Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Glycothermal synthesis and photoluminescence of Mg-Si modified Ce:YAG nanophosphors.

ABSTRACT: The absorption spectrum of Ce in a YAG based host grown using the glycothermal method was modified using the addition of Mg-Si pairs. Photoluminescence intensity was dramatically improved by increasing the reaction temperature to 315 °C instead of the conventionally used 300 °C. It was found that Mg acetate and tetraethylorthosilicate (TEOS) are suitable as precursors for the glycothermal process, as EDS elemental mapping showed their homogeneous inclusion in the final product. Their addition only slightly modified the emission spectrum of Ce:YAG. It was found that increasing the reaction temperature to 315 °C yielded nanoparticles 56 ± 16 nm in size with a 3.3× enhancement in absorption and 3.7× enhancement in emission intensities compared to samples synthesized at 300 °C, and an increase in photoluminescence quantum yield from 32% to 48%. Reaction kinetics of the precursors and a proposed route for post-synthesis surface functionalization are discussed.

SUBMITTER: Peter S

PROVIDER: S-EPMC9417575 | biostudies-literature | 2021 May

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Publications

Glycothermal synthesis and photoluminescence of Mg-Si modified Ce:YAG nanophosphors.

Peter Samuel S Fitzpatrick Maureen M Kitai Adrian A

Nanoscale advances 20210331 10

The absorption spectrum of Ce in a YAG based host grown using the glycothermal method was modified using the addition of Mg-Si pairs. Photoluminescence intensity was dramatically improved by increasing the reaction temperature to 315 °C instead of the conventionally used 300 °C. It was found that Mg acetate and tetraethylorthosilicate (TEOS) are suitable as precursors for the glycothermal process, as EDS elemental mapping showed their homogeneous inclusion in the final product. Their addition on ...[more]

PMID: 36134185

Similar Datasets

Spherical submicron YAG:Ce particles with controllable particle outer diameters and crystallite sizes and their photoluminescence properties.

Project description:The purpose of this study was to demonstrate the preparation of spherical submicron YAG:Ce particles with controllable particle outer diameters and crystallite sizes and their photoluminescence (PL) properties, which were produced using a flame-assisted spray-pyrolysis method followed by the annealing process. The correlation of particle outer diameter, crystallite size, and PL performance of the prepared particles was also investigated. Experimental results showed that the increases in the particle outer diameters have an impact on the obtainment of higher PL performance. Large particle outer diameters permitted the crystallites to grow more, whereas this is in contrast to the condition for small particle outer diameter having limitations in crystallite growth. This study also found that too large outer diameter (>557 nm) was not effective since crystallites cannot grow anymore and it permits possible scattering problems. This study provides significant information for optimizing synthesis parameters for controlling particle outer diameters and crystallite sizes, which could be relevant to other functional properties, especially for lens, solar cell, and LED applications.

| S-EPMC9041146 | biostudies-literature

A new solvothermal method for the synthesis of size-controlled YAG:Ce single-nanocrystals.

Project description:Ce3+-doped Y3Al5O12 (YAG:Ce) nanocrystals were synthesized by a unique solvothermal method, under sub-critical conditions. A home-made autoclave was used, operating in a larger pressure and temperature range than that with conventional commercial equipment and allowing direct in situ photoluminescence (PL) and X-ray absorption characterizations. The study of various synthesis conditions (pressure, temperature, precursor concentration, reaction time) allowed the best reaction conditions to be pinpointed to control YAG:Ce nanocrystal size, as well as crystal quality, and to get efficient optical properties. Without any post thermal treatment, we succeeded in obtaining well-crystallized YAG:Ce nanocrystals (30-200 nm), displaying typical PL properties of YAG:Ce with a maximal emission at 550 nm. The pristine 100 nm-sized YAG:Ce nanoparticles present an internal quantum yield of about 40 ± 5%. In situ X-ray absorption near edge spectroscopy demonstrates the presence of Ce4+ in nanocrystals elaborated at high temperature, resulting from the oxidation of Ce3+ during the crystallization process.

| S-EPMC9083342 | biostudies-literature

Non-conventional Ce:YAG nanostructures via urea complexes.

Project description:Ce:YAG nanostructures (Ce:YAG = Cerium in Yttrium Aluminium Garnet), easy to control and shape, have been prepared via templating approach using natural and synthetic materials (i.e. paper, cotton wool and glass wool) previously soaked with a gel-like metals precursor and then thermally treated to achieve the wished morphology. The final material, otherwise difficult to process, can be easily moulded, it is lightweight, portable and forms, at the nanoscale, homogeneous layers of interconnected but not agglomerated nanoparticles (15 ± 5 nm). Using the same synthetic route, called Urea-Glass-Route, but in absence of a template, extremely pure Ce:YAG nanoparticle (45 ± 5 nm) can be also prepared, highly crystalline and well-defined in size and shape. Both structural and optical properties of the final materials were investigated, showing high optical quality. The support allows the production of a multifunctional material with mouldable shape and potential lighting application for large structures combining the strength, chemical durability, fire resistance, and translucency of glass fibres. Last, but not least, the synthetic path also allows an easy scaling up of the process: the first, key step for practical application of nanosized rare-earth doped YAG on large scale.

| S-EPMC6399219 | biostudies-literature

Synthesis and photoluminescence properties of silica-modified SiO2@ANA-Si-Tb@SiO2, SiO2@ANA-Si-Tb-L@SiO2 core-shell-shell nanostructured composites.

Project description:Three novel core-shell nanostructured composites SiO2@ANA-Si-Tb, SiO2@ANA-Si-Tb-L (L = second ligand) with SiO2 as the core and terbium organic complex as the shell were successfully synthesized. The core and shell were connected together by covalent bonds. The terbium ion was coordinated with organic ligand-forming terbium organic complex in the shell layer. The organosilane (HOOCC5H4NN(CONH(CH2)3Si(OCH2CH3)3)2 (abbreviated as ANA-Si) was used as the first ligand and 1,10-phenanthroline (phen) or 2-thenoyltrifluoroacetone (TTA) was used as the second ligand. Furthermore, silica-modified SiO2@ANA-Si-Tb@SiO2, SiO2@ANA-Si-Tb-L@SiO2 core-shell-shell nanostructured composites were also synthesized by sol-gel chemical route, which involved the hydrolysis and polycondensation processes of tetraethoxysilane (TEOS) using cetyltrimethyl ammonium bromide (CTAB) as a surface-active agent. An amorphous silica shell was coated around the SiO2@ANA-Si-Tb, SiO2@ANA-Si-Tb-L core-shell nanostructured composites. The core-shell and core-shell-shell nanostructured composites exhibited excellent luminescence in the solid state. Meanwhile, an improved luminescent stability property of the core-shell-shell nanostructured composites was observed for the aqueous solution. This type of core-shell-shell nanostructured composites exhibited bright luminescence, high stability and good solubility, which may present potential applications in the fields of optoelectronic devices, bio-imaging, medical diagnosis and study on the structure of function composite materials.

| S-EPMC6731695 | biostudies-literature

Enhancement of silicon modulating properties in the THz range by YAG-Ce coating.

Project description:Y3Al5-xGaxO12:Ce3+,V3+ (YAG:Ce) has excellent chemical stability and unprecedented luminous efficiency. Its strong photoresponsive property is thoroughly utilized in designing excellent optical information storage device. Here, the remarkable photoconductivity of YAG:Ce is exploited to demonstrate a hybrid YAG:Ce-silicon device that shows high speed terahertz wave spatial modulation. A wide terahertz spectra modulation is observed under different pump powers in frequency range from 0.2 to 1.8 THz. Furthermore, a dynamic control of the terahertz wave intensity is also observed in the transmission system. The modulation speed and depth of the device is measured to be 4 MHz (vs 0.2 kHz)and 83.8%(vs50%) for bare silicon, respectively. The terahertz transmission spectra exhibits highly efficiency terahertz modulation by optically pumping a YAG:Ce film on silicon with low optical pump fluence.

| S-EPMC7171083 | biostudies-literature

Oxygen vacancies induced photoluminescence in [Formula: see text] nanophosphors probed by theoretical and experimental analysis.

Project description:We report, for the first time, the influence of oxygen vacancies on band structure and local electronic structure of [Formula: see text] (SZO) nanophosphors by combined first principle calculations based on density functional theory and full multiple scattering theory, correlated with experimental results obtained from X-ray absorption and photoluminescence spectroscopies. The band structure analysis from density functional theory revealed the formation of new energy states in the forbidden gap due to introduction of oxygen vacancies in the system, thereby causing disruption in intrinsic symmetry and altering bond lengths in SZO system. These defect states are anticipated as origin of observed photoluminescence in SZO nanophosphors. The experimental X-ray absorption near edge structure (XANES) at Zn and Sr K-edges were successfully imitated by simulated XANES obtained after removing oxygen atoms around Zn and Sr cores, which affirmed the presence and signature of oxygen vacancies on near edge structure.

| S-EPMC7567121 | biostudies-literature

Red, Green, and Blue Photoluminescence of Ba₂SiO₄:M (M = Eu3+, Eu2+, Sr2+) Nanophosphors.

Project description:Divalent europium doped barium orthosilicate is a very important phosphor for the production of light emitting diodes (LEDs), generally associated to the green emission color of micron-sized crystals synthesized by means of solid-state reactions. This work presents the combustion synthesis as an energy and time-saving preparation method for very small nano-sized Ba₂SiO₄ particles, flexibly doped to acquire different emission energies. The size of the resulting spherical nanoparticles (NPs) of the green emitting Ba₂SiO₄:Eu2+ was estimated to about 35 nm applying the Scherrer equation and further characterized with aid of atomic force microscopy (AFM) as well as scanning electron microscopy (SEM). This phosphor is able to build homogeneous luminescent suspensions and was successfully down-sized without changing the optical properties in comparison to the bulk phosphors. Besides the X-ray diffraction (XRD) analysis and the different types of microscopy, the samples were characterized by luminescence spectroscopy. Undoped Ba₂SiO₄ NPs are not luminescent, but show characteristic red emission of the ⁵D₀ → ⁷FJ (J = 0-4) electronic transitions when doped with Eu3+ ions. Moreover, these orthosilicate nanoparticles generate blue light at low temperatures due to impurity-trapped excitons, introduced by the partial substitution of the Ba2+ with Sr2+ ions in the Ba₂SiO₄ lattice causing a substantial distortion. A model for the temperature behavior of the defect luminescence as well as for their nature is provided, based on temperature-dependent luminescence spectra and lifetime measurements.

| S-EPMC5521235 | biostudies-other

Microstructure and properties of additively manufactured Al-Ce-Mg alloys.

Project description:Additive manufacturing of aluminum alloys is largely dominated by a near-eutectic Al-Si compositions, which are highly weldable, but have mechanical properties that are not competitive with conventional wrought Al alloys. In addition, there is a need for new Al alloys with improved high temperature properties and thermal stability for applications in the automotive and aerospace fields. In this work, we considered laser powder bed fusion additive manufacturing of two alloys in the Al-Ce-Mg system, designed as near-eutectic (Al-11Ce-7Mg) and hyper-eutectic (Al-15Ce-9Mg) compositions with respect to the binary L → Al + Al11Ce eutectic reaction. The addition of magnesium is used to promote solid solution strengthening. A custom laser scan pattern was used to reduce the formation of keyhole porosity, which was caused by excessive vaporization due to the high vapor pressure of magnesium. The microstructure and tensile mechanical properties of the alloys were characterized in the as-fabricated condition and following hot isostatic pressing. The two alloys exhibit significant variations in solidification structure morphology. These variations in non-equilibrium solidification structure were rationalized using a combination of thermodynamic and thermal modeling. Both alloys showed higher yield strength than AM Al-10Si-Mg for temperatures up to 350 °C and better strength retention at elevated temperatures than additively manufactured Scalmaloy.

| S-EPMC7998028 | biostudies-literature

Computer Alloy Design of Ti Modified Al-Si-Mg-Sr Casting Alloys for Achieving Simultaneous Enhancement in Strength and Ductility.

Project description:In this paper, an efficient design of a Ti-modified Al-Si-Mg-Sr casting alloy with simultaneously enhanced strength and ductility was achieved by integrating computational thermodynamics, machine learning, and key experiments within the Bayesian optimization framework. Firstly, a self-consistent Al-Si-Mg-Sr-Ti quinary thermodynamic database was established by the calculation of phase diagram method and verified by key experiments. Based on the established thermodynamic database, a high-throughput Scheil-Gulliver solidification simulation of the A356-0.005Sr alloy with different Ti contents was carried out to establish the "composition-microstructure" quantitative relationship of the alloy. Then, by combining the computational thermodynamic, machine learning, and experimental data within the Bayesian optimization framework, the relationship "composition/processing-microstructure-properties" of A356-0.005Sr with different Ti contents was constructed and validated by the key experiments. Furthermore, the optimum alloy composition of the Ti-modified A356-0.005Sr casting alloy was designed based on this integration method with the Bayesian optimization framework and verified by the experiments. It is anticipated that the present integration method may serve as a general one for the efficient design of casting alloys, especially in the high-dimensional composition space.

| S-EPMC9822033 | biostudies-literature

Nanostructuration of YAG:Ce Coatings by ZnO Nanowires: A Smart Way to Enhance Light Extraction Efficiency.

Project description:In this study, we report on the enhancement of the light extraction efficiency of sol-gel-derived Y3Al5O12:Ce3+ (YAG:Ce) coatings using ZnO nanowire (NW) arrays. The ZnO NWs were grown by hydrothermal synthesis from a ZnO seed layer directly deposited on a YAG:Ce coating. Highly dense and vertically aligned ZnO NW arrays were evidenced on the top of the YAG:Ce coating by electron microscopy. A photoluminescence study showed that this original design leads to a different angular distribution of light together with an increase in emission efficiency of the YAG:Ce coating upon blue excitation, up to 60% more efficient compared to a non-structured YAG:Ce coating (without NWs). These improvements are ascribed to multi-scattering events for photons within the structure, allowing them to escape from the phosphor layer by taking optical paths different from those of the non-structured coating. This strategy of light extraction enhancement appears to be very promising, since it uses soft chemical processes and cheap ZnO NWs and is applicable to any sol-gel-derived luminescent coating.

| S-EPMC9332156 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data