Project description:ObjectivesThe aim of this study was to assess the clinical impact of 3 bifurcation angles in left main (LM) bifurcation treated with the 2-stent technique.BackgroundData are limited regarding the impact of bifurcation angles after LM percutaneous coronary intervention (PCI).MethodsUsing patient-level 4 multicenter registries in Korea, 462 patients undergoing LM bifurcation PCI with the 2-stent technique were identified (181 crush, 167 T-stenting; 63% 1st generation drug-eluting stent (DES), 37% 2nd generation DES). Three bifurcation angles, between the LM and left anterior descending (LAD), the LM and left circumflex (LCX), and the LAD and LCX, were measured. The primary outcome was target lesion failure (TLF), a composite of cardiac death, myocardial infarction, and target lesion revascularization (TLR).ResultsIn patients treated with the crush technique, the best cutoff value (BCV) to predict TLF was 152° of the LM-LAD angle. In the crush group, a significantly higher TLF rate, mostly driven by TLR, was observed in the LM-LAD angle ≥152° group compared with the <152° group (35.7% vs. 14.6%; adjusted hazard ratio 3.476; 95% confidence interval 1.612-7.492). An LM-LAD angle ≥152° was an independent predictor of TLF. In the T-stenting, no bifurcation angle affected the clinical outcomes.ConclusionsIn LM bifurcation PCI using the 2-stent technique, wide LM-LAD angle (≥152°) was associated with a greater risk of TLF in the crush, whereas none of the bifurcation angles affected T-stenting outcomes.
Project description:Left main coronary artery stenting requires rigorous planning and optimal execution. This case series presents a new approach to left main stenting guided by preprocedural patient-specific computational simulations. Three patients with significant left main artery disease underwent simulation-guided intervention using a novel stent scaffold purpose-built for large coronary arteries. (Level of Difficulty: Advanced.).
Project description:BackgroundOptimal deployment of coronary stents in a bifurcation lesion remains a matter of debate.AimsWe sought to capture the daily practice of bifurcation stenting by means of a worldwide registry and to investigate how post-implantation deployment techniques influence clinical outcomes.MethodsData from the e-ULTIMASTER registry were used to perform an analysis of 4,395 patients undergoing percutaneous coronary intervention for bifurcation lesions. Inverse probability of treatment weights (IPTW) propensity score methodology was used to adjust for any baseline differences. The primary outcome of interest was target lesion failure (TLF) at one year (follow-up rate 96.2%).ResultsThe global one-year TLF rate was low (5.1%). The proximal optimisation technique (POT) was used in 33.9% of cases and was associated with a reduction in the adjusted TLF rate (4.0% [95% confidence interval: 3.0-5.1%] vs 6.0% [5.1-6.9%], p<0.01) due to a reduction of all components of this composite endpoint, except for cardiac death. Stent thrombosis was also positively impacted (0.4% [0.04-0.7%] vs 1.3% [0.8-1.7%], p<0.01). POT benefit was uniform across subgroups. Conversely, the use of the kissing balloon technique (36.5%) did not influence the adjusted TLF rate.ConclusionsDespite a low one-year failure rate in this large bifurcation stenting cohort, POT was associated with a further reduction in the event rate and a uniform benefit across subgroups, suggesting systematic use of this deployment technique regardless of the bifurcation anatomy and stenting technique.
Project description:Left main (LM) coronary artery bifurcation stenting is a challenging topic due to the distinct anatomy and wall structure of LM. In this work, we investigated computationally and experimentally the mechanical performance of a novel everolimus-eluting stent (SYNERGY MEGATRON) purpose-built for interventions to large proximal coronary segments, including LM. MEGATRON stent has been purposefully designed to sustain its structural integrity at higher expansion diameters and to provide optimal lumen coverage. Four patient-specific LM geometries were 3D reconstructed and stented computationally with finite element analysis in a well-validated computational stent simulation platform under different homogeneous and heterogeneous plaque conditions. Four different everolimus-eluting stent designs (9-peak prototype MEGATRON, 10-peak prototype MEGATRON, 12-peak MEGATRON, and SYNERGY) were deployed computationally in all bifurcation geometries at three different diameters (i.e., 3.5, 4.5, and 5.0 mm). The stent designs were also expanded experimentally from 3.5 to 5.0 mm (blind analysis). Stent morphometric and biomechanical indices were calculated in the computational and experimental studies. In the computational studies the 12-peak MEGATRON exhibited significantly greater expansion, better scaffolding, smaller vessel prolapse, and greater radial strength (expressed as normalized hoop force) than the 9-peak MEGATRON, 10-peak MEGATRON, or SYNERGY (p < 0.05). Larger stent expansion diameters had significantly better radial strength and worse scaffolding than smaller stent diameters (p < 0.001). Computational stenting showed comparable scaffolding and radial strength with experimental stenting. 12-peak MEGATRON exhibited better mechanical performance than the 9-peak MEGATRON, 10-peak MEGATRON, or SYNERGY. Patient-specific computational LM stenting simulations can accurately reproduce experimental stent testing, providing an attractive framework for cost- and time-effective stent research and development.
Project description:BackgroundWhile radial stent deformation has been thoroughly investigated, data on longitudinal deformation are scarce.AimsThe aim of the study was to describe longitudinal stent deformation associated with the proximal optimisation technique (POT).MethodsLongitudinal stent deformation was assessed by bench testing and by clinical evaluation. Bench testing was performed in silicone models using 3.00 (n=15) and 3.50 mm (n=14) stent platforms. After deployment, stents were sequentially post-dilated in the proximal main branch up to 5.50 mm, in increments of 0.50 mm, in order to simulate a spectrum of overexpansion. Stent length was redefined by optical coherence tomography (OCT) after each step. Clinical data were collected retrospectively from OCT-guided bifurcation percutaneous coronary intervention cases.ResultsIn bench tests, POT has led to significant stent elongation in all cases. The magnitude of elongation was comparable between the 3.00 and the 3.50 mm stent platforms, with 0.86±0.74 mm vs 0.86±0.73 mm, respectively (p=0.71), per 0.5 mm overexpansion. For 3.00 mm stent platforms, maximal elongation was 4.31±1.47 mm after up to 5.5 mm overexpansion. For 3.50 mm platforms, maximal elongation was 2.87±0.94 mm after up to 5.5 mm overexpansion. Thirty-six clinical cases were analysed, of which 22 (61%) were performed in the distal left main. Post-dilation was performed with 0.98±0.36 mm absolute overexpansion, resulting in 2.22±1.35 mm elongation, as compared to nominal stent length.ConclusionsOverexpansion by POT results in proximal stent elongation. This has to be considered once the stent length is selected and the stent is positioned, especially in the left main stem, where proximal overexpansion is marked and accurate ostial landing is critical.
Project description:An extraperitoneal colostomy is not sufficiently effective in preventing parastomal hernias. On the basis of anatomic structures and mechanical principles, we modified this surgical technique by preserving the integrity of the posterior rectus abdominis sheath to prevent parastomal hernia, and we applied it clinically.