RNA-BisSeq for YBX1 RIP in normal T24 cell
Ontology highlight
ABSTRACT:
ORGANISM(S): Homo sapiens
PROVIDER: GSE133625 | GEO | 2019/07/02
REPOSITORIES: GEO
Similar Datasets
Project description:Immunoaffinity Purifications of Human Argonaute Twelve hours after transfections with mock or with miR-124, we washed each 15-cm plate once with phosphate-buffered saline (usually two plates were used per IP), then added 1 ml of 4 C lysis buffer (150 mM KCl, 25 mM Tris-HCl [pH 7.4], 5 mM Na-EDTA [pH 8.0], 0.5% Nonidet P-40, 0.5 mM DTT, 10 ul protease inhibitor cocktail [Pierce Cat# 78437], 100 U/ml SUPERaseIn [Ambion Cat# AM2694]). Following a 30-min incubation at 4 C, we scraped the plates, combined the lysates, and then spun them at 4 C for 30 min at 14,000 RPM in a microcentrifuge. We collected the supernatant and filtered it through a 0.45-um syringe filter. We froze an aliquot of lysate in liquid nitrogen for reference RNA isolation. We then added 0.22 mg/ml heparin to the lysate. We mixed the lysate with 2.5 mg of Dynal m-280 streptavidin beads (250 ul from original storage solution) coupled to biotinylated 4F9 ago antibody (~12.5 ug), which we equilibrated immediately prior to use by washing twice with 1 ml of lysis buffer. We incubated the beads with the lysate for 2 h at 4 C and then washed the beads twice with 1.25 ml of ice-cold lysis buffer for 5-min each. Five percent of the beads were frozen for SDS PAGE analysis after the second wash. RNA was extracted directly from the remaining beads using lysis buffer from Invitrogen's Micro-to-Midi kit (Invitrogen Cat# 12183-018). We purified RNA from the lysate and RNA extracted from the beads with the Micro-to-Midi kit as per vender's instructions, except that the percentage isopropanol used for binding to the column was 70%, instead of 33%, to promote the binding of small RNAs. RNA was amplified with ambion kit 1755. RNA from total cell lysate was labeled with cy3 and IPd RNA was labeled with cy5
2009-11-10 | GSE18834 | GEO
Project description:Immunoaffinity Purifications of Human Argonaute Twelve hours after transfections with mock or with miR-124, we washed each 15-cm plate once with phosphate-buffered saline (usually two plates were used per IP), then added 1 ml of 4 C lysis buffer (150 mM KCl, 25 mM Tris-HCl [pH 7.4], 5 mM Na-EDTA [pH 8.0], 0.5% Nonidet P-40, 0.5 mM DTT, 10 ul protease inhibitor cocktail [Pierce Cat# 78437], 100 U/ml SUPERaseIn [Ambion Cat# AM2694]). Following a 30-min incubation at 4 C, we scraped the plates, combined the lysates, and then spun them at 4 C for 30 min at 14,000 RPM in a microcentrifuge. We collected the supernatant and filtered it through a 0.45-um syringe filter. We froze an aliquot of lysate in liquid nitrogen for reference RNA isolation. We then added 0.22 mg/ml heparin to the lysate. We mixed the lysate with 2.5 mg of Dynal m-280 streptavidin beads (250 ul from original storage solution) coupled to biotinylated 4F9 ago antibody (~12.5 ug), which we equilibrated immediately prior to use by washing twice with 1 ml of lysis buffer. We incubated the beads with the lysate for 2 h at 4 C and then washed the beads twice with 1.25 ml of ice-cold lysis buffer for 5-min each. Five percent of the beads were frozen for SDS PAGE analysis after the second wash. RNA was extracted directly from the remaining beads using lysis buffer from Invitrogen's Micro-to-Midi kit (Invitrogen Cat# 12183-018). We purified RNA from the lysate and RNA extracted from the beads with the Micro-to-Midi kit as per vender's instructions, except that the percentage isopropanol used for binding to the column was 70%, instead of 33%, to promote the binding of small RNAs. RNA was amplified with ambion kit 1755. RNA from total cell lysate was labeled with cy3 and IPd RNA was labeled with cy5 An all pairs experiment design type is where all labeled extracts are compared to every other labeled extract.
2010-06-20 | E-GEOD-18834 | biostudies-arrayexpress
Project description:Glioblastoma stem cells (TS-543) were harvested and cross-linked with 1% formaldehyde for 10 mins at room temperature. The cells were lysed using SDS Lysis buffer for ChIP (1% SDS, 10 mM EDTA, 50 mM Tris-HCl pH 8). The lysate was then sonicated for 25 cycles at 30% amplitude (15 s ON and 45 s OFF). The sonicated samples were then diluted in ChIP dilution buffer (0.01% SDS, 1% Triton-X-100, 1.2 mM EDTA, 16.7 mM Tris–HCl pH 8, 167 mM NaCl) and used for the immunoprecipitation with H3K27ac (Abcam, Ab4729), H2AZ (Active motive, cat#39113) and H3K27ac (Abcam cat#ab8580). After an over-night incubation with antibody, the bound DNA was washed sequentially with low salt wash buffer (0.1% SDS, 1% Triton X 100, 2 mM EDTA, 20 mM Tris–HCl pH 8, 150 mM NaCl), high salt wash buffer (0.1% SDS, 1% Triton X-100, 2 mM EDTA, 20 mM Tris–HCl pH 8, 500 mM NaCl), LiCl wash buffer (0.25 M LiCl, 1% NP40, 1%deoxycholate, 1 mM EDTA, 10 mM Tris–HCl pH 8) and TE wash buffer (10 mM Tris–HCl pH 8, 1 mM EDTA) to remove non-specific sequences and eluted in the elution buffer (84 mg NaHCO3, 1 ml 10% SDS, 9 ml H2O). Then the samples were reverse cross-linked using NaCl at 65°C overnight. The eluted DNA was purified and used for library preparation. Library preparation was performed as previously described as described in Bowman et al. BMC Genomics 2013. Briefly, end repair with NEBNext End Repair enzyme (NEB, E6050) and clean-up with 2.4x volume AMPure XP beads (Beckman Coulter, A63880). A-tailing with Klenow Fragment (NEB, M0212) and purified with 2.4x volume AMPure XP beads. Adapter ligation reactions contained annealed universal adapter and T4 rapid ligase (NEB, B0202) and clean-up with 1.8x volume AMPure XP beads. Chromatin was amplified using KAPA Real-time Library Amplification Kit (KAPABIOSYSTEMS, KK2701) with universal primer and barcoded primer. Amplified chromatin was purified with QIAquick Gel Extraction Kit (Qiagen) and sequenced paired-end with Illumina NextSeq 500.
2021-09-05 | GSE152862 | GEO
Project description:Cells were washed with cold PBS twice and scraped from the plates, then centrifuged at 1000 rpm for 5 min to pellet cells. Washed cells were lysed with 400 L of cell lysis buffer (10 mM Tris-HCl pH7.5, 150 mM NaCl, 0.15% NP-40 and proteinase inhibitor cocktail) and incubated on ice for 10 min. The suspension was carefully add at the top of sucrose buffer (10 mM Tris-HCl pH7.5, 150 mM NaCl, 24% sucrose), and centrifuged at 3200g for 10 min to collect nuclear pellets. Pellets were resuspended in 250 L of Glycerol buffer (20 mM Tris-HCl pH7.5, 75 mM NaCl, 0.5 mM EDTA pH8.0, 50% glycerol), then then immediately add 250 μl Nuclear lysis buffer (10 mM Tris-HCl pH7.5, 300 mM NaCl, 7.5 mM MgCl2, 0.2 mM EDTA pH8.0, 1% NP-40, 1M urea). Mix by vortexing for 4 s and incubate on ice for 2 min. Centrifuge the lysate at 13,000 × g for 2 min to precipitate the chromatin–RNA complex. Briefly rinse the chromatin pellets with PBS-EDTA. RNA was extracted with Trizol reagent. RNA libraries were prepared according to manual of SMARTer smRNA-Seq Kit for Illumina (Clontech, 635031).
2019-10-15 | GSE134103 | GEO
Project description:Parasite lysates were centrifuged (20,000 g, 4°C, 15 min). Beads (blank and with linker attached) were washed 3× with water then twice with lysis buffer. The lysate (~2 mg total protein) was first incubated with 2 mg blank beads for 30 min at 4°C with rotating agitation. The lysate was divided into two then incubated with either 1% DMSO or 100 µM DDD01510706 (competitor) for 30 min at 4°C with agitation. Finally, lysates were incubated with 2 mg of compound-bound beads for 1 h at 4°C with agitation. The beads were then washed 3× with wash buffer (0.8% (w/v) octyl β-D-glucopyranoside, 50 mM Tris pH 8.0, 5 mM EDTA, 1 mg/mL BSA) and 2× Tris-buffered saline (TBS; 50 mM Tris-Cl pH 7.5, 150 mM NaCl). Samples were run 1.5 cm into a Bis-Tris 10% (w/v) acrylamide gel and stained with Coomassie quick reagent for 30 min. The entire gel bands were removed and subjected to in-gel reduction with 10 mM dithiothreitol, alkylation with 50 mM iodoacetamide and digestion with 12.5 μg/mL trypsin (Pierce) for >16 h at 37°C. Recovered tryptic peptides were then vacuum dried prior to analysis
2022-10-15 | PXD033740 | Pride
Project description:Purpose: Investigation of DDX41 chromatin binding sites in U2OS cells Method: Expression of DDX41-GFP was induced for 48 hours before crosslinking using 1µg/ml docycycline. Control cells were not induced with doxycline. Cells were mildly crosslinked using 1% FA for 2 min at RT. Concanavalin A-coated beads were activated in Binding Buffer (20 mM Hepes-KOH pH 7.9, 10 mM KCl, 1mM CaCl2, 1 mM MnCl2).1*10^6 U2OS cells were washed twice with Wash Buffer (Hepes-NaOH pH7.5, 150 mM NaCl, 0.5 mM Spermidine, 1 mM protease inhibitor) at room temperature and afterwards immobilized on the activated beads in 1 ml Wash Buffer. Cells were permeabilized with 0.05% digitonin in Wash buffer for 4 min at RT. 1 µg Nanobody-GFP-MNase (in-house protein production, PMID:25362362) binding was performed at 4°C for 30 min in 0.05% digitonin-Wash buffer. After 2x washing, the MNase was activated by adding 3mM CaCl2 on ice for 30 min. 2x Stop Buffer (68 µl 5M NaCl, 40 µl 0.5 M EDTA, 20 µl 0.2 M EGTA, 10 µl 5% digitonin, 5 µl 10mg/ml RnaseA, )) was mixed with the samples to stop the reaction. Chromatin fragments were released by incubating the samples for 20 minutes at 37°C and centrifugation at 16.000×g for 10 minutes at 4°C. Supernatants were incubated at 70°C in the presence of 0.1% SDS and 5 µg proteinase K. Before library preparation, the DNA was recovered by phenol-chloroform extraction Results: We succesfully mapped DDX41 binding sites on cromatin in U2OS cells. DDX41 preferentially binds in the promoter region of genes.
2021-11-17 | GSE183083 | GEO
Project description:T. cruzi epimastigotes in the logarithmic growth phase (3×106 cells mL-1) were incubated for 12h with bortezomib (1.8 µM), GNF6702 (2.9 µM) or compound 1 (24 µM), equivalent to 8× the EC50 values of each compound. Controls were incubated in the presence of diluent (DMSO). Cells were harvested by centrifugation (1912g, 15 min, 4 °C) and washed with ice-cold PBS (1912g, 5 min, 4 °C), and finally, the cell pellets were resuspended in 1.5 mL of ice-cold lysis buffer (1 mM EDTA, 1 mM DTT, 100 μM TLCK, and 1× Roche EDTA-free cOmplete protease inhibitor cocktail in 50 mM potassium phosphate buffer, pH 7.4). Cell suspensions were submitted to 3 freeze–thaw cycles in a dry ice/ethanol bath to biologically inactivate the parasites and then lysed using the One ShotTM Cell disruptor (Constant Systems, UK) at 30 kpsi.
2022-02-17 | PXD027524 | Pride
Project description:The chromatin fraction was isolated from 5x107 HeLa cells. Chromatin was digested in 100 mL of MNase (40 units/ mL ) reaction buffer for 3 min at 37 °C in a thermomixer (1,400 rpm). After addition of 10 L EGTA (25mM) to inactivate MNase, soluble digested chromatin was collected by 13,000 rpm centrifuge for 5 min. 10 mg of Pol II antibody was conjugated to magnetic protein A beads. The supernatant was diluted with 400 mL of NET-2 buffer and pSer2-Pol II antibody-conjugated beads were added. Incubated the IP reaction at 4 °C for 1 hr. The beads were washed with 1 mL of NET-2 buffer six times and 100 mL of 1xPNKT (1xPNK buffer and 0.05% Triton X-100) buffer once. Washed beads were incubated in 50 mL PNK reaction mix (1xPNKT, 1 mM ATP and 0.05 U/ml T4 PNK (NEB)) in Thermomixer at 37 °C, 1,400 rpm for 6 min. Beads were washed with 1 mL of NET-2 buffer once and RNA was extracted with Trizol reagent. RNA was suspended in urea Dye (7M Urea, 1xTBE, 0.1% BPB and 0.1% XC) and resolved on 6% TBU gel (Invitrogen) at 200 V for 5 min. Gels with 30-160 nt RNAs were collected. 0.2 mL tube was prepared with holes made with 25G needle and placed in a 1.5 mL tube. Gel fragments were placed in the layered tube and broken down by centrifugation at 12,000 rpm for 1 min. The small RNAs were eluted from gel using RNA elution buffer (1 M NaOAc and 1 mM EDTA) at 25 °C for 1 hr in Thermomixer (900 rpm). Eluted RNA was purified with SpinX column (Coster) with 2 glass filters (Millipore) and the flow-through RNA was ethanol precipitated.
2019-10-15 | GSE134102 | GEO
Project description:Biochemical purification: Five grams of adult flies or 2.5 g of embryos were used in each affinity purification. Flies or embryos were suspended in 15 ml of buffer B (buffer A plus 1.5 mM dithiothreitol [DTT], 1 mM phenylmethylsulfonylfluoride [PMSF], 0.5 5g/ml leupeptin, 0.8 5g/ml pepstatin, 20 U/ml DNase I, 100 U/ml RNasin [Promega], and 0.2 mg/ml heparin) in a mortar filled with liquid nitrogen and ground with a pestle to a fine powder. The powder was transferred to a glass-dounce, thawed and dounced until the pestle reached the bottom. The suspension was centrifuged twice at 40C and 10,000 g for 10 min. The fat layer on top was aspirated off after each centrifugation. Cleared extract (12.5 ml) was incubated with 600 5l of a slurry (50% [v/v]) of IgG-agarose beads (Sigma) for 90 min at 4C. The beads were washed once with buffer B for 15 min at 4C, and three times for 15 min at 4C with buffer C (20 mM TrisHCl [pH 8.0], 150 mM NaCl, 1 mM EDTA [pH 8.0], 10% glycerol, 0.01% NP-40, 1 mM DTT, 10 U/ml RNasin). PumHD was released from beads by incubation with 150 Units of AcTEV protease (Invitrogen) for 2 hr at room temperature (RT). RNA was isolated from extracts and from the TEV eluates with TRIZOL reagent (Invitrogen) followed by RNeasy Mini-Kit (Qiagen) purification according to the manufacturer's instructions. Microarray analysis: A pool of four control cDNAs (2 ng of each flp, gal4, lacZ and -Gal) was added to each RNA sample prior to labeling as controls for the labeling procedure. Total RNA (12 5g) derived from the extract and 300 ng or 30% of the affinity-isolated RNA were labeled with Cy3 and Cy5 fluorescent dyes, respectively, following cDNA synthesis with amino-allyl dUTP in addition to the four natural dNTPs using a 1:1 mixture of oligo(dT) and random nonamer primers. The Cy3- and Cy5-labeled cDNA samples were mixed and hybridized to Drosophila DNA microarrays. An all pairs experiment design type is where all labeled extracts are compared to every other labeled extract. Keywords: RNA IP
2006-02-28 | GSE3582 | GEO
Project description:gDNA was estracted and digested with cocktail of restrict enzymes MseI, DdeI, AluI, MboI, incubated at 37°C for 6 h. After purified by phenol/chloroform extraction, fragmented DNA was resuspended by TE, and quantified by Qubit 3.0 (Invitrogen). For each sample, 20 μg input DNA was immunoprecipitated overnight at 4°C in a shaker, with 1× DRIP binding buffer (10 mM NaPO4 pH 7.0, 140 mM NaCl, 0.05% Triton X-100) and 10 μg S9.6 antibody (ATCC, HB-8730). After adding 50 μl Dynabeads Protein G (Invitrogen, 10004D) and incubated for 4 h, the beads with antibody were washed by 1× DRIP binding buffer for 4 times at room temperature, each wash takes 10 min. Added 250 μl elution buffer (50 mM Tris pH 8.0, 10 mM EDTA, 0.5% SDS) and 5 U Proteinase K to beads/antibody complexes, incubated for 40 min in an Eppendorf ThermoMixer at 55°C, 1,000 rpm. Purified by phenol/chloroform extraction, and moved supernatant to a new tube, followed by adding 1/10 volume 3 M NaAc, 1 μl GlycoBlue (Invitrogen) and 1 volume isopropanol, precipitated at -20°C for 3 h and then centrifuged. After washed by 70% ethanol and dried, the DRIPed DNA pellet was resuspended by 75 μl low EDTA TE buffer (10 mM Tris-HCl 8.0, 0.1 mM EDTA). NGS libraries were constructed using Accel-NGS® 1S Plus DNA Library Kit (Swift Biosciences).
2019-10-15 | GSE134101 | GEO