamic strains in a physiological environment. This work reports a polyisobutylene (PIB) blend-based elastomer that simultaneously offers a tissue-like elastic modulus and excellent water resistivity under dynamic strains. The PIB blend is a homogeneous mixture of two types of PIB molecules with distinct molecular weights. The blend achieved an optimal Young's modulus of 62 kPa, matching those of soft biological tissues. The PIB blend film also exhibited an extremely low water permittivity of 1.6-2.9 g m-2 day-1, from unstrained to 50% strain states. The combination of high flexibility and dynamic water resistivity was tested using triboelectric nanogenerators (TENGs). The PIB blend-packaged TENG was able to stably operate in water for 2 weeks, substantially surpassing the protection offered by Ecoflex. This work offered a promising material solution for packaging flexible IMDs to achieve stable performance in a strained physiological environment.
| S-EPMC10018529 | biostudies-literature