Combined Activated Carbon with Spent Fluid Catalytic Cracking Catalyst and MgO for the Catalytic Conversion of Waste Polyethylene Wax into Diesel-like Hydrocarbon Fuels
Ontology highlight
ABSTRACT:
SUBMITTER: Kasetsupsin P
PROVIDER: S-EPMC9202014 | biostudies-literature | 2022 May
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:This work provided catalytic copyrolysis of spent lubricating oil (SLO) with waste low-density polyethylene (LDPE) using copper modification of a spent fluid catalytic cracking (sFCC) catalyst to produce diesel-like fuels in a microbatch reactor, which will lead to effective waste management, ensure sustainability, and serve as an alternative energy source. The effects of LDPE blended with SLO, temperature, reaction time, and catalyst loading using an inert nitrogen atmosphere were investigated on the yields and distributions of copyrolyzed oil, while metal modification of the sFCC was prepared and used to investigate the catalytic activity. The temperature and time of reaction played an important role in the gaseous contribution to the pyrolysis of SLO. The addition of the LDPE ratio in the catalytic copyrolysis, including Cu loading on a spent FCC template, also enhanced the acidity and was responsible for the catalytic activity, which could improve the product distribution and chemical compounds in a range of diesel-like fuels. It was shown that the pyrolyzed oil was in the range of C7-C26 with a maximum diesel-like fraction of 23.11 ± 2.88 wt % compared with the catalytic pyrolysis of SLO alone, which contained a diesel-like fraction of only 12.45 ± 1.92 wt %. It was noticed that the acid active site of the catalyst resulted in a carbon-carbon bond cleavage and further secondary reaction, leading to the conversion of the long residue fraction into a light oil product. In addition, the LDPE ratio in the catalytic copyrolysis could improve the product distribution and chemical compounds in a range of diesel-like compounds, as confirmed by the GC/MS analysis. Catalytic copyrolysis oil of the optimal process condition (0.7:0.3 mass molar of SLO/LDPE, 450 °C, 60 min, 3 wt % Cu-sFCC, and 10 wt % catalyst loading) mainly contains light hydrocarbons in the C7-C19 range. Accordingly, both the product selectivity and the conversion of the long residue to the diesel-like fraction were nearly stable (59.01 ± 1.36%) during the catalyst reusability test from one to three cycles without regeneration and significantly decreased after the fifth cycle. This is an indication that the copyrolysis enhanced the conversion of SLO by LPDE blended into smaller hydrocarbon compounds, and the catalytic activity therefore showed a major tendency toward the formation of diesel-like fractions (C8-C18).
| S-EPMC10620889 | biostudies-literature
Project description:The disposal of waste rubber and scrap tyres is a significant issue globally; disposal into stockpiles and landfill poses a serious threat to the environment, in addition to creating ecological problems. Fuel production from tyre waste could form part of the solution to this global issue. Therefore, this paper studies the potential of fuels derived from waste tyres as alternatives to diesel. Production methods and the influence of reactor operating parameters (such as reactor temperature and catalyst type) on oil yield are outlined. These have a major effect on the performance and emission characteristics of diesel engines when using tyre derived fuels. In general, tyre derived fuels increase the brake specific fuel consumption and decrease the brake thermal efficiency. The majority of studies indicate that NOx emissions increase with waste tyre derived fuels; however, a few studies have reported the opposite trend. A similar increasing trend has been observed for CO and CO2 emissions. Although most studies reported an increase in HC emission owing to lower cetane number and higher density, some studies have reported reduced HC emissions. It has been found that the higher aromatic content in such fuels can lead to increased particulate matter emissions.
| S-EPMC5802751 | biostudies-literature
Project description:Bioleaching uses biodegradable organic acids, thereby making the process environmental friendly as compared to chemical leaching. In this work, bioleaching of aluminium (Al) metal from spent catalyst was investigated by using three Aspergillus strains (A. niger, A. foetidus, and A. carbonarius). Bioleaching was performed in batch culture mode at different loading densities of spent catalyst (i.e., 0.4%, 0.8% and 1.2% (w/v)). The highest Al leaching efficiency of 88.43% was obtained at 0.8% ((w/v)) catalyst loading using A. foetidus, further increase in the catalyst loading decreased the efficiency. In addition to this, molasses was used as a carbon source (low-cost) at various concentrations for bioleaching of spent catalyst and the results were found to be significant at 40 g/L sugar concertation with 60% bioleaching efficiency. Overall, this study indicates that A. foetidus have the potential for leaching of Al from spent catalysts. Therefore, present research findings suggested that, instead of using mineral acids, organic acids (biodegradable) usage for metal leaching process is highly reliable and eco-friendly as well.
| S-EPMC6551381 | biostudies-literature
Project description:Herein, the pyrolysis of low-density polyethylene (LDPE) scrap in the presence of a H-ZSM-11 zeolite was conducted as an effort to valorize plastic waste to fuel-range chemicals. The LDPE-derived pyrolytic gas was composed of low-molecular-weight aliphatic hydrocarbons (e.g., methane, ethane, propane, ethylene, and propylene) and hydrogen. An increase in pyrolysis temperature led to increasing the gaseous hydrocarbon yields for the pyrolysis of LDPE. Using the H-ZSM-11 catalyst in the pyrolysis of LDPE greatly enhanced the content of propylene in the pyrolytic gas because of promoted dehydrogenation of propane formed during the pyrolysis. Apart from the light aliphatic hydrocarbons, jet fuel-, diesel-, and motor oil-range hydrocarbons were found in the pyrolytic liquid for the non-catalytic and catalytic pyrolysis. The change in pyrolysis temperature for the catalytic pyrolysis affected the hydrocarbon compositions of the pyrolytic liquid more materially than for the non-catalytic pyrolysis. This study experimentally showed that H-ZSM-11 can be effective at producing fuel-range hydrocarbons from LDPE waste through pyrolysis. The results would contribute to the development of waste valorization process via plastic upcycling.
| S-EPMC8068035 | biostudies-literature
Project description: Not available
| S-EPMC11541447 | biostudies-literature
Project description:Waste plastics bring about increasingly serious environmental challenges, which can be partly addressed by their interconversion into valuable compounds. It is hypothesized that the porosity and acidity of a zeolite-based catalyst will affect the selectivity and effectiveness, enabling a controllable and selective conversion of polyethylene (PE) into gas-diesel or lubricating base oil. A series of embryonic, partial- and well-crystalline zeolites beta with adjustable porosity and acidity are prepared from mesoporous SBA-15. The catalysts and catalytic systems are studied with nuclear magnetic resonance (NMR), X-ray diffraction (XRD), and adsorption kinetics and catalytic reactions. The adjustable porosity and acidity of zeolite-beta-based catalysts achieve a controllable selectivity toward gas-diesel or lubricating base oil for PE cracking. With a catalyst with mesopores and appropriate acid sites, a fast escape and reduced production of cracking of intermediates are observed, leading to a significant fraction (88.7%) of lubricating base oil. With more micropores, a high acid density, and strong acid strength, PE is multiply cracked into low carbon number hydrocarbons. The strong acid center of the zeolite is confirmed to facilitate significantly the activation of hydrogen (H2), and, an in situ ammonia poisoning strategy can significantly inhibit hydrogen transfer and effectively regulate the product distribution.
| S-EPMC11425912 | biostudies-literature
Project description:Catalytic pyrolysis of waste plastics using low cost binder-free pelletized bentonite clay has been investigated to yield pyrolysis oils as drop-in replacements for commercial liquid fuels such as diesel and gasohol 91. Pyrolysis of four waste plastics, polystyrene, polypropylene, low density polyethylene and high density polyethylene, was achieved at a bench scale (1 kg per batch) to produce useful fuel products. Importantly, the addition of binder-free bentonite clay pellets successfully yielded liquid based fuels with increased calorific values and lower viscosity for all plastic wastes. This larger scale pyrolysis study demonstrated that use of a catalyst in powder form can lead to significant pressure drops in the catalyst column, thus slowing the process (more than 1 hour). Importantly, the use of catalyst pellets eliminated the pressure drop and reduced pyrolysis processing time to only 10 minutes for 1 kg of plastic waste. The pyrolysis oil composition from polystyrene consists of 95% aromatic hydrocarbons, while in contrast, those from polypropylene, low density polyethylene and high density polyethylene, were dominated by aliphatic hydrocarbons, as confirmed by GC-MS. FTIR analysis demonstrated that low density polyethylene and high density polyethylene oils had functional groups that were consistent with those of commercial diesel (96% similarity match). In contrast, pyrolysis-oils from polystyrene demonstrated chemical and physical properties similar to those of gasohol 91. In both cases no wax formation was observed when using the bentonite clay pellets as a catalyst in the pyrolysis process, which was attributed to the high acidity of the bentonite catalyst (low SiO2 : Al2O3 ratio), thus making it more active in cracking waxes compared to the less acidic heterogeneous catalysts reported in the literature. Pyrolysis-oil from the catalytic treatment of polystyrene resulted in greater engine power, comparable engine temperature, and lower carbon monoxide (CO) and carbon dioxide (CO2) emissions, as compared to those of uncatalysed oils and commercial fuel in a gasoline engine. Pyrolysis-oils from all other polymers demonstrated comparable performance to diesel in engine power tests. The application of inexpensive and widely available bentonite clay in pyrolysis could significantly aid in repurposing plastic wastes.
| S-EPMC9060870 | biostudies-literature
Project description:Pyrolysis techniques provide an interesting way of recycling plastic wastes (PW) by transforming them into liquid fuels with high calorific values. Catalysts are employed in PW pyrolysis in order to favor cracking reactions; in that regard, cheap and abundant natural resources are being investigated as potential catalyst precursors. This article explores the pyrolysis of low-density polyethylene (LDPE) in a semibatch reactor under a reduced pressure of 300 torr and temperatures in the range of 370 °C-430 °C. Three different solid materials, an activated carbon (AC1), a commercial Fluid cracking catalyst (FCC) and an aluminum- pillared clay (Al-PILC), were tested as catalysts for the pyrolysis process. Thermogravimetric analyzes were previously performed to select the most catalytically active materials. AC1 displayed very low catalytic activity while FCC and Al-PILC displayed high activity and conversion to liquid products. Hydrocarbons ranging from C5 to C28 were identified in the liquid products as well as significant changes in their composition when FCC and Al-PILC catalyst were used. Differences in the catalytic activity of the 3 solid materials are ascribed mainly to differences in their acid properties.
| S-EPMC7527577 | biostudies-literature
Project description:Cracking of plastic waste by the acidic FAU-type zeolites faces challenges of low production of light olefins, a high amount of coke formation, and expensive process. Basic zeolites might be a better alternative; however, their preparation is difficult and the related cracking mechanism is unknown. We addressed these difficulties by direct synthesis of a hierarchical acidic-basic FAU-type zeolite (HY-BS) using silica extracted from a low-grade kaolin containing alkaline (earth) metals and investigated the impact of basicity in the linear low density polyethylene (LLDPE) cracking mechanism and products distribution. Compared to an acidic HY zeolite, the HY-BS presented comparable density of Brønsted acidity but a drastically higher density of the basicity. The HY-BS had comparable activity to the reference HY zeolite, but it produced twice light olefins (30.5 vs. 16.2%), triple lighter aromatics (41.0 vs. 13.8%), and less coke in LLDPE cracking. The thermodynamic investigation of thermal and zeolitic cracking of LLDPE was conducted based on the TGA results, along with kinetic analysis using four model-free techniques and a differential method. According to kinetic and thermodynamic parameters and product distribution, the HY-BS exhibited a dual cracking pathway that first followed a carbocation mechanism before switching to a radical mechanism as the reaction progressed, accounting for the reason behind improved light olefins selectivity. Consequently, direct promotion of the basicity of the zeolites synthesized from impure kaolin was effective to overcome difficulties facing plastic waste cracking.
| S-EPMC11822766 | biostudies-literature
Project description:Refiners around the globe are either considering or are actively replacing a portion of their crude oil inputs originating from fossil sources with alternative sources, including recycled materials (plastics, urban waste, mixed solid waste) and renewable materials (bio-mass waste, vegetable oils). In this paper, we explore such replacement, specifically focusing on the fluid catalytic cracking (FCC) operation. Five pyrolysis oils, obtained from municipal solid waste (MSW) and biogenic material (olive stones/pits), were fully characterized and tested at 10% loading against a standard fluid catalytic cracking (FCC) vacuum gasoil (VGO) feed in a bench scale reactor using an industrially available fluid catalytic cracking catalyst based on ultrastable Y zeolite to simulate fluid catalytic cracking co-processing. Despite having unique feed properties, including high Conradson carbon (e.g., up to 19.41 wt%), water (e.g., up to 5.7 wt%), and contaminants (e.g., up to 227 ppm Cl) in some cases, the five pyrolysis oils gave similar yield patterns as vacuum gasoil. Gasoline was slightly (ca. 1 wt%) higher in all cases and LPG slightly (ca. 1 wt%) lower. Olefinicity in the LPG streams were unchanged, bottoms and light cycle oil (LCO) showed no significant changes, while dry gas was slightly (up to -0.2 wt%) lower. Coke selectivity was also unchanged (maximum -7.7 wt%, relatively), suggesting minimal to no heat balance concerns when co-processing in an industrial fluid catalytic cracking unit. The results demonstrate the applicability of municipal solid waste and biogenic originating pyrolysis oils into a refinery. A catalyst design concept is explored, based on higher rare Earth oxide exchange and/or utilization of ZSM-5 zeolite, that would further minimize the impacts of replacing fossil oils with pyrolysis oils, namely one that shifts the 1% higher gasoline into LPG.
| S-EPMC9893771 | biostudies-literature