Development of AlN and TiB₂ Composites with Nb₂O₅, Y₂O₃ and ZrO₂ as Sintering Aids.
Ontology highlight
ABSTRACT:
SUBMITTER: Gonzalez JC
PROVIDER: S-EPMC5503357 | biostudies-other | 2017 Mar
REPOSITORIES: biostudies-other
Similar Datasets
Project description:TiB2 is a promising material for several fields including impact-resistant armor, wear-resistant coatings, cutting tools and crucibles given its physical, mechanical and chemical properties, especially due to the combination of high hardness and exceptional wear resistance. It is however very difficult to sinter below 2000 °C, even under mechanical pressure; moreover, the low fracture toughness limits the applicability of the ceramic material. By using sintering additives, it is possible to improve the sintering process and increase the mechanical properties since the additives react with oxidized layers and form secondary phases. In this study, different preparation methods and various combinations of additives (B4C, Si3N4 and MoSi2) via hot pressing sintering have been explored. Through the synergy between optimized process and tailored composition, an almost fully dense material was obtained at 1700 °C with hardness of 24.4 ± 0.2 GPa and fracture toughness of 5.4 ± 0.2 MPa m1/2. However, the highest hardness (24.5 ± 0.2 GPa) and density values were obtained for only the high-energy-milled sample with WC-Co media, featuring a core-shell grain structure. Finally, optical properties for selected samples were measured, identifying the high-energy-milled TiB2 as the sample with the highest spectral selectivity α/ε and solar absorptance.
| S-EPMC10574485 | biostudies-literature
Project description:The densification behavior, microstructure and mechanical properties of bulk TiB₂-based ceramic composites, fabricated using the spark plasma sintering (SPS) technique with elements of (Fe-Ni-Ti-Al) sinter-aid were investigated. Comparing the change of shrinkage displacement of pure TiB₂ and TiB₂-5 wt% (Fe-Ni-Ti-Al), the addition of elements Fe-Ni-Ti-Al into TiB₂ can facilitate sintering of the TiB₂ ceramics. As the sintering temperature exceeds 1300 °C, the relative density does not significantly change. Alumina particles and austenite (Fe-Ni-Ti) metallic binder distributed homogeneously in the grain boundary of TiB₂ can inhibit the growth of the TiB₂ grains when the sintering temperature is below 1300 °C. The density and particle size of TiB₂ greatly influence the mechanical behavior of TiB₂-5 wt% (Fe-Ni-Ti-Al) composites. The specimen sintered at 1300 has the highest microhardness of 21.1 ± 0.1 GPa with an elastic modulus of 461.4 GPa. The content of secondary borides (M₂B, being M = Fe, Ni), which are more brittle than TiB₂ particles, can also influence the fracture toughness. The specimen sintered at 1500 °C has the highest fracture toughness of 6.16 ± 0.30 MPa·m1/2 with the smallest M₂B phase. The results obtained provide insight into fabrication of ceramic composites with improved mechanical property.
| S-EPMC5456019 | biostudies-other
Project description:The development of high-power white light-emitting diodes demands highly efficient and stable all-inorganic color converters. In this respect, phosphor-glass/ceramic composites show great promise as they could combine the merits of high quantum efficiency of phosphors and high chemical and thermal stabilities of glass/ceramic matrices. However, strong interfacial reaction between phosphors and matrices at high temperature results in quantum efficiency loss of the embedded phosphors, and traditional solutions rely on high-pressure consolidation techniques. Here we report the intrinsic inhibition of interfacial reaction by using silica glass rather than multicomponent glasses as the matrix. The embedment of phosphors is achieved via a pressureless sintering method, rendering these color-tunable phosphor-glass composites not only accessible to three-dimensional printing technique, but also highly efficient (internal quantum efficiency >90.0%), thermally stable at 1200 °C and hydrothermally stable at 200 °C. Our results provide a facile and general strategy for developing all-inorganic functional composites.
| S-EPMC7272639 | biostudies-literature
Project description:Interior residual stresses induced by quenching may cause distortion during subsequent machining processes. Hence, various strategies have been employed to relieve the interior residual stress, such as stretching, post treatment, and other techniques. In this study, the stress distribution inside TiB₂/7050 Al composite extrusions was investigated and the effects of different methods on relieving the quenching-induced stress were compared. Firstly, three TiB₂/7050 Al composite extrusions were treated by stretching, stretching and heat treatment, and stretching and cold treatment processes, respectively. Then, the multiple-cut contour method was employed to assess the residual stresses in the three workpieces. Experimental results indicate that the interior stress of TiB₂/7050 Al composite extrusions after stretching ranges from −89 MPa to +55 MPa, which is larger than that in 7050 aluminum alloy, which ranges from −25 Pa to +25 MPa. The heat treatment performs better than the cold treatment to reduce the post-stretching residual stress, with a reduction of 23.2⁻46.4% compared to 11.3⁻40.8%, respectively. From the stress map, it is found that the stress distribution after the heat treatment is more uniform compared with that after the cold treatment.
| S-EPMC5978083 | biostudies-literature
Project description:Polymer-based composites with high thermal conductivity and dielectric breakdown strength have gained increasing attention due to their significant application potential in both power electronic devices and power equipment. In this study, we successfully prepared novel sandwich AlN/epoxy composites with various layer thicknesses, showing simultaneously and remarkably enhanced dielectric breakdown strength and thermal conductivity. The most optimized sandwich composite, with an outer layer thickness of 120 μm and an inner layer thickness of 60 μm (abbreviated as 120-60) exhibits a high through-plane thermal conductivity of 0.754 W/(m·K) (4.1 times of epoxy) and has a dielectric breakdown strength of 69.7 kV/mm, 8.1% higher compared to that of epoxy. The sandwich composites also have higher in-plane thermal conductivity (1.88 W/(m·K) for 120-60) based on the novel parallel models. The sandwich composites with desirable thermal and electrical properties are very promising for application in power electronic devices and power equipment.
| S-EPMC8401393 | biostudies-literature
Project description:Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, an increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNTs) grown on aluminum nitride (AlN). We combined catalyst coating technology with vacuum filtration to ensure that the catalyst was uniformly applied to micrometer-sized AlN particles, followed by the efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we achieved precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical influence of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials, with potential implications for a wide range of applications.
| S-EPMC10974482 | biostudies-literature
Project description:High-entropy ceramics and their composites display high mechanical strength and attractive high-temperature stabilities. However, properties like strong covalent bond character and low self-diffusion coefficients make them difficult to get sintered, limiting their mass popularity. Here, we present a rapid liquid phase-assisted ultrahigh-temperature sintering strategy and use high-entropy metal diboride/boron carbide composite as a proof of concept. We use a carbon-based heater to fast-heat the composite to around 3000 K, and a small fraction of eutectic liquid was formed at the interface between high-entropy metal diborides and boron carbide. A crystalline dodecaboride intergranular phase was generated upon cooling to ameliorate the adhesion between the components. The as-sintered composite presents a high hardness of 36.4 GPa at a load of 0.49 N and 24.4 GPa at a load of 9.8 N. This liquid phase-assisted rapid ultrahigh-temperature strategy can be widely applicable for other ultrahigh-temperature ceramics as well.
| S-EPMC9258815 | biostudies-literature
Project description:In this paper, the microstructure, the room-temperature and high-temperature tensile mechanical properties of monolithic TA15 alloy and TiB whisker-reinforced TA15 titanium matrix composites (TiBw/TA15) fabricated by vacuum hot-pressing sintering were investigated. The microstructure results showed that there were no obvious differences in the microstructure between monolithic TA15 alloy and TiBw/TA15 composites, except whether or not the grain boundaries contained TiBw. After sintering, the matrix microstructure presented a typical Widmanstätten structure and the size of primary β grain was consistent with the size of spherical TA15 titanium metallic powders. This result demonstrated that TiBw was not the only factor limiting grain coarsening of the primary β grain. Moreover, the grain coarsening of α colonies was obvious, and high-angle grain boundaries (HAGBs) were distributed within the primary β grain. In addition, TiBw played an important role in the microstructure evolution. In the composites, TiBw were randomly distributed in the matrix and surrounded by a large number of low-angle grain boundaries (LAGBs). Globularization of α phase occurred prior, near the TiBw region, because TiBw provided the nucleation site for the equiaxed α phase. The room-temperature and high-temperature tensile results showed that TiBw distributed at the primary β grain boundaries can strengthen the grain boundary, but reduce the connectivity of the matrix. Therefore, compared to the monolithic TA15 alloy fabricated by the same process, the tensile strength of the composites increased, and the tensile elongation decreased. Moreover, with the addition of TiBw, the fracture mechanism was changed to a mixture of brittle fracture and ductile failure (composites) from ductile failure (monolithic TA15 alloy). The fracture surfaces of TiBw/TA15 composites were the grain boundaries of the primary β grain where the majority of TiB whiskers distributed, i.e., the surfaces of the spherical TA15 titanium metallic powders.
| S-EPMC5506956 | biostudies-other
Project description:Constructing continuous filler networks in a polymer matrix can significantly improve the thermal conductivity of the composite. In this study, we fabricated porous Al2O3 frameworks (f-AO) by decomposing the sacrificial material and sintering to serve as heat conduction pathways in the matrix. Then, epoxy/Al2O3 frameworks (EP/f-AO) composites with excellent thermal conductivity were obtained by vacuum infiltration. The pre-constructed Al2O3 frameworks and sintering reduce interfacial thermal resistance by 1 order of magnitude and result in a dramatically enhanced thermal conductivity of EP/f-AO composites. At the filler content of 49.5 vol %, the thermal conductivity of the EP/f-AO composite is 6.96 W m-1 K-1, which is 4.3 times that of the EP/AO composite (1.61 W m-1 K-1) with randomly dispersed fillers. The heat dissipation capability of the EP/f-AO composites was further confirmed by infrared thermal imaging. This study provides a promising approach for fabricating thermal conductive polymer composites as electronic package materials.
| S-EPMC9835650 | biostudies-literature
Project description:Carbon fiber-reinforced titanium matrix composites were prepared by powder metallurgy. Carbon fiber (CF) powder and titanium (Ti) powder are mixed, pressed, and then sintered at a high temperature of 1300-1500 °C. The morphology and conductivity of carbon fiber-reinforced titanium matrix (Ti-CF) composites were studied. When the temperature range of the Ti-CF composites was from 1300 to 1500 °C, the porosity and resistivity first decreased and then increased. When the sintering temperature was 1350 °C, the diffraction peak of the sample was the strongest, the porosity was the smallest (4.16%), and the resistivity was the smallest (2.7 MΩ·mm). CFs have a very good strengthening effect on titanium-based composite materials.
| S-EPMC9434608 | biostudies-literature