Dataset Information

Photocatalytic Aerobic Oxidation of Biomass-Derived 5-HMF to DFF over MIL-53(Fe)/g-C3N4 Composite.

ABSTRACT: A MIL-53(Fe)/g-C3N4 heterogeneous composite was synthesized and applied in photocatalytic oxidation of 5-hydroxymethylfurfural (5-HMF) to 2,5-diformylfuran (DFF). The systematic investigation indicated that the introduction of MIL-53(Fe) into g-C3N4 increased the specific surface area, broadened the visible-light response region, and promoted the separation efficiency of the photo-generated electron-hole pairs. The 10% MIL-53(Fe)/g-C3N4 heterogeneous composite achieved the best photocatalytic oxidation activity with 74.5% of 5-HMF conversion under simulated sunlight, which was much higher than that of pristine g-C3N4 and MIL-53(Fe). The MIL-53(Fe)/g-C3N4 composite displayed good photocatalytic reusability and stability. Based on the characterization results and photocatalytic performance, a Z-scheme photocatalytic mechanism of the MIL-53(Fe)/g-C3N4 composite was suggested, and a possible reaction route was deduced.

SUBMITTER: Huang D

PROVIDER: S-EPMC9740462 | biostudies-literature | 2022 Dec

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Photocatalytic Aerobic Oxidation of Biomass-Derived 5-HMF to DFF over MIL-53(Fe)/g-C3N4 Composite.

Huang Danyao D Wang Hao H Wu Ying Y

Molecules (Basel, Switzerland) 20221204 23

A MIL-53(Fe)/g-C3N4 heterogeneous composite was synthesized and applied in photocatalytic oxidation of 5-hydroxymethylfurfural (5-HMF) to 2,5-diformylfuran (DFF). The systematic investigation indicated that the introduction of MIL-53(Fe) into g-C3N4 increased the specific surface area, broadened the visible-light response region, and promoted the separation efficiency of the photo-generated electron-hole pairs. The 10% MIL-53(Fe)/g-C3N4 ...[more]

PMID: 36500631

Similar Datasets

Project description:In this study, hybrids of nanoporous MIL-101(Cr) and MIL-53(Al) were synthesized using a hydrothermal method for various time periods, ranging from 8 to 40 h. The prepared materials were characterized by powder X-ray diffraction (PXRD) and elemental analysis, and their specific surface areas were measured by N2 sorption at 77 K using the Brunauer-Emmett-Teller (BET) method. To investigate the practical application of these materials, the pure carbon dioxide and methane adsorption capacities of the samples were determined using the volumetric method. The Langmuir model was used to fit the CO2 and CH4 isotherms. Extended Langmuir (EL) equations and the ideal adsorbed solution theory (IAST) models were used to obtain the CO2/CH4 selectivity. The sample with the highest BET specific surface area was selected as a candidate for further investigations. The thermal stability of the selected sample was investigated by thermogravimetric analysis (TGA). Scanning electron microscopy (SEM) was used to characterize the sample morphology. XRD results showed that the sample synthesized over the shortest time corresponded to MIL-101(Cr), while the sample synthesized over the longest time was in agreement with MIL-53(Al). Samples synthesized for time periods between these two limits were assumed to be composites of both MIL-53(Al) and MIL-101(Cr). TGA results indicated that the hybrid materials were thermally stable at temperatures about 100 °C higher than for pure MIL-101(Cr). The BET specific surface area (1746 m2 g-1) and CO2 adsorption capacity (16 mmol g-1) of the selected hybrid sample were about 50% and 35% higher, respectively, compared with those of pure MIL-53(Al), but 30% and 20% lower, respectively, compared with those of pure MIL-101(Cr). Binary adsorption modeling showed the high selectivity of the MIL-101(Cr) and MIL-53(Al) hybrid material for CO2 with a minimum separation factor of about 60 at 298 K. This value was much higher than those reported previously and those observed in this work for the original MIL-101(Cr) or MIL-53(Al). These results demonstrated that the hybrid of MIL-101(Cr) and MIL-53(Al) was a promising material for selective CO2 capture from natural and biogas.

Dataset Information

Photocatalytic Aerobic Oxidation of Biomass-Derived 5-HMF to DFF over MIL-53(Fe)/g-C3N4 Composite.

Publications

Photocatalytic Aerobic Oxidation of Biomass-Derived 5-HMF to DFF over MIL-53(Fe)/g-C<sub>3</sub>N<sub>4</sub> Composite.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets