Browse
Submit Data
Databases
API
Help

Dataset Information

42 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Data from crosslinked PS honeycomb thin film by deep UV irradiation.

ABSTRACT: Thin polystyrene (PS) films with highly ordered honeycomb pattern were successfully fabricated by an improved phase separation method. The PS film was successfully crosslinked after applying a deep UV irradiation. This work presents a proof of crosslinking PS by characterizing ATR-FTIR, TGA and the wetting property of the honeycomb films, which were prepared using a solvent/non-solvent ratio of 90/10, before and after 6 h of UV irradiation.

SUBMITTER: Bui VT

PROVIDER: S-EPMC4688971 | biostudies-literature | 2015 Dec

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Publications

Data from crosslinked PS honeycomb thin film by deep UV irradiation.

Bui Van-Tien VT Lee Hwa Su HS Choi Jae-Hak JH Choi Ho-Suk HS

Data in brief 20151117

Thin polystyrene (PS) films with highly ordered honeycomb pattern were successfully fabricated by an improved phase separation method. The PS film was successfully crosslinked after applying a deep UV irradiation. This work presents a proof of crosslinking PS by characterizing ATR-FTIR, TGA and the wetting property of the honeycomb films, which were prepared using a solvent/non-solvent ratio of 90/10, before and after 6 h of UV irradiation. ...[more]

PMID: 26793742

Similar Datasets

Deep-Ultraviolet Transparent Conductive MWCNT/SiO2 Composite Thin Film Fabricated by UV Irradiation at Ambient Temperature onto Spin-Coated Molecular Precursor Film.

Project description:Deep-ultraviolet (DUV) light-transparent conductive composite thin films, consisting of dispersed multiwalled carbon nanotubes (MWCNTs) and SiO2 matrix composites, were fabricated on a quartz glass substrate. Transparent and well-adhered amorphous thin films, with a thickness of 220 nm, were obtained by weak ultraviolet (UV) irradiation (4 mW cm-2 at 254 nm) for more than 6 h at 20-40 °C onto the precursor films, which were obtained by spin coating with a mixed solution of MWCNT in water and Si(IV) complex in ethanol. The electrical resistivity of MWCNT/SiO2 composite thin film is 0.7 Ω·cm, and transmittance in the wavelength region from DUV to visible light is higher than 80%. The MWCNT/SiO2 composite thin film showed scratch resistance at pencil hardness of 8H. Importantly, the resistivity of the MWCNT/SiO2 composite thin film was maintained at the original level even after heat treatment at 500 °C for 1 h. It was observed that the heat treatment of the composite thin film improved durability against both aqueous solutions involving a strong acid (HCl) and a strong base (NaOH).

| S-EPMC8161176 | biostudies-literature

UV-protection from chitosan derivatized lignin multilayer thin film.

Project description:Lignin is one of the most abundant renewable materials on the earth. Despite possessing useful antioxidant and UV absorbing properties, its effective utilization in technology has been hampered by its relative insolubility and difficulty to process. In this work, a simple chemical derivatization process is utilized which yields water-soluble lignin possessing anionic carboxylate groups. These carboxylate groups give lignin polyanionic behavior and enable its utilization in the growth of a functional film via layer-by-layer (LbL) assembly with biologically sourced chitosan. The growth mechanism of this film is hypothesized to be a result of both hydrogen bonding and ionic interactions. The film demonstrates excellent UV-absorptive capability. A 100 nm thick chitosan/lignin coating was applied to a poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) film and shown to reduce its degradation sixfold over the course of a 1 hour exposure to harsh UV light. This is the first demonstration of lignin being utilized in a fully biologically derived LbL film. Utilization of lignin in LbL assembly is an important step in the development of renewable nanotechnology.

| S-EPMC9056636 | biostudies-literature

Precise Synthesis and Thin Film Self-Assembly of PLLA-b-PS Bottlebrush Block Copolymers.

Project description:The ability of bottlebrush block copolymers (BBCPs) to self-assemble into ordered large periodic structures could greatly expand the scope of photonic and membrane technologies. In this paper, we describe a two-step synthesis of poly(l-lactide)-b-polystyrene (PLLA-b-PS) BBCPs and their rapid thin-film self-assembly. PLLA chains were grown from exo-5-norbornene-2-methanol via ring-opening polymerization (ROP) of l-lactide to produce norbornene-terminated PLLA. Norbonene-terminated PS was prepared using anionic polymerization followed by a termination reaction with exo-5-norbornene-2-carbonyl chloride. PLLA-b-PS BBCPs were prepared from these two norbornenyl macromonomers by a one-pot sequential ring opening metathesis polymerization (ROMP). PLLA-b-PS BBCPs thin-films exhibited cylindrical and lamellar morphologies depending on the relative block volume fractions, with domain sizes of 46-58 nm and periodicities of 70-102 nm. Additionally, nanoporous templates were produced by the selective etching of PLLA blocks from ordered structures. The findings described in this work provide further insight into the controlled synthesis of BBCPs leading to various possible morphologies for applications requiring large periodicities. Moreover, the rapid thin film patterning strategy demonstrated (>5 min) highlights the advantages of using PLLA-b-PS BBCP materials beyond their linear BCP analogues in terms of both dimensions achievable and reduced processing time.

| S-EPMC7961899 | biostudies-literature

Novel Deposition Method of Crosslinked Polyethylene Thin Film for Low-Refractive-Index Mid-Infrared Optical Coatings.

Project description:Mid-infrared optics require optical coatings composed of high- and low-refractive-index dielectric layers for the design of optical mirrors, filters, and anti-reflection coatings. However, there are not many technologies for depositing a material with a refractive index of less than 2 and a low loss in the mid-infrared region. Here, we present a unique deposition method of crosslinked polyethylene thin film for mid-IR optical filter design. Polyethylene has a refractive index of 1.52 in the mid-infrared region and a small number of absorption peaks, so it is useful for making optical filters in the mid-infrared region. Only 1 keV of energy is required to crosslink the entire film by irradiating an electron beam while depositing polyethylene. In addition, crosslinked polyethylene thin film has high mechanical strength, so there is no cracking or peeling when used with germanium. This allows for the use of crosslinked polyethylene as a low refractive index for mid-infrared optical coating.

| S-EPMC10748295 | biostudies-literature

Negative threshold voltage shift in an a-IGZO thin film transistor under X-ray irradiation.

Project description:We investigated the effects of X-ray irradiation on the electrical characteristics of an amorphous In-Ga-Zn-O (a-IGZO) thin film transistor (TFT). The a-IGZO TFT showed a negative threshold voltage (V TH) shift of -6.2 V after 100 Gy X-ray irradiation. Based on spectroscopic ellipsometry (SE) and X-ray photoelectron spectroscopy (XPS) analysis, we found that the Fermi energy (E F) changes from 2.73 eV to 3.01 eV and that the sub-gap state of D1 and D2 changes near the conduction band minimum (CBM) of the a-IGZO film after X-ray irradiation. These results imply that the negative V TH shift after X-ray irradiation is related to the increase in electron concentration of the a-IGZO TFT active layer. We confirmed that the sources for electron generation during X-ray irradiation are hydrogen incorporation from the adjacent layer or from ambient air to the active layer in the TFT, and the oxygen vacancy dependent persistent photocurrent (PPC) effect. Since both causes are reversible processes involving an activation energy, we demonstrate the V TH shift recovery by thermal annealing.

| S-EPMC9065737 | biostudies-literature

Deep learning for augmented process monitoring of scalable perovskite thin-film fabrication.

Project description:Reproducible large-area fabrication is one of the remaining challenges for the commercialization of perovskite photovoltaics. Imaging methods augmented with deep learning (DL) enable in-line detection of spatial or temporal inconsistencies and predict the impact of observed changes on device performance. In this work, we showcase three use cases of how DL augments complex experimental data analysis of the large-area perovskite thin film formation, even on moderate-sized datasets. First, we demonstrate material composition monitoring by differentiating between precursor property variations, ensuring material consistency during fabrication. Second, we provide early thin-film quality assessment by predicting holistic device performance even before its finalization. Finally, we extend the approach from parameter prediction to generating recommendations for process control by forecasting monitoring signals as a function of a variable process parameter and predicting the corresponding device performances. By addressing tasks that are hardly possible for humans to solve, we present how DL augments data analysis by transforming experimental data into predictions of target parameters.

| S-EPMC11734647 | biostudies-literature

UV irradiation treatment

Project description:UV irradiation treatment Metagenome

| PRJNA688797 | ENA

PDAP1 RIP in UV-crosslinked human T cells

Project description:Human CD4+ Total memory cells (CD4+CD25-CD45RA-CCR7+/-) were activated for 5d with anti-CD3/anti-CD28 antibodies. About 40*10^6 cells were then irradiated twice with 254nm UV light at 0.2J and then lysed in RIPA buffer. 1mg of cell extract was incubated on a rotating wheel ~16 h at 4°C with anti-PDAP1 antibody. PDAP1:mRNA complexes were immunoprecipitated with protein-G dynabeads 4hrs at 4°C and then treated with proteinase K. RNA was then purified using TRI-reagent and RNA zymospin columns. Three independent donors were used for this experiment. Inputs were also sequenced. Total RNA was sequenced in paired-end mode. This experiment is assessing direct targets bound by PDAP1 in human T cells.

2022-01-10 | GSE183685 | GEO

UV-C-Activated Riboflavin Crosslinked Gelatin Film with Bioactive Nanoemulsion for Enhanced Preservation of Fresh Beef in Modified Atmosphere Packaging.

Project description:This study explores a new eco-friendly approach for developing bioactive gelatin films using UV-C irradiation-induced photo-crosslinking. Riboflavin, a food-grade photoinitiator, was selected at an optimal concentration of 1.25% (w/w) for crosslinking gelatin under UV-C exposure for 4 to 22 min. Physicochemical analyses revealed enhanced tensile strength, reduced water vapor permeability, and lower water solubility in films crosslinked for up to 13 min. FTIR analysis demonstrated significant molecular changes, confirming the formation of crosslinking connections in gelatin-riboflavin films. Antimicrobial nanoemulsion (NE) (0.5, 0.75, 1% v/v) was incorporated into crosslinked films and applied to fresh beef. The 1% NE film exhibited the strongest antimicrobial effect, extending shelf-life by 20 days. In vitro release study confirmed Fickian diffusion behavior in the 1% NE film. This study also investigated the synergy between 1% NE film and three different types of modified atmosphere packaging (MAP) on the microbiological and physicochemical properties of beef for 26 days. The best results were achieved with 1% NE film under MAP1 and MAP2, which preserved meat redness and prevented lipid oxidation, extending the shelf-life up to 26 days. Therefore, UV-C irradiation-induced crosslinked bioactive film combined with high-oxygen MAP offers a promising solution for prolonging the shelf-life of beef.

| S-EPMC11544885 | biostudies-literature

Fabrication of Transparent and Conductive SWCNT/SiO2 Composite Thin-Film by Photo-Irradiation of Molecular Precursor Films.

Project description:A single-walled carbon nanotube (SWCNT)-silica composite thin film on a quartz glass was formed by ultraviolet irradiation (20-40 °C) onto a spin-coated precursor film. With 7.4 mass% SWCNTs, the electrical resistivity reached 7.7 × 10-3 Ω·cm after UV-irradiation. The transmittance was >80% at 178-2600 nm, and 79%-73% at 220-352 nm. Heat treatment increased the transparency and pencil hardness, without affecting the low electrical resistivity. Raman spectroscopy and microscopic analyses revealed the excellent film morphology with good SWCNT dispersal. The low refractive index (1.49) and haze value (<1.5%) are invaluable for transparent windows for novel optoelectronic devices.

| S-EPMC8707605 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data