Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

A Cantilever Beam-Based Triboelectric Nanogenerator as a Drill Pipe Transverse Vibration Energy Harvester Powering Intelligent Exploitation System

ABSTRACT: Measurement While Drilling (MWD) is the most commonly used real-time information acquisition technique in offshore intelligent drilling, its power supply has always been a concern. Triboelectric nanogenerators have been shown to harvest low-frequency vibrational energy in the environment and convert it into electricity to power small sensors and electrical devices. This work proposed a cantilever-beam-based triboelectric nanogenerator (CB-TENG) for transverse vibration energy harvesting of a drill pipe. The CB-TENG consists of two vibrators composed of spring steel with PTFE attached and Al electrodes. The structurally optimized CB-TENG can output a peak power of 2.56 mW under the vibration condition of f = 3.0 Hz and A = 50 mm, and the electrical output can be further enhanced with the increased vibration parameters. An array-type vibration energy harvester integrated with eight CB-TENGs is designed to fully adapt to the interior of the drill pipe and improve output performance. The device can realize omnidirectional vibration energy harvesting in the two-dimensional plane with good robustness. Under the typical vibration condition, the short-circuit current and the peak power can reach 49.85 μA and 30.95 mW, respectively. Finally, a series of demonstration experiments have been carried out, indicating the application prospects of the device.

SUBMITTER: Lian Z

PROVIDER: S-EPMC9185564 | biostudies-literature | 2022 Jun

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Ultrasound-mediated triboelectric nanogenerator for powering on-demand transient electronics.

Project description:On-demand transient electronics, technologies referring subsequent material disintegration under well-defined triggering events and programmed time lines, offer exceptional clinical experiences in diagnosis, treatment, and rehabilitation. Despite potential benefits, such as the elimination of surgical device removal and reduction of long-term inimical effects, their use is limited by the nontransient conventional power supplies. Here, we report an ultrasound-mediated transient triboelectric nanogenerator (TENG) where ultrasound determines energy generation and degradation period. Our findings on finite element method simulation show that porous structures of the poly(3-hydroxybutyrate-co-3-hydroxyvalerate) play an essential role in the triggering transient process of our device under high-intensity ultrasound. Besides, the addition of polyethylene glycol improves triboelectric output performance; the voltage output increased by 58.5%, from 2.625 to 4.160 V. We successfully demonstrate the tunable transient performances by ex vivo experiment using a porcine tissue. This study provides insight into practical use of implantable TENGs based on ultrasound-triggered transient material design.

| S-EPMC8741185 | biostudies-literature

Dual-Mode Coupled Triboelectric Nanogenerator for Harvesting Random Vibration Energy.

Project description:As a new energy harvesting technology, triboelectric nanogenerators are widely used for vibration mechanical energy harvesting. However, the current schemes ignore the composite characteristics of vibration, with problems such as utilization and low collection efficiency. In this paper, a random resonance cantilever beam triboelectric nanogenerator (RCB-TENG) with dual-mode coupled is presented, the working mode is a coupling form of in-plane sliding and vertical contact-separation that can effectively collect complex vibration energy in transverse and longitudinal directions. The influences of the structural parameters of the RCB-TENG and different dielectric materials on the output performance are systematically investigated. The single vibration module achieved a power density of 463.56 mW/m2 and a transfer charge of 10.7 μC at a vibration frequency of 46 Hz, an increase in power density, and a transfer charge of 4.94 and 3.82 times, respectively, compared to the conventional contact-separation mode. Finally, the RCB-TENG was tested in practice, and it was observed that nine 1 W commercial LED bulbs and 500 5 mm diameter LED lamps were successfully lit. This work offers new ideas for distributed energy harvesting technologies and holds broad promise in the field of energy harvesting from wind, water, wave, and random vibrations caused by mechanical energy.

| S-EPMC9893744 | biostudies-literature

A Contact-Mode Triboelectric Nanogenerator for Energy Harvesting from Marine Pipe Vibrations.

Project description:Structural health monitoring is of great significance to ensure the safety of marine pipes, while powering the required monitoring sensors remains a problem because the ocean environment is not amenable to the traditional ways of providing an external power supply. However, mechanical energy due to the vortex-induced vibration of pipelines may be harvested to power those sensors, which is a convenient, economic and environmentally friendly way. We here exploit a contact-separation mode triboelectric nanogenerator (TENG) to create an efficient energy harvester to transform the mechanical energy of vibrating pipes into electrical energy. The TENG device is composed of a tribo-pair of dielectric material films that is connected to a mass-spring base to guarantee the contact-separation motions of the tribo-pair. Experimental tests are conducted to demonstrate the output performance and long-term durability of the TENG device by attaching it to a sample pipe. A theoretical model for the energy harvesting system is developed for predicting the electrical output performance of the device. It is established that the normalized output power depends only on two compound variables with all typical factors taken into consideration simultaneously. The simple scale law is useful to reveal the underlying mechanism of the device and can guideline the optimization of the device based on multi-parameters analyses. The results here may provide references for designing contact-mode TENG energy harvesting devices based on the vibration of marine pipes and similar structures.

| S-EPMC7926989 | biostudies-literature

A Portable Triboelectric Nanogenerator Based on Dehydrated Nopal Powder for Powering Electronic Devices.

Project description:Triboelectric nanogenerators (TENGs) based on organic materials can harvest green energy to convert it into electrical energy. These nanogenerators could be used for Internet-of-Things (IoT) devices, substituting solid-state chemical batteries that have toxic materials and limited-service time. Herein, we develop a portable triboelectric nanogenerator based on dehydrated nopal powder (NOP-TENG) as novel triboelectric material. In addition, this nanogenerator uses a polyimide film tape adhered to two copper-coated Bakelite plates. The NOP-TENG generates a power density of 2309.98 μW·m-2 with a load resistance of 76.89 MΩ by applying a hand force on its outer surface. Furthermore, the nanogenerator shows a power density of 556.72 μW·m-2 with a load resistance of 76.89 MΩ and under 4g acceleration at 15 Hz. The output voltage of the NOP-TENG depicts a stable output performance even after 27,000 operation cycles. This nanogenerator can light eighteen green commercial LEDs and power a digital calculator. The proposed NOP-TENG has a simple structure, easy manufacturing process, stable electric behavior, and cost-effective output performance. This portable nanogenerator may power electronic devices using different vibration energy sources.

| S-EPMC10180813 | biostudies-literature

A flexible and biocompatible triboelectric nanogenerator with tunable internal resistance for powering wearable devices.

Project description:Recently, triboelectric energy nanogenerators (TENGs) have been paid the most attention by many researchers to convert mechanical energy into electrical energy. TENGs usually have a simple structure and a high output voltage. However, their high internal resistance results in low output power. In this work, we propose a flexible triboelectric energy nanogenerator with the double-side tribological layers of polydimethlysiloxane (PDMS) and PDMS/multiwall carbon nanotube (MWCNT). MWCNTs with different concentrations have been doped into PDMS to tune the internal resistance of triboelectric nanogenerator and optimize its output power. The dimension of the fabricated prototype is ~3.6 cm(3). Three-axial force sensor is used to monitor the applied vertical forces on the device under vertical contact-separation working mode. The Prototype with 10 wt% MWCNT (Prototype I) produces higher output voltage than one with 2 wt% MWCNT (Prototype II) due to its higher dielectric parameter measured by LRC impedance analyzer. The triboelectric output voltages of Prototype I and Prototype II are 30 V and 25 V under the vertical force of 3.0 N, respectively. Their maximum triboelectric output powers are ~130 μW at 6 MΩ and ~120 μW at 8.6 MΩ under vertical forces, respectively.

| S-EPMC4768091 | biostudies-literature

Theoretical and Experimental Studies on MEMS Variable Cross-Section Cantilever Beam Based Piezoelectric Vibration Energy Harvester.

Project description:The piezoelectric vibration energy harvester (PVEH) based on the variable cross-section cantilever beam (VCSCB) structure has the advantages of uniform axial strain distribution and high output power density, so it has become a research hotspot of the PVEH. However, its electromechanical model needs to be further studied. In this paper, the bidirectional coupled distributed parameter electromechanical model of the MEMS VCSCB based PVEH is constructed, analytically solved, and verified, which laid an important theoretical foundation for structural design and optimization, performance improvement, and output prediction of the PVEH. Based on the constructed model, the output performances of five kinds of VCSCB based PVEHs with different cross-sectional shapes were compared and analyzed. The results show that the PVEH with the concave quadratic beam shape has the best output due to the uniform surface stress distribution. Additionally, the influence of the main structural parameters of the MEMS trapezoidal cantilever beam (TCB) based PVEH on the output performance of the device is theoretically analyzed. Finally, a prototype of the Aluminum Nitride (AlN) TCB based PVEH is designed and developed. The peak open-circuit voltage and normalized power density of the device can reach 5.64 V and 742 μW/cm3/g2, which is in good agreement with the theoretical model value. The prototype has wide application prospects in the power supply of the wireless sensor network node such as the structural health monitoring system and the Internet of Things.

| S-EPMC8304101 | biostudies-literature

A cantilever-structure triboelectric nanogenerator for energy harvesting and defect detection via long short-term memory network.

Project description:The electric signals of cantilever energy harvesting devices with/without a crack were mainly obtained by external sensors, so detecting device damage on a large scale is difficult. To tackle the issue, a cantilever-structure freestanding triboelectric nanogenerator (CSF-TENG) device was proposed, which can scavenge ambient energy and act as a self-powered sensor. Firstly, the relation between the peak-to-peak voltage and amplitude of the CSF-TENG was established. Next, the output performance of the CSF-TENG was measured. Then, depending on electric signals output by the CSF-TENG, a cantilever defect identification model was built by using the wavelet packet and long short-term memory (LSTM) algorithms. The experimental results manifest that the accuracy of the model is about 98.6%. Thus, the CSF-TENG with a crack can be detected timely due to its self-monitoring ability, which is of great significance for the development of self-powered sensor networks.

| S-EPMC9730220 | biostudies-literature

A Forest-Based Triboelectric Energy Harvester.

Project description:Triboelectric nanogenerators (TENGs) are a new class of energy harvesting devices that have the potential to become a dominating technology for producing renewable energy. The versatility of their designs allows TENGs to harvest mechanical energy from sources like wind and water. Currently used renewable energy technologies have a restricted number of materials from which they can be constructed, such as metals, plastics, semiconductors, and rare-earth metals. These materials are all non-renewable in themselves as they require mining/drilling and are difficult to recycle at end of life. TENGs on the other hand can be built from a large repertoire of materials, including materials from bio-based sources. Here, a TENG constructed fully from wood-derived materials like lignin, cellulose, paper, and cardboard, thus making it 100% green, recyclable, and even biodegradable, is demonstrated. The device can produce a maximum voltage, current, and power of 232 V, 17 mA m-2, and 1.6 W m-2, respectively, which is enough to power electronic systems and charge 6.5 µF capacitors. Finally, the device is used in a smart package application as a self-powered impact sensor. The work shows the feasibility of producing renewable energy technologies that are sustainable both with respect to their energy sources and their material composition.

| S-EPMC9581787 | biostudies-literature

Integrated charge excitation triboelectric nanogenerator.

Project description:Performance of triboelectric nanogenerators is limited by low and unstable charge density on tribo-layers. An external-charge pumping method was recently developed and presents a promising and efficient strategy towards high-output triboelectric nanogenerators. However, integratibility and charge accumulation efficiency of the system is rather low. Inspired by the historical development of electromagnetic generators, here, we propose and realize a self-charge excitation triboelectric nanogenerator system towards high and stable output in analogy to the principle of traditional magnetic excitation generators. By rational design of the voltage-multiplying circuits, the completed external and self-charge excitation modes with stable and tailorable output over 1.25 mC m-2 in contact-separation mode have been realized in ambient condition. The realization of the charge excitation system in this work may provide a promising strategy for achieving high-output triboelectric nanogenerators towards practical applications.

| S-EPMC6440990 | biostudies-literature

A Robust Silicone Rubber Strip-Based Triboelectric Nanogenerator for Vibration Energy Harvesting and Multi-Functional Self-Powered Sensing.

Project description:Vibration is a common phenomenon in various fields which can not only indicate the working condition of the installation, but also serve as an energy source if it is efficiently harvested. In this work, a robust silicone rubber strip-based triboelectric nanogenerator (SRS-TENG) for vibration energy harvesting and multi-functional self-powered sensing is proposed and systematically investigated. The SRS-TENG consists of a silicone rubber strip and two aluminum electrode layers supported by polylactic acid (PLA), and acts as a sustainable power source and vibration frequency, amplitude and acceleration sensor as well. The soft contact between the aluminum electrode and silicone rubber strip makes it robust and stable even after 14 days. It can be applied in ranges of vibration frequencies from 5 to 90 Hz, and amplitudes from 0.5 to 9 mm, which shows it has advantages in broadband vibration. Additionally, it can achieve lower startup limits due to its soft structure and being able to work in multi-mode. The output power density of the SRS-TENG can reach 94.95 W/m3, matching a resistance of 250 MΩ, and it can light up more than 100 LEDs and power a commercial temperature sensor after charging capacitors. In addition, the vibration amplitude can be successfully detected and displayed on a human-machine interface. Moreover, the frequency beyond a specific limit can be distinguished by the SRS-TENG as well. Therefore, the SRS-TENG can be utilized as an in situ power source for distributed sensor nodes and a multifunctional self-powered vibration sensor in many scenarios.

| S-EPMC9030836 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data