Arduino-based, low-cost imaging incubator for extended live cell imaging
Ontology highlight
ABSTRACT:
SUBMITTER: Rossi V
PROVIDER: S-EPMC9438404 | biostudies-literature | 2022 May
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:An unacceptably large number of newborn infants die in developing countries. For a considerable number of cases (particularly in preterm infants), morbidity and mortality can be reduced by simply maintaining newborn thermal homeostasis during the first weeks of life. Unfortunately, deaths caused by prematurity remain inordinately common in low- and middle-income countries (LMICs) due to reduced access to incubators in light of the high cost of commercially available devices. We herein describe and test a low-cost and easy-to-assemble neonatal incubator created with inexpensive materials readily available in LMICs. The incubator is based on an Arduino microcontroller. It maintains controlled temperature and relative humidity inside the main chamber while continuously measuring newborn weight progress. Moreover, the incubator has a tilting bed system and an additional independent safety temperature alarm. The performance of the novel low-cost neonatal incubator was evaluated and successfully passed the IEC 60601-2-19 standards. In the present work, we provide all the necessary technical information, which is distributed as open source. This will enable assembly of very low-cost (<250 €) and fully functional incubators in LMICs that should help reduce neonatal mortality.
| S-EPMC10393824 | biostudies-literature
Project description:Lateral Flow Assays (LFA) have been one of the most widely adopted technologies in clinical diagnosis over recent years, especially during the COVID-19 pandemic, due to their feasibility, compactness, and rapid readout. However, the precise dispensing of antibodies-a key part of the fabrication process-requires costly line dispenser equipment, which poses a challenge to researchers with limited budgets. This study aims to resolve this key issue by introducing a Syringe-based Arduino-operated Low-cost Antibody Dispenser (SALAD). By utilizing a microneedle, stepper motor-driven syringe pump, and conveyor belt, SALAD can form micro-droplets to create an even band of antibodies. Our evaluation results showed comparable performance between SALAD and a commercialized model - Claremont ALFRD, with SALAD exceeding in affordability and feasibility. SALAD yielded an even signal, uniform bandwidth, and low background noise, yet optimization in the conveyor belt should be considered to enhance stability. With a low manufacturing cost ($200.61) compared to the commercialized models, our model is expected to provide an affordable approach for LFA researchers.
| S-EPMC10366588 | biostudies-literature
Project description:A novel portable low-cost Arduino-controlled photo- and fluorimeter for on-site measurements has been developed. The device uses LEDs as a light source and a phototransistor as a light sensor. The circuit is based on the discharge of a capacitor with the photocurrent from the phototransistor. Validation experiments for absorbance measurements were performed by measuring protein concentration using the Bradford method and measuring phosphate ions in water using a commercial test kit. The emission light of the excited fluorescent dyes rhodamine 6G and calcofluor white was measured to validate the usability of the device as a fluorescence photometer. In all validation experiments, similar correlation coefficients and limit of detection could be achieved with the portable photo- and fluorimeter and a laboratory spectrometer and fluorimeter. Real sample analysis was performed, measuring phosphate concentration in freshwater and concentration of green fluorescent protein, extracted from Escherichia coli.
| S-EPMC9609715 | biostudies-literature
Project description:Growth in open-source hardware designs combined with the decreasing cost of high-quality 3D printers have supported a resurgence of in-house custom lab equipment development. Herein, we describe a low-cost (< $400), open-source CO2 incubator. The system is comprised of a Raspberry Pi computer connected to a 3D printer controller board that has controls for a CO2 sensor, solenoid valve, heater, and thermistors. CO2 is supplied through the sublimation of dry ice stored inside a thermos to create a sustained 5% CO2 supply. The unit is controlled via G-Code commands sent by the Raspberry Pi to the controller board. In addition, we built a custom software application for remote control and used the open-source Grafana dashboard for remote monitoring. Our data show that we can maintain consistent CO2 and temperature levels for over three days without manual interruption. The results from our culture plates and real-time PCR indicate that our incubator performed equally well when compared to a much more expensive commercial CO2 incubator. We have also demonstrated that the antibiotic susceptibility assay can be performed in this low-cost CO2 incubator. Our work also indicates that the system can be connected to incubator chambers of various chamber volumes.
| S-EPMC8172042 | biostudies-literature
Project description:Accessibility to potentiostats is crucial for research development in electrochemistry, but their cost is the principal drawback for their massive use. With the aim to provide an affordable alternative for resource-constrained communities, we present a low-cost, portable electrochemical workstation that integrates an open-source potentiostat based on Arduino and a smartphone application. This graphical user interface allows easy control of electrochemical parameters and real-time visualization of the results. This potentiostat can perform the most used electrochemical techniques of cyclic and linear voltammetry and chronoamperometry, with an operating range of ±225 μA and ±1.50 V, and results that are comparable with those obtained with commercial potentiostats. Three applications reported here demonstrate the capacity and the good performance of this low-cost potentiostat as a teaching tool: identification of redox pairs, electrochemical characterization of pencil graphite electrodes, and detection of heavy metals using an electrodeposited film of bismuth on the pencil graphite electrode. Furthermore, detailed schemes of the device and its software are entirely available, expecting to provide an open-source potentiostat easy to replicate to further support education in electrochemical fundamentals and instrumentation.
| S-EPMC7895749 | biostudies-literature
Project description:Graphical abstract Ion Mobility Spectrometry (IMS) provides low ppbv detection limits for gas-phase or aqueous analytes. These instruments rely an electric field to produce ion motion. This electric field is typically 200–600 V/cm with a 15 cm cell, requiring an HV source of 6–10 kV. In this work, we present a low-cost alternative for supplying this high voltage. Inexpensive, commercially available 0–20 kV HV modules are mapped to an analog 0–5 V input signal, controlled using an Arduino microcontroller and digital analog converter. Dual polarities are selectable through a front-panel switch and ramps potentials between settings to avoid damage to attached devices.
| S-EPMC9731844 | biostudies-literature
Project description:In the last two decades, the need for seawater pH control methodologies paralleled the rise in attention to the biological impacts of ocean acidification. Many effective and high-performing systems have been created, but they are often expensive, complex, and difficult to establish. We developed a system that is similarly high performing, but at a low cost and with a simple and accessible design. This system is controlled by an Arduino Nano, an open-source electronics platform, which regulates the flow of CO2 gas through electric solenoid valves. The Arduino and other inexpensive materials total ∼$150 (plus CO2 gas and regulator), and a new treatment can be added for less than $35. Easy-to-learn code and simple wire-to-connect hardware make the design extremely accessible, requiring little time and expertise to establish. The system functions with a variety of pH probes and can be adapted to fit a variety of experimental designs and organisms. Using this set up, we were able to constrain seawater pH within a range of 0.07 pH units. Our system thus maintains the performance and adaptability of existing systems but expands their accessibility by reducing cost and complexity.
| S-EPMC9123462 | biostudies-literature
Project description:Long-term live cell imaging requires sophisticated and fully automated commercial-stage incubators equipped with specified inverted microscopes to regulate temperature, CO2 content, and humidity. In this study, we present a CO2-free on-stage incubator specifically designed for use across various cell culture platforms, enabling live cell imaging applications. A simple and transparent incubator was fabricated from acrylic sheets to be easily placed on the stages of most inverted microscopes. We successfully performed live-cell imaging of cholangiocarcinoma (CCA) cells and HeLa cell dynamics in both 2D and 3D microenvironments over three days. We also analyzed directed cell migration under high serum induction within a microfluidic device. Interesting phenomena such as "whole-colony migration", "novel type of collective cell migration" and "colony formation during cell and colony migration" are reported here for the first time, to the best of our knowledge. These phenomena may improve our understanding of the nature of cell migration and cancer metastasis.
| S-EPMC11417791 | biostudies-literature
Project description:Fluorescent reporters have revolutionized modern applications in the fields of molecular and synthetic biology, enabling applications ranging from education to point-of-care diagnostics. Past advancements in these fields have primarily focused on improving reaction conditions, the development of new applications, and the broad dissemination of these technologies. However, field and classroom-based applications have remained limited in part due to the nature of fluorescent signal detection, which often requires the use of costly lab equipment to observe and quantify fluorescence readouts. Users without access to laboratory equipment rely on qualitative assessments of fluorescence, a process that remains highly variable from user-to-user even within the same classroom. To overcome this challenge, we have developed a foldable illuminator and incubator device to support field-applications of synthetic biology-based biosensors for education and diagnostics. The Fold-Illuminator is an affordable, portable, and recyclable device that allows for the visible detection of fluorescent biomolecules. The Fold-Illuminator's design allows for assembly in under 10 min, a user can then utilize the optional heating element to incubate biochemical reactions and visualize fluorescence outputs in a defined and light-controlled environment. Interchangeable LED strips and light-filtering screens provide modularity to pair with the fluorescence wavelengths of interest. The user can then unfold the device for convenient storage, transport, or even recycling. The cost for the Fold-Illuminator is $5.58 USD and is compatible with an optional heating element for an additional $3.98 cost, with potential for further reductions in cost for larger quantities. Open-source templates for cutting device parts from paper stock are provided for both printing and cutting by hand; cutting can also be achieved with consumer-grade smart cutting machines such as the Cricut®. Combined with the broad applications of fluorescent reporters, the Fold-Illuminator has the potential to improve access to fluorescence visualization and quantification for new users as well as emerging field applications.
| S-EPMC8099501 | biostudies-literature
Project description:The tissue engineering community has been vocal regarding the need for noninvasive instruments to assess the development of tissue-engineered constructs. Medical imaging has helped fulfill this role. However, specimens allocated to a test tube for imaging cannot be tested for a prolonged period or returned to the incubator. Therefore, samples are essentially wasted due to potential contamination and transfer in a less than optimal growth environment. In turn, we present a standalone, miniature, magnetic resonance imaging-compatible incubator, termed the e-incubator. This incubator uses a microcontroller unit to automatically sense and regulate physiological conditions for tissue culture, thus allowing for concurrent tissue culture and evaluation. The e-incubator also offers an innovative scheme to study underlying mechanisms related to the structural and functional evolution of tissues. Importantly, it offers a key step toward enabling real-time testing of engineered tissues before human transplantation. For validation purposes, we cultured tissue-engineered bone constructs for 4 weeks to test the e-incubator. Importantly, this technology allows for visualizing the evolution of temporal and spatial morphogenesis. In turn, the e-incubator can filter deficient constructs, thereby increasing the success rate of implantation of tissue-engineered constructs, especially as construct design grows in levels of complexity to match the geometry and function of patients' unique needs.
| S-EPMC4382823 | biostudies-literature